BMW Performance Clutch Kits & Parts

Give your factory clutch a heavier motorsport feel or make your extremely tough clutch more drivable! If you have an E36 there is absolutely no reason you don't have this clutch pedal! Your factory E36 clutch pedal is made of flimsy plastic with no adjustment at all, leaving you to the mercy of the clutch you have.

Our Turner Performance Adjustable Clutch Pedal is a rigid design that gives you the ability to fully adjust your clutch feel and performance. With both upper and lower adjustments this is the best pedal on the market to fine tune your clutch pedal just the way you like it. The upper eccentric provides an adjustable pedal ratio to fine tune clutch pedal effort(how heavy the pedal feels). The lower adjustment is to change the position of the clutch assist spring, this allows you to choose where the clutch assisting spring engages. Changing where the spring engages will move the area of tension on your clutch from lower, middle to higher for maximum adjustment.

Your race car no longer needs to have a clutch that makes the car undriveable on the street. Your track car can now be your daily driver or weekend cruiser.

Features:

Adjustable throw
Capable of quicker shifts
Three lower mounting points for the spring to adjust where the assistance engages
Eccentric mount for master cylinder to adjust leverage ratio and pedal feel(weight/force needed to engage the clutch)
Self lubricating bronze bushings
All necessary hardware required for installation
Pedal body and pedal are constructed from 6061-T6 aluminum and type II black anodized for a great finish
NOTE: This Clutch Pedal does not include the Compression spring and the original spring must be reused. If you'd like to purchase a new spring, please see:

35311162505 - Non-M E36 - T#64615
21522227764 - E36 M3 - T#21753

If you've ever bled the clutch hydraulic system on your BMW, you know how frustrating it can be. Designed with both DIY enthusiasts and professional technicians in mind, our clever tool simplifies one of the most notoriously annoying steps in clutch service.

Crafted from high-quality aluminum and finished in a durable black anodized coating, our clutch slave cylinder bleeder tool is built to last. Its function is simple: the adjustable piston rod applies controlled pressure directly to the clutch slave cylinder’s piston, compressing it and reducing its internal volume. By minimizing the amount of air trapped inside the cylinder, bleeding becomes faster, cleaner, and far more effective—no more endless pedal pumping or inconsistent clutch feel. The result is firm, consistent clutch pedal engagement and a smoother overall driving experience, all achieved with less time and effort underneath the car.

FEATURES & BENEFITS

Simplifies bleeding the BMW clutch hydraulic system by reducing trapped air in the slave cylinder Eliminates excessive pedal pumping and inconsistent clutch feel Helps achieve firm, consistent clutch pedal engagement Crafted from high-quality aluminum for strength and longevity Durable black anodized finish resists wear and corrosion Designed for both DIY enthusiasts and professional technicians PRODUCT DEVELOPMENT

Our Clutch Slave Cylinder Bleeder Tool was designed, engineered, tested, and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology, including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.

Engineered in-house, we designed this lightweight, single-mass flywheel to provide more than 10 pounds of weight savings over the factory flywheel. While some ultra-lightweight performance flywheels are manufactured from aluminum, our designers opted for a more driveable experience with steel. The mass provided by steel helps dampen vibrations and noise, delivering near-factory refinement with most of the benefits of a lightweight flywheel: quicker throttle response, improved durability (and longevity), and more effective transfer of power to the wheels.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

When it comes to selecting a clutch to pair with a lightweight flywheel, consider the driving you’ll be doing. As a single mass flywheel eliminates the dual-mass dampening of the factory flywheel, to retain the lowest noise, lowest harshness driving experience possible, select a clutch with a dampened disc such as the ACT Heavy Duty. For dedicated track cars, a solid clutch hub is appropriate.

