Oiling System

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

K&P Engineering High Performance Stainless Steel Micronic Oil Filter w/ Machine Finished End Caps is an advanced solution for superior oil filtration in automotive applications. This filter is designed to offer exceptional protection against oil contamination, ensuring optimal engine performance and longevity.

• High-Quality Stainless Steel Construction: Made from medical-grade type 304 stainless steel micronic filter cloth, which filters down to 35 microns and provides a high flow rate of 1.9 gallons per minute per square inch.
• Cleanable and Reusable: Unlike paper filters, this stainless steel filter can be washed and reused, offering both cost savings and environmental benefits.
• Consistent Filtration: Delivers reliable filtering performance across the entire filter surface, maintaining engine protection.
• Superior Filtration Performance: Achieves excellent ASTMF316 filtration standards and includes magnetic prefiltering to capture metallic particles.
• Billet Aluminum Filter Case: Acts as an oil cooler (where applicable) and adds durability.
• Progressive Rate Bypass: Combined with high flow characteristics, this feature prevents unfiltered oil from bypassing the filter during cold starts and high RPMs.
• Easy Contamination Inspection: Allows for straightforward inspection of engine contamination levels.
• Proven Track Record: Trusted in motorsports, military, and aerospace applications.

Please note: For older caged-type filters, a newer filter housing is required. Ensure the larger hole insert is installed on the housing cap for proper fitment.

Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!

The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.

K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top-tier product for your European vehicle.

Features:

• Consistent filtering across entire filter surface
• Superior ASTMF316 filtration performance
• 7 times the flow of comparable paper oil filters
• Magnetic Prefiltering
• Progressive rate bypass combined with high flow characteristics of the filter media avoids unfiltered oil bypassing the filter during cold startup and high rpm
• No more cutting apart messy paper filters for trapped debris inspection
• Proven in Motorsports, Military and Aerospace applications for years. Technology is FAA approved for use in aircraft. 

At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.

Watch to learn how to clean a K&P oil filter

This product fits the following BMWs:
1975-1983 E21 320i
1982-1991 E30 325i
1982-1988 E28 528i 528e
1989-1995 E34 525i
 

Rally Road Productions, Inc. is a team supported by a group of people with great abilities in their area of expertise. From the "web guy" and driving instructor friends, to owners of various machine shops, they have surrounded ourselves with people that can be trusted to create and manufacture quality products. This is the key to ensuring everything that they sell will perform as it was intended. The goal is to increase customer satisfaction and make the customization or performance enhancement of your vehicle a more enjoyable venture.

This oil cooler system is race tested and proven to outflow the euro M3 oil filter housing. Additionally, this particular system uses a sealing mechanism to direct the oil flow through the cooler lines and then through the oil filter.  Other cooler caps do not provide this seal and therefore the external oil coolers and lines act as a "balloon".  The lines and cooler are pressurized, but oil does not flow through them.  Flowing oil means it is being cooled and not just acting as an external reservoir.

Flow testing reveals that the oil cooler cap will outflow the Euro M3 Oil Filter Housing by more than 80% at the same, pressure, RPM, and oil temperature. In the upper RPM range, there is nearly a 100% improvement in flow from the RallyRoad oil cooler cap when compared to the Euro M3 oil filter housing.  This is a massive improvement over OE and is a worthwhile upgrade, especially in engines that see severe duty.

Features:

• -8AN o-ring ports to provide a leak free fitting without the use of Teflon tape or sealant used by other oil cooler caps.
• Viton o-rings are used throughout to maintain function and sealing in a high-temperature oil environment.
• Use of the stock filter cap bolt to reduce cost and simplify installation.
• An internal sealing mechanism to direct oil flow through the oil cooler and through the filter.
• 1/8" NPT side port for external oil pressure gauge.

Kit Includes:

• Oil filter cap with fittings
• Oil filter sealing ring
• BMW MANN Oil Filter and gasket

This part fits the following BMWs
1992-1999 E36 323i 325i 325is 328i 328is