The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

This coilover kit fits the following BMWs:
2008+ E82 BMW 128i 135i
2006+ E90 BMW 325i 328i 330i 335d 335i
2007+ E92 BMW 328i 335i 335is
2007+ E93 BMW 328i 335i

M7 Strut Reinforcement Plates 53-510101 are the ultimate solution for MINI owners facing the common issue of strut tower mushrooming caused by heavy impacts from shocks and low aspect ratio tires. Over time, MINI's shock towers can develop a convex shape, disrupting suspension alignment and leading to a noticeable pull to one side. The M7 Strut Reinforcement Plates (SRPs) address this problem by reinforcing the sheet metal and shock top plate, creating a durable surface that resists bending, even during hard impacts.

Designed specifically for the R50 Base Model Cooper, the R52 Convertible, and the R53 Cooper S, these SRPs are an essential upgrade for any MINI enthusiast. Constructed from CNC machined billet aluminum and black anodized for durability, the 1/2" (13mm) thick plates cover the entire surface of the strut tower, distributing loads evenly and providing peace of mind.

Whether you drive your MINI daily or push it to the limits on the track, M7 Strut Reinforcement Plates offer a cost-effective preventative measure against expensive suspension repairs. Easy to install in less than 20 minutes, the SRPs use the stock nuts for mounting and come with instructions that also guide you through fixing existing mushrooming.

• Prevents strut tower mushrooming
• Constructed from CNC machined billet aluminum
• Black anodized for long-lasting durability
• Covers the entire strut tower surface
• Designed for R50, R52, and R53 MINI models
• Easy installation with stock nuts
• Made in the USA

If you are concerned about strut tower mushrooming and looking for improved handling, the M7 Strut Tower Brace (STB) is the solution. This is the ONLY strut tower brace on the market that features anti-mushrooming technology.

Repeatedly, we've heard the same complaint: strut towers mushroom after heavy impacts from shocks and low aspect ratio tires. Initially, the shock towers take on a barely visible convex shape, but if compared to the original sheet metal, you'll find the horizontal plane has moved as much as 3/8" upwards, making alignment nearly impossible.

This issue often shows up as a slight pull to the left or right, depending on which strut tower is affected. The M7 Strut Tower Brace's end mounting plates solve this problem by sandwiching the sheet metal and shock top plate, creating a reinforced surface that won't bend, even during hard impacts.

The M7 STB features 1/2" (13mm) thick end plates that add extra strength to the strut towers, preventing mushrooming and potentially costly repairs. The cross brace significantly improves handling by adding torsional stiffness to the front body structure, helping keep your tires planted and pointed in the direction you want to go, especially during hard turns. Machined from billet aluminum and matte black powder coated, the M7 Strut Tower Brace boasts a durable black finish that looks great and won't chip or oxidize.

We have customers who won't drive their new MINI off the lot without one and dealers that sell every new MINI with either the M7 Strut Reinforcement Plates or the M7 Strut Tower Brace.

Concerned about clearance? No worries. The M7 STB profile is designed to clear both stock and aftermarket cold air intakes and ECUs. Its modular design allows easy access to the oil filter or any other accessories that might normally be blocked and require removal of the entire brace.

Installation is a snap (often taking less than 20 minutes)! No need for new nuts—the brace uses the three stock nuts on each side. Installation instructions are available online by clicking the "INSTALLATION" link on this page.

The M7 Strut Reinforcement Plates and the M7 Strut Tower Brace are two separate products that address strut tower mushrooming (you only need one or the other).

If your MINI is mainly a daily driver, the M7 Strut Reinforcement Plates are sufficient. If you have performance driving in mind, the M7 Strut Tower Brace is what you're looking for!

Please note:

• You cannot buy the SRPs and attach the cross-bar at a later time.
• The brace does not directly fit on the R50 and R52 Non-"S" Cooper due to limited hood clearance of the non-supercharged cars. It will fit but may push up on the hood slightly, requiring molding or cutting of the hood insulation after installation.
• Trimming of the underhood insulation material may be required to fully clear this brace. This is a very tight space.