Our recommendations:

Street: ACT Heavy Duty
Track: ACT Xtreme for high torque cars or OE 335is LuK (with 440lbs-ft or less)
Features:

Precision machined from 4140 HT heat treated chromoly steel for exceptional toughness, even wear properties, and durability.
Material quality promotes even wear across the entire friction surface
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability and elevated temperatures
Hardness improves wear characteristics
Black oxide coated for corrosion resistance on non-friction surfaces.
8620 steel pilot bearing pin, case hardened and Precision ground for maximum wear resistance.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
SFI 1.1 tested and certified to ensure safe operation under extreme operating conditions
SFI 1.1 specifies minimum material properties and requires a 3rd party lab certification test, spinning the flywheel to 1.5x redline for 1 hour to ensure the flywheel will not burst.
Specifically designed to work with N54 architecture clutches
Step height designed to optimize clamp load and maximize the usable range of clutch wear for a long service life
Performance:

Turner Flywheel 18.6 lbs
10 lbs lighter than the factory BMW flywheel (Stock Flywheel 28.9 lbs)
Faster revs
Improved throttle response
Improved acceleration
Sportier driving experience
Stock flywheel weight - 28.9lbs
Turner single mass flywheel weight = 18.55lbs

Single Mass Flywheel Conversion:

Audible chatter from the transmission after installation is considered normal. As with most single mass flywheels, there is less dampening in the flywheel to reduce "gear noise." This chatter noise may be more present when the transmission fluid temperatures are hotter and may be intensified by other modifications. Most gearboxes will experience some chatter noise at hotter temperatures. Please be advised that this noise will disappear once the clutch pedal is depressed. This symptom may be lessened by adjusting transmission fluid weight, turning off electrical/driveline consumers (A/C, High Beams, ETC.), and by raising the RPM slightly.

Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

This item fits the following BMWs with 8 bolt flywheel and build date up to 01/2009 or earlier:
2008-01/2009 E82 BMW 135i 135is 1M
2007-01/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-01/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-01/2009 E93 BMW 335i - Convertible
2008-01/2009 E60 BMW 535i 535xi 535i xDrive

Lightweight flywheel for quicker, effortless revs that improve throttle response and free up lost horsepower. Tested and approved by our engineering team at Turner Motorsport. Tested in early, late, ETA and IS model E30s for confirmed fitment.

Introducing our Turner Flywheel: an ingenious blend of lightweight design, rich features, and remarkable strength! Crafted from 4140 HT Steel, this flywheel is precision-machined from a solid piece, ensuring unmatched durability. By strategically trimming excess weight from its original design, we've achieved a significant reduction in weight, giving new life to your M20 engine. With upgraded efficiency, your M20 can now swiftly spin to high RPMs, unleashing the full power and prowess of this formidable engine. Our flywheel features a ring gear profile compatible with all starters, alongside a reference tab tailored for early cars equipped with bellhousing-mounted sensor crank position detection.

Do you have an early model transmission with the crank sensors on the bellhousing? Maybe you have a late 325is with the crank sensor on the front of the engine, or maybe you have a 1988 super ETA. No matter which E30 model you have, our flywheel is the perfect choice for you.

During the engineering process we encountered the full spectrum of M20 and flywheel combinations. Early cars with bellhousing crank sensors, late cars with front mounting crank sensors and even a super ETA. On this adventure we found both early and late single mass flywheels and even the dual mass that we thought for sure was just a myth. At first we were hesitant that we could make one flywheel to fit them all but with the persistence of our engineering team(fleet of E30 enthusiasts) we can proudly say our M20 flywheel does in fact fit all engine and transmission applications you can think of.

Features and benefits:

Fits early and late models with M20
Fits shallow and deep bellhousing transmissions
Ring gear suited for both starters (P# 12411726504 + 12411361874)
Heavier than other lightweight flywheels, lighter than OEM, its like the Goldie Locks of flywheels - its just right
Reference pin for bellhousing crank sensor
Strong Single-Piece 4140 HT Steel construction
Designed to be used with factory and OE clutches
Weight Comparisons:

​Factory single mass flywheel EARLY (11221705046) - 23.69 lbs.
Factory single mass flywheel LATE (11221706573) - 18.74 lbs.
Dual mass flywheel (21211225979) - 27.56 lbs.
Turner flywheel - 14 lbs.
What you need:

Short bellhousing transmissions (I/IS) - Throw-out bearing P# 21517521471
Tall bellhousing transmission (ETA) - Throw-out bearing P# 21511204525

Adapt an N54 or N55 GS6-53BZ transmission to your M5x/S5x engine to unlock superior torque capacity and optimized gear ratios.

Engineered for the BMW enthusiast who demands more strength and better gear ratios, the Turner Motorsport Transmission Swap Flywheel Kit provides a direct solution for mating a modern N54 or N55 6-speed gearbox to your M20, M5X, or S5X engine. This kit bridges the gap between generations, allowing you to run a high-capacity GS6-53BZ transmission without the typical fabrication nightmares.

