Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:​

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

A beautiful addition and durable upgrade for your engine

Tired of staring at that bright red plastic oil dipstick? Waiting for a way to add a nice touch to your engine bay without going over the top? ECS Tuning is proud to announce the billet aluminum oil dipstick! Designed to OE specifications with an easy-to-read fill line, offered in three different finishes. Available in black, polished, or clear anodized, we have an offering for every type of enthusiast. Not only does it look better, but also performs better. Because of the durability, it is easier to insert than the factory ribbon dipstick. So, no more fighting with your dipstick to re-install it.

ECS Tuning presents magnetic drain plugs tailored for your BMW, equipped with a permanently mounted magnet to trap ferrous metal suspended in your oil. These plugs capture tiny particles, typically evading the oil filter, resulting in a cleaner engine. Over time, this saves your bearings and oil pump from unnecessary wear. Crafted from robust 7075-T6 aluminum, the ECS Tuning M12 magnetic drain plug boasts 80% more strength than the common 6061 aluminum.

• Permanently mounted magnet for metal particle trapping
• Cleaner engine and extended bearing life
• 7075-T6 aluminum construction for superior strength
• Captures metal particles from wearing or rebuilt engines
• Ideal for normal wear of reciprocating parts
• Torque to 18ft-lbs using a 17mm socket, like your stock drain plug

Upgrade your MINI with the M7 Oil Catch Can Kit__xxSTARTxx__/h1

The newly updated R55 through R57 Oil Catch Can kit for MINIs equipped with the N14 engine comes with a "designed-to-fit" stainless steel bracket, mounting hardware and pre-assembled hoses. Installation is super easy...no drilling and no special tools are needed. NOTE: This kit has been redesigned to fit on the firewall directly behind the outlet of the airbox. It uses the factory tab located on the firewall."Forum experts and social hysteria" say an OCC is not needed but we beg to differ. Why do so many MINI owners suffer from carbon buildup on their intake valve? The answer is oil being recycled through the intake tract to be burned. With the M7 Oil Catch Can, your MINI Cooper's engine will be protected from excessive oil and hydrocarbon buildup which leads to performance-hindering oil film and sludge along your intake tract, on your engine control sensors and on your engine's intake valves. Because the 2007 & up MINI is direct injection the intake valves do not benefit from the cleaning action provided by the gasoline as in older port injection engines. Now all the oil blow-by burns onto the intake valves and builds up into a flow choking hydrocarbon mess. The end result is loss of power and a very expensive repair bill. This oil film & sludge can appear in other critical places throughout the engine-- such as the intercooler-- where clean surfaces are critical for maximized heat transfer and on your MAF sensor (Mass Air Flow) where the film will cause the sensor to send a false signal to your ECU killing performance.

By capturing excess oil vapor and particles, the M7 Oil Catch Can ensures that oil film and sludge will not become a factor in your vehicle's performance. If you don't think your engine is pumping oil back through your intake system, remove the breather tube and look at all the oil!. The breather tube connects directly to you intake hose and directs this oily mess back through your engine to be burned.

Now with our exclusive "Exact-Fit" pre-assembled hose kit and brackets installation is super-easy.

Features:

• Pre-assembled hose assemblies.
• Stainless steel bracket and mounting hardware
• Eliminate intake tract oil contamination and intake valve damage.
• Prevent pre-mature sensor failure
• Keep engine performance at peak levels
• Billet Aluminum Construction
• Bright Black Anodized Finish
• Laser Etched M7 Logo

The M7 Oil Catch Can is not only functional is a work of automotive performance ART! It is CNC machined from billet aluminum and adds a sharp look to your engine compartment.

All hoses, brackets, clamps, necessary fittings and easy to follow detailed step-by-step instructions are available on this page in .PDF format. The design includes an oil drain plug and an easy to view sight tube which indicated the oil level within the can. The hoses are high quality "Made in the USA" automotive grade designed to withstand the rigors of the under-hood environment and to not degrade when exposed to oil. Beware of other "low cost" catch can systems that use silicone hoses because oil and silicone are not compatible. Silicone hoses will will eventually deteriorate and make an absolute mess of your engine compartment.

Enhance Your Mini's Drivetrain Longevity with ECS Tuning's Magnetic Plugs

Safeguard your Mini's drivetrain by using ECS Tuning's Magnetic Plugs, meticulously designed to eliminate abrasive metal particles from your fluid. These plugs, featuring permanent magnets, effectively attract and retain tiny abrasive and ferrous metal particles, preventing their circulation within the lubrication systems.

Various conditions, including normal wear of moving parts, inadequate post-machining flushing, casting flaws, or stress-induced component breakdown, can introduce metal particles. ECS Tuning's Magnetic Plugs are the solution, ensuring protection for crucial drivetrain components by capturing these particles.

• Removes abrasive metal particles for improved drivetrain longevity
• Engineered with permanent magnets for effective particle capture
• Guards against wear caused by metal particles in the lubrication system
• Includes 10 copper crush washers for replacement during oil service

M7 Oil Catch Can Kit for MINIs

Newly Updated Kit for Improved Engine Performance

The newly updated R55 through R59 Oil Catch Can kit for MINIs equipped with the N16 or N18 engine comes with a "designed-to-fit" stainless steel bracket, mounting hardware, and pre-assembled hoses. Installation is super easy... no drilling and no special tools are needed.

Note: This kit has been redesigned to fit on the firewall directly behind the outlet of the airbox. It uses the factory tab located on the firewall.

Why You Need an Oil Catch Can

"Forum experts and social hysteria" may say an OCC is not needed, but we beg to differ. Many MINI owners suffer from carbon buildup on their intake valve due to oil being recycled through the intake tract to be burned.

With the M7 Oil Catch Can, your MINI Cooper's engine will be protected from excessive oil and hydrocarbon buildup, which leads to performance-hindering oil film and sludge along your intake tract, on your engine control sensors, and on your engine's intake valves.

This oil film & sludge can appear in other critical places throughout the engine, such as the intercooler and the MAF sensor (Mass Air Flow), where clean surfaces are critical for maximized heat transfer and engine performance.

Features and Benefits

• Prevents intake tract oil contamination and intake valve damage
• Prevents premature sensor failure
• Keeps engine performance at peak levels
• Increases flow area by 77% for improved oil separation
• Includes billet aluminum oil catch can with coalescing oil separation technology and integrated dipstick
• Comes with two molded oil-resistant silicone hoses with STS technology (available in Red or Black)
• Includes installation hardware kit and printed instructions
• 100% carbon fiber housing with CNC machined billet aluminum top and bottom

Easy Installation

With our exclusive "Exact-Fit" pre-assembled hose kit and brackets, installation is super-easy. All hoses, brackets, clamps, necessary fittings, and easy-to-follow detailed step-by-step instructions are included. An oil drain plug and an easy-to-view sight tube are also provided, allowing you to monitor the oil level in the can.

Beware of other "low-cost" catch can systems that use silicone hoses, as oil and silicone are not compatible and silicone hoses will eventually deteriorate, causing a mess in your engine compartment. Access Secret Premium Dashboard