Stock mounts are made from soft rubber and are sometimes filled with fluid to give a car the most comfortable ride possible. The soft rubber and fluid helps to reduce the total amount of vibration, noise, and harshness (NVH) that is transferred into the cabin. The problem with this is driveline slop. The stock mounts allow a lot of excess movement and increases the amount of time it takes to transfer power to the wheels.
In order to address this issue, performance mounts can be substituted to reduce the amount of slop and transfer power to the wheel quicker. Two options for this are polyurethane mounts and solid mounts.
Solid mounts are great for an immediate transfer of power but allow for a ton of noise and vibration to be felt and heard in the cabin of the vehicle. This is great for the track where there aren't any issues with excess harshness, but as a daily driver, this can become an annoying pain in the neck.
The best middle ground is Polyurethane. Polyurethane is much stiffer than rubber and gives you the much stiffer feel you may be looking for. This allows for the increase in responsiveness, but isn't so extreme that it transfers all of the sound and vibrations into the cabin. This makes it much more comfortable for daily use while still reinforcing your driveline.
Features:
This product was last offered at the strikethrough price on
04-06-2026
Rein Transfer Case Fluid TF 0870 is designed to service your BMW xDrive transfer case, ensuring optimal performance and reliability. This genuine BMW fluid is essential for maintaining the efficiency of your transfer case, especially if you are nearing or exceeding the 60,000-mile mark. Using Rein Transfer Case Fluid TF 0870 helps to catch up on crucial maintenance and keep your vehicle running smoothly.
One of the most satisfying upgrades you can make to your BMW is to its factory shifter mechanism. By reducing the shifter's throw, you can give your manual transmission BMW a sportier, more precise feel. However, with so many different "short shift kits" out there, how can you be sure you're making the right decision? With the introduction of the Rogue Engineering OCTANE short shift kit, the choice is now crystal clear!
Rogue Engineering refuses to compromise with "lever substitution" as a method of short shift kit development. Rather than using actual test vehicles for their products, some companies actually dig through OEM factory parts diagrams to determine which factory levers can be substituted with others. This "lever substitution" method of introducing product is unacceptable. These shift kits have been developed and perfected through years of experience in proven short shifter technology, by Co-Founder, Ben Liaw. As longtime BMW enthusiasts know, Ben was single-handedly responsible for introducing and developing the idea of affordable, BMW factory-like, short shift kits for late model BMWs (BL/SS for those young enough to remember!).
Rogue Engineering idea of a short shift kit is not substituting levers in place of factory ones just because "they fit". Throughout the 80s until recently, BMW was notorious for using only a few specific shifter levers for their manual transmission vehicles. For other companies, making just a few "replacement levers" and offering them in place of those factory part numbers was an easy way of calling it a short shift kit. Unfortunately, for those companies, BMW started using many different part numbers making it more difficult to just "swap in a lever".
Rogue Engineering only develops it's short shift kit with test vehicles in their facility, testing numerous prototypes, offering others to test it before settling on its final design. They feel that this old school, real world testing is the best way when modifying OEM ergonomic, sensory-based controls.
Stock rubber flex discs allow for a slight amount of give, especially under heavy acceleration and, depending on the amount of force applied, could potentially tear or split. This slight flex/give can prevent instantaneous transfer of force to the wheels, making accelerations unpredictable, or even lead to your vehicle being stuck on the side of the track. To combat this, IRP's Performance Flex Disc was developed. Made of CNC machined aluminum, this flex disc won't actually flex, and the polyurethane bushings will only provide a enough give to dampen some vibrations and prevent damaging the transmission. This is perfect for high torque applications such a drag cars and dedicated track cars that want immediate response and long term reliability.
78mm Diameter with fitment for M12 nuts/bolts.