The technical core of this kit is our dual-geometry flywheel. By utilizing this specialized design, you can retain your engine-side stock starter while using the factory clutch and throw-out bearing from your donor transmission. This ensures a precise fit and a firm, factory-like shifting feel that can handle significantly more power than older 5-speed setups. To guarantee a fitment, we’ve included a precision drill guide for bellhousing alignment and a universal pilot bearing pin to simplify the installation process.

Features and benefits:

Compatible with the starter from your original motor.
Uses factory clutch and throwout bearing from the donor transmission (GS6-53BZ).
Comes with necessary tools and a provided drill guide to adapt the top transmission mounting holes.
Kit contents:

Swap Flywheel
Pilot bearing input adapter for late N54 and N55 GS6
Drill guide, bit, and hardware.
Flywheel bolts
Optional pilot bearing
Optional clutch
Swap notes:

Fits M20/M50/M52/S50/S52/S54 engines
Needs a custom driveshaft and rear transmission mount. (We used https://www.hdtautoparts.com/driveshafts)
For E46 only: Rear transmission mount can be used from E46 330 6 Speed. Part numbers (22316760531 & 22316760532)
Installation and Support:

Click HERE for installation instructions:

The factory BMW S65 dual-mass flywheel is engineered with comfort in mind, catering to the luxury-oriented expectations of the brand’s driving experience. Its design focuses on dampening drivetrain vibrations, smoothing out gear transitions, and minimizing harshness during operation. However, this refinement costs valuable performance. The dual-mass flywheel adds a substantial 27 lbs of rotational mass to the drivetrain, which significantly hinders throttle response and makes rev-matching feel sluggish and disconnected. Moreover, dual-mass flywheels are notorious for being a weak link in modified or high-performance builds and can prove costly to replace when they inevitably fail.

Our Single-Mass Lightweight Flywheel Conversion addresses all of these shortcomings with a purpose-built, lightweight, single-mass design that prioritizes performance. Weighing in at only 19 lbs., this design significantly reduces rotational mass, allowing your S65 to achieve its true motorsport potential!

Features & Benefits:

Precision machined from 4140 HT heat-treated chromoly steel for exceptional toughness, even wear properties, and increased durability.
Material quality promotes even wear across the entire friction surface, prolonging component lifespan.
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability.
Hardness improves component wear characteristics.
Black oxide coated for corrosion resistance on non-friction surfaces.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
Specifically designed to work with S65 OE-architecture clutches.
Optimized step height maximizes clutch clamp load and offers a prolonged service life.
Performance:

8 lbs. lighter than the factory BMW flywheel!
OEM Dual-Mass: 27 lbs.
Turner Motorsport Single-Mass: 19 lbs.
Faster revs
Improved throttle response and acceleration
Allows for a more engaging driving experience and delivers a feeling of direct connection
Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

Lightweight single mass flywheel paired with the Sachs clutch kit, perfect for naturally aspirated M20's! Fits early and late model cars.

A perfect upgrade and refreshment for your M20! Free up lost horsepower with the lightened single mass flywheel and get back the life in your clutch pedal. This kit is put together with the idea of an OEM+ upgrade, perfect for people looking to refresh the driving experience of their M20 and get back the full potential of this tried and true motor.

This kit includes everything you need to do the clutch and flywheel service on your M20. While you're in there it is a good idea also to purchase the common transmission seals, fluid, and mounting hardware which are listed below.

Clutch Kit:

Sachs OE replacement clutch disc - 21211223097
Sachs pressure plate - 21211223026
Sachs 323 throw-out bearing (taller bell housing/ETA models) - 21511204525
Pilot bearing - 11211720310
Turner Single-Mass Flywheel:

Lightweight flywheel for quicker, effortless revs that improve throttle response and free up lost horsepower. Tested and approved by the engineering team at Turner Motorsport, tested in early, late, ETA and IS model E30s for confirmed fitment.
Fits shallow and deep bell housing transmissions
Ring gear suited for both starters (P# 12411726504 + 12411361874)
Heavier than other lightweight flywheels, and lighter than OEM, it's like the Goldie Locks of flywheels - it's just right
Reference pin for bell housing crank sensor
Strong Single-Piece 4140 HT Steel construction
Designed to be used with factory and OE clutches
Weight savings between 5-14lbs depending on your OE flywheel

