BMW Engine Parts

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This is the current replacement for some BMW 6 and 8-cylinder engines built in the late 2000s and after. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed below. It's listed as a replacement coil for N20, N55, and S55 engines. In March 2015 BMW approved it for N51/N52 engines. This part number replaces the previous BMW part number 12137594937 for the cars listed below.

Sold per coil. Includes boot and connector.

BMW S65 BE Bearings Connecting Rod Bearing Upgrade Set is designed to address the known flaws in the factory BMW rod bearings, particularly for the S65B40 engine. Manufactured by Clevite to BE Bearing specifications, this set provides a crucial upgrade with its enhanced materials and design, ensuring improved performance and durability.

The original BMW bearings have minimal clearance, which leads to premature wear and potential engine failure. This upgrade replaces the tin-aluminum factory bearings with a superior silver-oxide-coated tri-metal "F" series design. The new bearings can handle 30% more load, offer better performance in low oil conditions, and are more forgiving of foreign particles in the oil. Designed specifically for BMW S65 engines, these bearings provide optimal performance for high-horsepower applications.

• Designed specifically for BMW S65B40 engines
• Silver-oxide coating withstands 30% more load capacity
• Improved performance under low-oil and boundary conditions
• Stronger backing material for enhanced durability
• Corrects factory BMW rod bearing clearance issue
• Ideal for high-horsepower applications and factory 10W60 weight oils
• Complete set for 8 cylinders, ready for installation

Fits the following BMWs:

• 2008-2013 E9X BMW M3 (S65)

Designed and manufactured by Clevite to BE Bearing specifications.

These bearings replace the factory BMW rod bearings. The original BMW bearings have too little clearance, which leads to premature bearing wear and can cause early engine failure.  Furthermore, the factory BMW bearings are made from tin-aluminum which are 5-times harder than a softer lead-copper bearing design. A softer bearing is better for your engine and more tolerant of foreign particles suspended in your oil.

These BE Bearings feature a state-of-the-art Clevite Tri-Metal design with the Clevite Tri-Armor(tm) coating.

• Lead-copper design for greater durability and easy tracking with oil analysis like Blackstone (recommended).
• Designed with extra clearance to "fix" the BMW rod bearing design flaw.
• Designed for use with factory 10W60 weight oils.
• Tri-Armor coated for low conditions during cold start
• Ideal for start-stop vehicles
• Applicable for BMW engines S85B50
• Standard Clearance
• Sold as complete set (10-cylinders)

Fits the following BMWs:
2005-2010 E60 BMW M5
2005-2010 E63/64 BMW M6

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

Vargas Turbo has done it again. They've made it even easier for you to get your car back on the road and running right again with your new turbos. They've put together an install kit containing all the components you need to get your new turbos installed properly and efficiently. This means you can get your car back on the road faster and enjoy your new turbos! 

Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.