Enhance your BMW's handling with M7 MAXX-G Adjustable Swaybar Endlinks designed for lowered or raised MINIs. Crafted from forged SAE 4340 alloy steel, these endlinks offer superior strength and symmetry in cornering performance, allowing bind-free suspension travel and improved chassis balance. The adjustability feature ensures proper alignment, maximum grip, and neutralized sway bars for consistent balance in left and right-hand turns.

Benefits:

• Superior strength with forged alloy steel construction
• Symmetric cornering performance enhancement
• Bind-free suspension travel and better alignment
• Adjustable length for precise chassis tuning
• Corrosion-resistant black anodized finish
• Proudly made in the USA

M7 Speed Suspension Product for Generation 1 MINI Cooper (R50-R53)

M7 Speed introduces a unique suspension product for the popular Generation 1 MINI Cooper models R50 through R53. These affordable vehicles are becoming the choice for many entry-level modifiers in the German performance car segment, and this product is great for Rally Cross.

Engineered to convert the mild-mannered MINI into a more capable and versatile daily driver, this kit is perfect for spirited adventure motoring, weekend overlanding, living off the grid, or navigating pothole-riddled urban streets. The M7 Speed 2" Lift Kit lifts the MINI 2" higher, plus an additional lift from larger diameter tires (up to an extra 1.5"). No additional modifications are required—just bolt it in, realign, and enjoy! Enhance your MINI with aftermarket wheels and larger tires for a more durable, practical, and enjoyable vehicle.

Stage 1 Kit Includes:

• 2" Lift Kit with high-strength assembly hardware (2 front riser blocks, 2 rear riser blocks)
• MAXX-G Heavy Duty Adjustable Front Sway Bar Links
• Hardware kit with high-strength proper length bolts and new locking nuts

Features:

• Engineered using 3D CAD software and finite element simulation for proper fitment and safe performance
• CNC laser-cut parts
• Lightweight fabricated steel design
• Black urethane powder coated for corrosion protection and a quality appearance
• Easy bolt-on installation with all new high-strength hardware and installation instructions

MAXX-G Adjustable Sway Bar:

• Enhances cornering performance, bind-free suspension travel, better suspension alignment, and overall chassis balance
• Sealed and permanently lubricated forged steel ball stud & socket ends for easy installation
• Military grade aluminum adjuster sleeve with opposing RH & LH threads for simple length adjustments
• Replicable link ends for easy maintenance

M7 Speed is the world leader in MINI adventure motoring, overlanding, and ultimate performance products. Known for exceptional customer service and product innovation, the company is dedicated to engineering and producing high-quality, easy-to-install aftermarket performance products. M7 Speed is located in Mooresville, North Carolina, also known as Race City USA.

Improve Your MINI's Grip with the M7 Rear Chassis Brace!

Enhance your MINI's handling by stiffening its chassis with the newly redesigned M7 Rear Chassis Brace. This upgrade is crucial for maximizing tire grip, allowing your suspension components—such as springs, shocks, and sway bars—to function optimally and keep your tires in better contact with the ground, resulting in improved grip.

• Enhanced Handling: Achieve better handling performance on both the street and the track by adding the M7 Rear Chassis Brace to your MINI's chassis.
• Triangulated Design: The fully triangulated design ensures maximum stiffness and stability, providing enhanced control during cornering and maneuvering.
• Lightweight Construction: Crafted from lightweight materials used in race car construction, the M7 Rear Chassis Brace adds rigidity without compromising your MINI's agility.
• Easy Installation: Designed for hassle-free installation, this brace can be easily mounted to your MINI's chassis with basic hand tools, allowing you to hit the road or track in no time.

Upgrade your MINI's chassis with the M7 Rear Chassis Brace and experience a significant improvement in grip and handling. Access Secret Premium Dashboard