Turner Motorsport BMW Camber / Caster Kits

Whether you need a camber change or you are looking for more adjustment with your camber plates, you can change your camber by shimming the strut and spindle with the TMS bolt kit. There are some things to take into account with this kit so please read the installation tips below. An alignment is strongly recommended after installing this kit.

Click here for installation instuctions.

This item fits the following BMWs:
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2006-2008 E85 E86 BMW Z4 M Roadster M Coupe

These camber plates are perfect for the enthusiast owner who wants a high quality design with a motorsports background. Knowing a full race kit on the street is not often the best option, we took the best features from the Race Camber Plates and incorporated them into a fresh Street design -

• preserves the correct E46 M3 geometry
• separate sliding camber and caster adjustments
• maximum shock travel
• light weight
• durable materials
• large surface area
• ease of use

The Turner E46 M3 Street Camber Plates are the most advanced design on the market. These are designed specifically for the E46 M3 - no shortcuts or cookie-cutter components. We started with a fresh design to make these very user friendly and easy to install and set up. The E46 M3 front suspension has unique geometry and the strut is mounted at an angle that can put significant side loading on the strut shaft if it's not located properly. The location and angles for the main bearing were carefully engineered to allow the proper motion ratio and strut angles during adjustment. This greatly reduces bending forces on the strut itself which improves performance and longevity. By designing for one chassis we're able to focus on what works best in that application - proper fitment and operation without unnecessary adapters, easy-to-use camber and caster adjustments, and an intelligent modular design.

For street use we added a pliable urethane bushing to absorb vibration and a special base design that works with the factory radial bearing and spring perch. The radial bearing allows the spring to rotate instead of twisting and binding. By re-using the factory radial bearing we can keep the assembled stack height lower for maximized shock travel. It's also a commonly-available item that you can get from any BMW dealer at a low price. All of the things that make it work well in the factory application carry over to our design. You can use our camber plates with a stock sized spring, 60mm, or 2.5" springs. Use your stock spring perch/bearing with stock-sized springs. The 60mm and 2.5" upper spring perches are sold separately. The beauty of our design is that you can use the factory radial bearing with any of these springs.

Another important feature of the Turner Camber Plates is the size of the upper plate. Our plates have a very large surface area to better spread strut forces through the strut tower. A smaller upper plate, like those found on competitor's kits, will localize strut forces and contribute to strut tower deformation ('strut tower mushrooming'). This is a very important feature especially as these cars get older and spend more time on the track. Deformed strut towers are a serious performance and safety concern and our camber plates are properly designed to handle the loads. The factory strut reinforcement plates are not required with our camber plates (but you can use them if you want to).

Since this design is specific to the E46 M3, we can build it with the bare minimum of adapters and extra hardware. This not only cuts down on confusion but makes it easier to assemble and operate. We use the correct-sized bearing for the 16mm strut shaft; no sleeves or bearing adapters required. The original tapered lower mount support and a small stainless steel spacer from our kit are all that's required to install. We have used our camber plates with most of the major strut manufacturers on the market - stock Sachs/Boge, Bilstein, Koni, H&R, ST, and KW. Our camber plates work with any strut that is designed to accept the factory strut mount.

Click here for installation instructions.

This item fits the following BMWs:
2001-2006 E46 BMW M3

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should. 

Increasing the negative camber of your E36 M3 will reduce understeer and prolong the life of your tires when used on the track. These plates simply bolt on top of the factory upper strut bearings and increase negative camber by .5 or 2 degrees, depending on the holes you chose to use. We maximized the available camber available with a stock-diameter sized spring. Vehicle height in the front will be raised by .25”. We also added material to the surface area of the mount to increase stiffness of contact area, therefore reducing the strut tower deformation and increasing the strength of the strut towers. Fixed mount camber plates are legal for many racing and autocross classes. These are the perfect camber solution when adjustable plates are not allowed in your class. 

This item fits the following BMWs: 
1996-1999 E36 BMW M3 
1998-2002 E36/7 BMW Z3 M Coupe M Roadster

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

Increasing the negative camber of your 1995 E36 M3 will reduce understeer and prolong the life of your tires when used on the track. These plates simply bolt on top of the factory upper strut bearings and increase negative camber by 2 degrees. We maximized the available camber available with a stock-diameter sized spring. Vehicle height in the front will be raised by .25". We also added material to the surface area of the mount to increase stiffness of contact area, therefore reducing the strut tower deformation and increasing the strength of the strut towers. Fixed mount camber plates are legal for many racing and autocross classes. These are the perfect camber solution when adjustable plates are not allowed in your class.

Instructions for Turner 1995 E36 M3 Front Fixed Camber Plates

This item fits the following BMWs:
1994-1995 E36 BMW M3

Looking for upgraded lower control arms that don't limit adjustment capabilities like the OE control arms? These Turner Performance Lower Control Arms may be exactly what you need! These CNC'd billet aluminum control arms allow you to adjust roll center, camber, and track width easily and lock in your adjustments securely.

The construction of these control arms allows for significant weight savings, reducing unsprung weight, while maintaining high levels of strength that is up to track use and abuse. Instead of using traditional jam nuts, these Turner Control Arms utilize a pinch bolt and rotating clamp design that allows high clamping forces to lock in track width and camper specifications without making it difficult to keep bearings properly aligned. Stainless steel spacers are included to enable roll center correction for lowered vehicles. To further improve control arm operation over the OE design, these control arms use FK rod ends and high misalignment solid spherical bushings to get rid of binding and flex.

Features:

Lightweight Aluminum, Titanium, Chromoly and Stainless Steel construction
Correct ball joint angle for full articulation
Clamp design allows for easy access to lock down your alignment settings
Low friction 3-piece Teflon lined FK spherical bushings and Heim joints/rod ends
Multiple size stainless steel roll center spacers for precise adjustment

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

These fixed steel camber plates for your E30/E24/E28 will add 3/4 degree of negative camber and will reduce understeer during hard cornering and save the outside edge of your tire. These plates mount to the top of the upper strut bearing and relocate the top of the strut further in. Combine these with the BMW offset upper strut bearings for even more negative camber. These are the perfect camber solution when adjustable plates are not allowed in your class. We used these in our ultra-successful J-Stock suspension as they maximize the available camber in the tire well when using the large, stock-diameter springs.

Instructions for Turner E30 Front Fixed Camber Plates

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is M3