Applicatons:
1992-1998 E36 BMW 318i 318is 318ti 318ic - Manual Transmission
1992-1998 E36 BMW 323is 323ic 325i 325is 325ic - Manual and Automatic Transmission
1992-1998 E36 BMW 328i 328is 328ic - Automatic Transmission
1999-2005 E46 BMW 323i 323ci 325i 325ci - Manual Transmission
1997-2002 Z3 BMW Z3 1.9 - Manual Transmission
1999-2000 Z3 BMW Z3 2.3 M52TU - Manual and Automatic Transmission
2001-2002 Z3 BMW Z3 2.5i - Manual Transmission
1997-4/1999 Z3 BMW Z3 2.8 - Automatic Transmission
2003-2006 Z4 BMW Z4 2.5i - Manual and Automatic Transmission
Stock rubber flex discs allow for a slight amount of give, especially under heavy acceleration and, depending on the amount of force applied, could potentially tear or split. This slight flex/give can prevent instantaneous transfer of force to the wheels, making accelerations unpredictable, or even lead to your vehicle being stuck on the side of the track. To combat this, IRP's Performance Flex Disc was developed. Made of CNC machined aluminum, this flex disc won't actually flex, and the polyurethane bushings will only provide a enough give to dampen some vibrations and prevent damaging the transmission. This is perfect for high torque applications such a drag cars and dedicated track cars that want immediate response and long term reliability.
96mm Diameter
Fits the following BMWs:
2008+ E82 BMW 128i
5/1986-1991 E30 BMW 325e 325es M3 - Manual Transmission
1987-1991 E30 BMW 325ix - Between Transmission & Transfer Case
1996-1998 E36 BMW 328i 328is 328ic - Manual Transmission only
1999-2005 E46 BMW 323i 323ci 325i 325ci - Automatic & SMG Transmissions only
1999-2005 E46 BMW 328i 328ci 330i 330ci - Manual, Auto, and SMG
2006+ E90 BMW 325i 328i 330i - Manual or Automatic Transmission
2006+ E91 BMW 328i - Manual or Automatic Transmission
2007+ E92 BMW 328i - Manual or Automatic Transmission
2007+ E93 BMW 328 - Manual or Automatic Transmission
1982-1983 E28 BMW 528e - Manual Transmission
5/1986-1988 E28 BMW 528e - Manual Transmission
1982-1988 E28 BMW 533i 535i 535is M5 - Manual Transmission
1991-1995 E34 BMW 525i - Automatic Transmission
1989-6/1992 E34 BMW 525i - Manual Transmission
1993-1995 E34 BMW 530i - Manual or Automatic Transmission
1989-1993 E34 BMW 535i - Manual Transmission
2001-2003 E39 BMW 525i - Automatic Transmission
1997-2003 E39 BMW 528i 530i - Manual or Automatic Transmission
1980-1989 E24 BMW 633csi 635csi M6 - Manual Transmission
2000-2006 E53 BMW X5 3.0i - for Rear Driveshaft
2000-2003 E53 BMW X5 4.4i X5 4.6is - for Rear Driveshaft
2007-2013 E70 BMW X5 3.0si X5 4.8i X5 xDrive30i X5 xDrive48i - for Rear Driveshaft
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i - Automatic Transmission
1997-2002 Z3 BMW Z3 2.8 Z3 3.0i - Manual or Automatic Transmission
2003-2008 Z4 BMW Z4 2.5i - Automatic or SMG Transmission
2003-2008 Z4 BMW Z4 3.0i Z4 3.0si
One of the most satisfying upgrades you can make to your BMW is to its factory shifter mechanism. By reducing the shifter's throw, you can give your manual transmission BMW a sportier, more precise feel. However, with so many different "short shift kits" out there, how can you be sure you're making the right decision? With the introduction of the Rogue Engineering OCTANE short shift kit, the choice is now crystal clear!
Rogue Engineering refuses to compromise with "lever substitution" as a method of short shift kit development. Rather than using actual test vehicles for their products, some companies actually dig through OEM factory parts diagrams to determine which factory levers can be substituted with others. This "lever substitution" method of introducing product is unacceptable. These shift kits have been developed and perfected through years of experience in proven short shifter technology, by Co-Founder, Ben Liaw. As longtime BMW enthusiasts know, Ben was single-handedly responsible for introducing and developing the idea of affordable, BMW factory-like, short shift kits for late model BMWs (BL/SS for those young enough to remember!).
