M7 Oil Catch Can Kit for MINIs

Newly Updated Kit for Improved Engine Performance

The newly updated R55 through R59 Oil Catch Can kit for MINIs equipped with the N16 or N18 engine comes with a "designed-to-fit" stainless steel bracket, mounting hardware, and pre-assembled hoses. Installation is super easy... no drilling and no special tools are needed.

Note: This kit has been redesigned to fit on the firewall directly behind the outlet of the airbox. It uses the factory tab located on the firewall.

Why You Need an Oil Catch Can

"Forum experts and social hysteria" may say an OCC is not needed, but we beg to differ. Many MINI owners suffer from carbon buildup on their intake valve due to oil being recycled through the intake tract to be burned.

With the M7 Oil Catch Can, your MINI Cooper's engine will be protected from excessive oil and hydrocarbon buildup, which leads to performance-hindering oil film and sludge along your intake tract, on your engine control sensors, and on your engine's intake valves.

This oil film & sludge can appear in other critical places throughout the engine, such as the intercooler and the MAF sensor (Mass Air Flow), where clean surfaces are critical for maximized heat transfer and engine performance.

Features and Benefits

• Prevents intake tract oil contamination and intake valve damage
• Prevents premature sensor failure
• Keeps engine performance at peak levels
• Increases flow area by 77% for improved oil separation
• Includes billet aluminum oil catch can with coalescing oil separation technology and integrated dipstick
• Comes with two molded oil-resistant silicone hoses with STS technology (available in Red or Black)
• Includes installation hardware kit and printed instructions
• 100% carbon fiber housing with CNC machined billet aluminum top and bottom

Easy Installation

With our exclusive "Exact-Fit" pre-assembled hose kit and brackets, installation is super-easy. All hoses, brackets, clamps, necessary fittings, and easy-to-follow detailed step-by-step instructions are included. An oil drain plug and an easy-to-view sight tube are also provided, allowing you to monitor the oil level in the can.

Beware of other "low-cost" catch can systems that use silicone hoses, as oil and silicone are not compatible and silicone hoses will eventually deteriorate, causing a mess in your engine compartment.

Oil venting and circulation continues to be a problem on BMW engines and now even more so on the turbocharged N54 and N55 engines. The existing stock system does a very poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. We're seeing a lot more 135 and 335 cars with drivability and performance issues because oil has sneaked by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media blasting of the intake valves to strip away the oily buildup we have seen.

Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. The Burger Tuning oil catch can is the best we have seen so far. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine.

The BMS Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). The BMS OCC also has a factory-like appearance. Since BMS designed their catch can from scratch they can guarantee it fits and performs correctly for the N54/N55 engine, unlike other catch cans on the market that are poorly retrofitted from other applications and under-sized for the N54 engine.

Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles

BMS Oil Catch Can Features:
+ Increases air intake efficiency
+ Promotes engine longevity
+ Double-baffled design allows excellent air/oil separation
+ Large In/Out ports (no tapered sizes that slow flow)
+ Stealth mounting on cooler side of engine bay (promotes condensation of oil to vapor)
+ Anodized black lightweight aluminum
+ N54 version mounts out of sight under the cowl
+ Made in USA with a lifetime guarantee

Oil venting and circulation continues to be a problem on BMW engines and now even more so on the turbocharged N54 and N55 engines. The existing stock system does a very poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. We're seeing a lot more 135 and 335 cars with drivability and performance issues because oil has sneaked by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media blasting of the intake valves to strip away the oily buildup we have seen.

Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. The Burger Tuning oil catch can is the best we have seen so far. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine.

The BMS Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). The BMS OCC also has a factory-like appearance. Since BMS designed their catch can from scratch they can guarantee it fits and performs correctly for the N54/N55 engine, unlike other catch cans on the market that are poorly retrofitted from other applications and under-sized for the N54 engine.

Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles

BMS Oil Catch Can Features:
+ Increases air intake efficiency
+ Promotes engine longevity
+ Double-baffled design allows excellent air/oil separation
+ Large In/Out ports (no tapered sizes that slow flow)
+ Stealth mounting on cooler side of engine bay (promotes condensation of oil to vapor)
+ Anodized black lightweight aluminum
+ N54 version mounts out of sight under the cowl
+ Made in USA with a lifetime guarantee

This item fits the following BMWs with the N54 twin-turbo engine:
2008-2010 E82 BMW 135i
2007-2010 E9X BMW 335i 335xi
2006-2010 E60 BMW 535i 535xiThis item fits the following BMWs with the N54 twin-turbo engine:
2008-2010 E82 BMW 135i
2007-2010 E9X BMW 335i 335xi
2006-2010 E60 BMW 535i 535xi

CSF is one of the premier cooling product specialists available on the market today. One item that is often overlooked is the oil cooler. Luckily CSF has taken up the task of upgrading the oil cooler as well. If the oil runs too hot, it can lead to a reduction in wear protection and damage to the head, block, or the turbo system. This unit has 17 cooling tubes in the front with anther 6 in the rear of the cooler and still fits in the stock location without any issues.

Fits the following BMW:
2016+ F87 BMW M2

The factory E9X oil filter housing cap is made of plastic which, by nature of the material, dissipates heat poorly and is prone to failure over repeated heat cycles. By contrast to the OEM unit, our cap is constructed from 6061-T6 aircraft-grade aluminum which promises two functional benefits: greater longevity and cooler running throughout its life cycle.

So too will the oil itself benefit: By getting your oil up to temperature quickly, but tangentially evacuating excess heat, the aluminum oil filter housing cap will help your fluid operate within its working range while effectively preventing thermal breakdown.

Each cap has been meticulously manufactured on a DMG Mori 5-Axis with specially sourced tooling to achieve some of the cap's intricate details. Anodized, the housing cap’s details are happily preserved but offer up a valuable way for an enthusiast to express their individuality. Four colors are available at launch to maximize choice: Ferrari Red, Royal Blue, Hard Coat Clear, and Hard Coat Black.

Appropriately, our latest livery box echoes a Gulf theme—echoing our motorsport intent and ties to the culture that has inspired us to create from the beginning.

Product Details:

Compatible with S65-equipped BMW vehicles Plug-and-play replacement for OE plastic cap CNC precision machined from 6061-T6 aerospace aluminum Improves heat dissipation and increases cap longevity Four anodizing options: Ferrari Red, Royal Blue, Hard Coat Clear, & Hard Coat Black Proudly made in USA