Components strongly suggested while your transmission is out of the car.:

Transmission Seals Kit - T#29898446
Fluid - 75-90 or preferred fluid type (approximately 1.25 liters)
Transmission Mounting hardware - T#30197962

The ECS Billet Master Cylinder Fitting is the ultimate solution for a notorious failure point in BMW E30 clutch systems. This critical fitting, located at the end of the master cylinder reservoir hose, is responsible for delivering hydraulic fluid to the clutch master cylinder inlet. Unfortunately, the OEM plastic fitting is prone to degradation after prolonged exposure to brake fluid, often leading to total hydraulic pressure loss and brake fluid leaks inside your vehicle.

ECS has addressed this issue by engineering a robust and long-lasting alternative. Crafted from 6061 billet aluminum and finished with black hard-coat anodizing for superior corrosion resistance, this precision-machined fitting replaces the fragile plastic original, ensuring leak-free performance for the lifetime of your vehicle. Upgrade to our Billet Master Cylinder Fitting during your next clutch master cylinder service and enjoy peace of mind knowing your BMW is equipped with a durable, high-quality solution.

Features & Benefits:

Made from 6061 billet aluminum for a permanent, reliable upgrade over the factory plastic fitting. Black hard-coat anodized finish ensures long-lasting protection against the elements. Precision-machined barbs match OEM dimensions for a leak-free seal with Genuine and aftermarket master cylinders. Designed for a secure fit within the factory grommet location. Prevents brake fluid leaks and loss of clutch hydraulic pressure caused by plastic fitting failure. Upgrade your BMW and bulletproof your master cylinder with the ECS Billet Aluminum Master Cylinder Fitting. Ensure clutch hydraulic system reliability and enjoy peace of mind knowing your failure-prone plastic master cylinder fitting has been addressed.

This braided stainless steel line replaces the stock hydraulic hose connecting your clutch slave cylinder to the clutch master cylinder. There are several deficiences with rubber, especially as it ages - when new the rubber expands and swells under pressure and the pedal can feel spongy. As rubber ages and is exposed to extreme temperatures the rubber can harden and even shrink (common on brake hoses), which results in a stiff pedal. Rubber clutch lines do not stand up to the stresses of hard use. ECS Exact-Fit stainless reinforced clutch lines provide more confident and dependable shifting by maintaining consistent line pressure, long lasting corrosion resistance, and increased protection from failure. These lines are reinforced with braided stainless steel mesh, affording superior expansion resistance. This resistance to expansion creates a firmer pedal, and a more direct clutch pedal feel. The signature red polymer coating provides additional protection from the elements and abrasion.

This particular stainless steel clutch line fits the following BMWs:
1992-1997 E36 BMW 318i 318is 318ic 318ti 325i 325is 325ic
1996-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5 Z3 2.8
1998-2000 Z3 BMW M Roadster M Coupe (S52)

Enhance the performance of your stick shift BMW with the BMS clutch valve, a must-have upgrade for serious BMW enthusiasts. This high-performance replacement replaces the factory clutch delay valve, resulting in quicker shifts, longer clutch life, and improved 0-60 times. Designed with CNC machined precision, it installs quickly using factory-like connections with no modifications required. Made in the USA, this clutch valve is essential for maximizing the driving experience of your BMW.

Benefits:

• Replaces factory clutch delay valve for improved performance
• Quicker shifts and improved 0-60 times
• Longer clutch life
• Easy installation with factory-like connections
• Made in the USA

BMW Clutch Stop

Improve your shifting experience with the BMW Clutch Stop. This adjustable clutch stop is designed to install beneath the clutch pedal, allowing you to set the precise stopping point just after the clutch disengages. Once adjusted, you can achieve consistent, smooth, and efficient shifts every time, saving valuable time and effort.

Benefits:

• Enhances shifting precision and consistency
• Saves time with smooth and fast shifts
• Adjustable design allows for personalized settings

Upgrade your BMW's shifting performance with the BMW Clutch Stop for a more enjoyable driving experience.