Rogue Engineering idea of a short shift kit is not substituting levers in place of factory ones just because "they fit". Throughout the 80s until recently, BMW was notorious for using only a few specific shifter levers for their manual transmission vehicles. For other companies, making just a few "replacement levers" and offering them in place of those factory part numbers was an easy way of calling it a short shift kit. Unfortunately, for those companies, BMW started using many different part numbers making it more difficult to just "swap in a lever".
Rogue Engineering only develops it's short shift kit with test vehicles in their facility, testing numerous prototypes, offering others to test it before settling on its final design. They feel that this old school, real world testing is the best way when modifying OEM ergonomic, sensory-based controls.
This product was last offered at the strikethrough price on
07-03-2026
This product was last offered at the strikethrough price on
06-08-2026
One of the most satisfying upgrades you can make to your BMW is to its factory shifter mechanism. By reducing the shifter's throw, you can give your manual transmission BMW a sportier, more precise feel. However, with so many different "short shift kits" out there, how can you be sure you're making the right decision? With the introduction of the Rogue Engineering OCTANE short shift kit, the choice is now crystal clear!
Rogue Engineering refuses to compromise with "lever substitution" as a method of short shift kit development. Rather than using actual test vehicles for their products, some companies actually dig through OEM factory parts diagrams to determine which factory levers can be substituted with others. This "lever substitution" method of introducing product is unacceptable. These shift kits have been developed and perfected through years of experience in proven short shifter technology, by Co-Founder, Ben Liaw. As longtime BMW enthusiasts know, Ben was single-handedly responsible for introducing and developing the idea of affordable, BMW factory-like, short shift kits for late model BMWs (BL/SS for those young enough to remember!).
Rogue Engineering idea of a short shift kit is not substituting levers in place of factory ones just because "they fit". Throughout the 80s until recently, BMW was notorious for using only a few specific shifter levers for their manual transmission vehicles. For other companies, making just a few "replacement levers" and offering them in place of those factory part numbers was an easy way of calling it a short shift kit. Unfortunately, for those companies, BMW started using many different part numbers making it more difficult to just "swap in a lever".
Rogue Engineering only develops it's short shift kit with test vehicles in their facility, testing numerous prototypes, offering others to test it before settling on its final design. They feel that this old school, real world testing is the best way when modifying OEM ergonomic, sensory-based controls.
This product was last offered at the strikethrough price on
05-27-2026
Stock rubber flex discs allow for a slight amount of give, especially under heavy acceleration and, depending on the amount of force applied, could potentially tear or split. This slight flex/give can prevent instantaneous transfer of force to the wheels, making accelerations unpredictable, or even lead to your vehicle being stuck on the side of the track. To combat this, IRP's Performance Flex Disc was developed. Made of CNC machined aluminum, this flex disc won't actually flex, and the polyurethane bushings will only provide a enough give to dampen some vibrations and prevent damaging the transmission. This is perfect for high torque applications such a drag cars and dedicated track cars that want immediate response and long term reliability.
110mm Diameter
This item fits the following BMW Chassis:
E60 M5,E63 M6,E63,E90,E92,E93
This product was last offered at the strikethrough price on
05-07-2026
This product was last offered at the strikethrough price on
05-07-2026
Don't neglect your motor mounts! Most stock BMW motor mounts are fluid filled and the stiffness of the mount depends on this fluid. But over time the fluid leaks out and the strength of the mount is greatly reduced. A worn motor mount allows the engine to twist and shift around. The harder you're driving the more shift will occur. As the engine is moving around it can contact other parts in the engine bay - usually cooling related. The mechanical fan can hit the radiator; the A/C compressor can hit a radiator hose, the exhaust will flex and may break. Twisting of the engine can also lead to shifting problems as the transmission twists with it. There are countless issues related to worn or compressed motor mounts so don't overlook these as a regular replacement item (every 50,000 miles).
As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!
This item fits the following BMWs:
E60 BMW 5 Series - 525i 528i 530i 535i
