BMW Engine Parts

The Crankshaft Position Sensor measures the speed and position of the crankshaft to determine the proper fuel and timing requirement for the best performance.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Pulse Generator
This item fits the following BMW Chassis:
E36 M3,E36

Fits BMW Engines including:
M50,S50

When replacing fuel injectors, there are some vital components that have to be replaced at the same time that are included in this kit.

Kit includes:

6 Genuine BMW injector seals
6 Genuine BMW de-coupling elements

The VANOS system on your N51, N52, and N54 engine controls the valve timing inside the engine. The system is hydraulically operated based on instructions from the engine computer. It's very complex and BMW has not yet perfected the system. The VAN0S solenoid is the actuator that takes instruction from the ECU and activates the VANOS unit on the front of the engine. When the solenoid is failing (or failed) you can end up with a rough running engine, misfires, bad fuel economy, lack of power, and more. It should trigger multiple fault codes and a check engine light for misfires, camshaft control, VAN0S solenoid, boost pressure control, and maybe others. It's important to thoroughly troubleshoot fault codes but VAN0S solenoids are a known issue with these engines.

The VANOS solenoids are located on the front of the engine and may be replaced without removing many other components. In some cases, you may be able to remove the suspect one, clean it, reinstall, and reset your fault codes. If your fault codes come back it's a strong indication that a replacement is required. Or you can buy the new solenoid and replace instead of doing the work twice.

VANOS solenoid for the intake and exhaust are the same part number. Order 2 if you want to replace them both.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

We recommend replacing the solenoid sealing gaskets as well when replacing the solenoid. You can find these under T#363393

This item fits the following BMWs:
2008-2012 E82 BMW 128i 1M Coupe
2008-2010 E82 BMW 135i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335is - Sedan
2006-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335is - Coupe
2007-2010 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2007-2010 E93 BMW 335i - Convertible
2006-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive
2011 F10 BMW 528i
2006-2010 E83 BMW X3 3.0i X3 3.0si
2007-2013 E70 BMW X5 3.0si
2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009-2011 Z4 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This is the Genuine BMW ignition coil that is the current replacement for most BMW V10 S85 engines.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

This item fits the following BMWs:
2006-2010 E60 BMW M5
2006-2010 E63 BMW M6

Feeds oil to the VANOS unit from the oil filter housing.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Fits the following BMW engines:
M52, S52, M54

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Cylinder Head Gasket Asbestos-Free - 1,20Mm
This item fits the following BMW Chassis:
E71,E82,E90,E92,E93,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F32,F33,F34,F36

Fits BMW Engines including:
N55

Not only will this kit stop most E90 oil leaks, it's the perfect addition for ignition coil or spark plug replacement! Oil leaks - and the damage they can cause - seem to be the worst annoyances on these cars. The biggest source of an oil leak is from the valve cover, followed by the oil filter housing, Valvetronic seal, camshaft seals, and the eccentric shaft sensor seal. Once the oil leaks, and if ignored for an extended time, the oil will contaminate vital electrical sensors. This is especially the case with ignition coils and also the eccentric shaft sensor on the Valvetronic shaft at the top of the cylinder head. During any ignition coil and spark plug replacement take a close look inside for any oil pooling at the bottom. We have been seeing valve cover oil leaks as soon as 40,000 miles. We look for oil leaks on every E90 that comes into our shop.

We have put together this package of valve cover gaskets and other related gaskets and seals for you to fully overhaul the N52 valve cover and put a stop to those pesky oil leaks. This package has the replacement parts for N52 engines built up to 10/2006 and includes:
 

• 11127581215 - N52 valve cover gasket set
• 11120409288 - N52 aluminum valve cover bolts (1-time use only, not re-usable)
• 11377516302 - N52 Valvetronic gasket
• 11127528242 - N52 eccentric shaft sensor seal

These are all Genuien BMW parts. Replacement of these gaskets and seals is straight-forward but a long process. BMW dealers typically charge for over eight hours of labor. If you have replaced spark plugs before you should be capable of this repair. In addition, there are several other parts to replace while you're in the vicinity: camshaft sensor o-rings, oil filter housing profile gasket, VAN0S solenoids, and the eccentric shaft sensor. These other parts, except the eccentric shaft sensor (see below), are replaceable without removing the valve cover but are more easily accessed during the valve cover work.

Eccentric Shaft Sensor: This is the position sensor that relays the eccentric shaft's position back to the DME. It's located at the front of the engine and is only accessible with the valve cover off. Over time the seal around the sensor comes loose and oil is allowed to blow out of the cam cover and it eventually finds its way into the sensor (which will eventually fail). Without a functioning sensor your E90 can experience poor running, hesitation, poor performance, jerky shifts, and sluggish response. It's easy to check and see if oil has accumulated inside the sensor: unbolt the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside or even around the sensor itself, plan on replacing this sensor during your next ignition coil, spark plug, and/or valve cover gasket work.

This valve cover kit fits the following BMWs:
2006 E90 BMW 325i 325xi 330i 330xi - Sedan
2006 E91 BMW 325xi - Wagon
2006 E60 BMW 525i 525xi 530i 530xi
2006-10/2006 E85 BMW Z4 3.0i Z4 3.0si

Located on the intake side of the cylinder head, this sensor relays the position of the camshaft to the computer in order to determine proper ignition timing. When this sensor fails the engine will generally log a fault code and may place the vehicle into "limp" mode. When this happens it is advised to stop driving the vehicle and address the issue immediately as premature wear or long term damage to the engine is possible.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

OE BMW reference number: 12147539165
 

We also carry a this sensor with the required o ring Here

This part fits the following BMWs:
1998 - 2004 E39 Touring 525i 528i 
1996 - 2004 E39 Sedan 525i 528i 530i  
1999 - 2006 E46  323i 323ci 325i 325ci 325xi 328i 328ci 328xi 330i 330ci 330xi 

Genuine BMW Bearing Ledge Exhaust
 

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

This item fits the following BMW Chassis:
E82 1M Coupe,E70 X5 X5,E71 X6,E82,E83 X3,E85 Z4,E86 Z4,E89 Z4,E90,E92,E93,F01,F02,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4 X4,F30,F32,F33,F34,F36,F80 M3,F82 M4,F83

Fits BMW Engines including:
N51,N52,N52N,N54,N54T,N55,S55