This braided stainless steel line replaces the stock hydraulic hose connecting your clutch slave cylinder to the clutch master cylinder. There are several deficiences with rubber, especially as it ages - when new the rubber expands and swells under pressure and the pedal can feel spongy. As rubber ages and is exposed to extreme temperatures the rubber can harden and even shrink (common on brake hoses), which results in a stiff pedal. Rubber clutch lines do not stand up to the stresses of hard use. ECS Exact-Fit stainless reinforced clutch lines provide more confident and dependable shifting by maintaining consistent line pressure, long lasting corrosion resistance, and increased protection from failure. These lines are reinforced with braided stainless steel mesh, affording superior expansion resistance. This resistance to expansion creates a firmer pedal, and a more direct clutch pedal feel. The signature red polymer coating provides additional protection from the elements and abrasion.

This particular stainless steel clutch line fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix M3
1988 E28 BMW M5
1987-1989 E24 BMW M6 

ARP Flywheel Bolts are a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated, ensuring complete heat penetration, to increase the clamping load up to 200,000 psi. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best bolts we've found and we highly recommend them in any and all applications. 

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMW Engines: 
M20 2.5L

Eliminate the factory clutch delay valve and enjoy faster, more precise clutch engagement with the ECS Clutch Delay Valve (CDV) Removal Tool Kit. Designed for F and G-Chassis manual BMWs, this kit makes removing the hydraulic restrictor safe, simple, and reliable, no slave cylinder removal required.

Most modern BMWs come from the factory with a plastic slave cylinder featuring a CDV, intended to smooth engagement and reduce driveline shock for less experienced drivers. In practice, this restrictor can dull pedal feedback, slow shifts, and increase clutch wear. Removing it restores the sharp, direct clutch feel that BMW enthusiasts expect.

Key Benefits:

Faster, more predictable clutch engagement
Sharper pedal response and connected driving feel
No need to remove the slave cylinder
Tool Design:

Machined from durable 304 stainless steel
Includes precision removal and insertion tools
Knurled grip for easy handling
Built-in depth and angle control protects internal surfaces and ensures proper grommet alignment
Removal and Installation:

Disconnect the Clutch Line
Remove the clutch line from the slave cylinder to access the factory clutch delay valve.
Remove the Restrictor Plate
Thread the removal tool into the center of the small grommet. Once engaged, carefully pull the tool to remove the grommet and restrictor plate. The small rubber sealing O-ring will come out along with the plate.
Reinstall the O-Ring
Place the rubber O-ring onto the installation tool. Insert the tool into the slave cylinder to properly seat the O-ring in its original position.
Reconnect and Bleed the Clutch
Reattach the clutch line, add fluid, and bleed the system according to your manufacturer’s instructions.
Enjoy Enhanced Clutch Feel
With the delay valve removed, your clutch now engages faster and more predictably, giving your manual transmission the sharp, connected feel it was designed for.

Working in collaboration with Competition Clutch, the up and coming German automotive performance company DKM has released a new line of high quality clutches made to satisfy your stock and modified performance needs! If you're having problems keeping power to the wheels, DKM has the solution. Their design, using high-grade materials, gives you increased strength and heat tolerance preventing wear and fade, ensuring increased torque capacity, quicker shifts, and longer clutch life.

Tracking your vehicle is all fun and games until you start burning through clutches as fast as you can afford to replace them. To end this cycle, the MS Twin Disc Clutch Kit is designed to hold up to 100 to 200% more torque capacity and provide you with a much-improved clutch life span. The two organic disc setup provides additional contact surface areas to more evenly distribute pressure and heat for both a boost in performance and wear prevention.

Kit Contents:
Pressure Plate
Two Organic Discs
Steel Single Mass Flywheel
Pilot Bearing/Bushing and Throw-out Bearing (when applicable)
Alignment Tool

BMW Lightweight Flywheels

• Crafted with precision from Forged Chromium-Molybdenum Steel
• Perfect fitment and finish for hassle-free installation
• Utilizes leading-edge Solidworks 3D CAD and Cosmos FEA software for design
• Advanced geometry minimizes drivetrain losses, offering 1-2% more power to the ground
• Precision balanced to exceed 12,000rpm for utmost reliability
• Made from imported Japanese SAE 4140 Steel
• Forged, double-tempered, and super sub-zero treated for unsurpassed toughness
• Proprietary Nitride surface treatment enhances surface hardness

BMW E39 M5 South Bend Stage 2 Daily Clutch Kit provides a powerful, durable upgrade for the E39 M5, combining exceptional torque capacity with daily drivability. Turner Motorsport offers this clutch kit, designed to handle high horsepower modifications with ease. Featuring a heavy-duty pressure plate and high metal-content organic disc, this clutch system delivers double the friction of a stock lining and a burst strength up to 12,000 RPM.

Ideal for both daily use and moderate race conditions, this Stage 2 clutch kit is rated to manage up to 440 lbs/ft of torque. The solid-hub center section is optimized for compatibility with the OE dual-mass flywheel, ensuring a smooth, reliable driving experience while maintaining a nearly stock pedal feel.

• Heavy-Duty Pressure Plate: Increased clamp load for superior torque handling with minimal change in pedal pressure
• High Metal-Content Organic Disc: Provides double the friction coefficient and enhances rotational strength, rated up to 12,000 RPM
• Smooth Daily Drivability: Near-stock pedal feel, perfect for street driving and moderate racing
• Solid-Hub Center Design: Seamlessly integrates with the OE dual-mass flywheel for optimal performance
• Torque Capacity: Rated to manage up to 440 lbs/ft, ensuring dependable strength for modified power levels

Recommended for daily, street, and moderate race applications.

Lightweight flywheel and upgraded clutch kit for improved throttle response, acceleration, and clutch feel - the perfect setup for daily-driven vehicles with up to 400 Ft/lbs of torque.

This performance clutch and flywheel kit utilizes an upgraded ECS E34 M5 clutch kit with their in-house engineered flywheel to fit all M5x and S5x motors with a 5-speed transmission. By eliminating the dual-mass flywheel and replacing it with a single-mass you are able to eliminate the slack and extra weight of the flywheel for a quicker throttle response and acceleration. Their upgraded clutch kit utilizes all the best features of the original M5 clutch with an upgraded pressure plate and clutch disc, with the new clutch you have a better, more engaged clutch pedal feel, engagement, and longevity.

Whether you're replacing a worn-out clutch or upgrading for increased power handling, this E34 M5 clutch and flywheel kit offers a reliable solution for enhanced pedal feel, power capacity, and overall driving satisfaction.

Paired with a modified geometry flywheel, the E34 M5 style clutch is ideally suited for most E36, E46, and others using the same powertrain. It checks all the boxes for essential clutch replacement features. While some aftermarket options may address slipping issues and worn-out clutches, they often sacrifice pedal feel, providing little to no resistance. A soft clutch not only kills the driving experience of your BMW but also reduces confidence when pushing the car to its limits.

On the contrary, you might be in the market for an upgraded clutch to handle your modified engine/forced induction builds. You go from an OE or aftermarket clutch option that has a lackluster and soft pedal feel to the complete opposite side of the spectrum, a very stiff clutch that grabs like an on-and-off switch making the clutch a pain almost undrivable on the street resulting in your favorite car turning into your least favorite car to drive.

The E34 M5 clutch and flywheel kit balances performance with practicality, ensuring a satisfying driving experience whether you're maintaining your BMW or preparing it for increased power demands.

Kit Contents:

Single Mass Flywheel - E34 M5 Clutch Geometry
Performance Clutch Disc and Pressure plate
Throw-out Bearing
Pilot Bearing
Clutch Alignment Tool
Flywheel Bolts - Qty 8
Pressure Plate Botls - Qty 6
Clutch features:

Torque Capacity (Crankshaft):
400 Ft / Lbs
Clutch Disc:
240mm Full face, performance organic friction material with integrated copper for enhanced heat dissipation and a long component life
OE-like friction backing plate design for smooth engagement with dual-stage damping springs to reduce gear noise and driveline chatter, and for smooth engagement
Pressure Plate
Increased clamp force over OEM, rated at 1,729lbs of pressure
Flywheel features:

Eliminates factory dual mass
Improved throttle response
Improved acceleration
Hardened 4140 Chromoly Steel
Designed for use with any E34 M5 pressure plate and clutch for OE-type clutch feel
Weighs in at just 16.5lbs vs Factory Dual Mass - 25.3 lbs
SFI certified
Fitment:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i (5-speed)