BMW Engine Parts

If your M50, M52, or M54 engine takes a few seconds to build oil pressure after sitting, there's a good chance that your factory oil filter housing drain back valve has failed. Over time, the factory plastic check valve degrades, allowing oil to drain completely out of the housing and back into the oil pan while sitting. Every cold start essentially becomes a dry start, resulting in a loud ticking noise and causing unnecessary wear on your engine's internals.

Unfortunately, BMW does not offer this check valve as a standalone part, forcing you to purchase a costly, complete oil filter housing assembly just to fix one failed plastic component. Thankfully, our team of BMW enthusiasts took note of this common failure mode and designed a permanent, cost-effective fix.

Our Billet Oil Filter Housing Drain-Back Valve is designed as a direct-fit upgrade for your factory oil filter housing. CNC-machined from high-strength billet aluminum, this upgraded valve restores positive sealing to keep the oil filter housing fully primed. Maintaining this hydraulic prime ensures rapid oil pressure stabilization upon startup, directly mitigating dry-start bearing wear and top-end lifter starvation without requiring the purchase of a complete OEM housing assembly.

If you own an M57-equipped BMW, you already know this twin-turbo diesel powerplant is an absolute torque monster. What you might also know is that all that low-end grunt and high-compression diesel vibration wreaks absolute havoc on your accessory drive system.

From the factory, both the E90 335d and E70 X5 35d utilize a rigid alternator pulley. With each cylinder's fire, the crankshaft experiences a violent micro-acceleration. Because the alternator has a heavy internal rotor spinning at high speeds, it wants to keep spinning at a constant rate. When the engine suddenly slows down (even minutely between firing cycles), the alternator fights the belt. This constant tug-of-war results in extreme stress on your engine's belt-driven components. At best, it’s an annoying, unrefined chirp at idle; at worst, it’s a ticking time bomb for your expensive harmonic balancer.

To solve this issue, many enthusiasts choose to run a clutched alternator pulley (also called an overrunning alternator pulley). A clutched pulley allows the alternator to "freewheel" or coast when the engine slows down, completely isolating its rotational inertia from the belt drive to prevent component wear. While the N52's clutched pulley (12317560483) is a straight bolt-on, the offset is incorrect for the E90 335d's accessory drive. Thankfully, our engineers designed this zinc-coated spacer to provide the precise amount of spacing needed to perfectly align the new pulley with existing belt drive components.

The MINI N14 engine uses a traditional pencil coil design that operates using conservative dwell times and relatively low discharge energy. On stock vehicles, this system is sufficient. However, as cylinder pressures increase via higher boost, upgraded turbos, or ethanol-blended fuels, the strength required to bridge the spark gap increases substantially.

Under these conditions, standard N14 coils reach their electrical limits, resulting in high-RPM spark blowout, misfires, or reduced flame front propagation. To solve this issue, our team engineered the B-Series Coil Conversion Kit, which adapts modern BMW B48/B58 ignition technology to the N14 using proprietary brackets, standoffs, and wiring harness adapters. Our performance B48 ignition coils feature a significantly lower primary resistance and an optimized secondary winding structure, allowing them to store and release up to 2.3x more spark energy than the factory N14 ignition coil.

This clean, coil-on-plug upgrade drops directly into your valve cover without bulky external boxes or messy wiring. Whether you need an ignition service or are building a tuned N14, upgrade to B-Series ignition coils and experience improved spark energy and long-lasting performance.

Keep your S55 running cooler, longer. The factory oil cooler thermostat on the S55 waits until the oil reaches roughly 110°C (230°F) before sending it to the cooler. By then, the cooling system is already playing catch-up, especially on track days, spirited canyon runs, hot summer traffic, or tuned cars making well beyond stock power.

Our S55 Billet Oil Cooler Thermostat design addresses this issue at the source. Our proprietary low-temperature 70°C (158°F) thermostat routes oil through the cooler much earlier, so temperatures stay controlled before they climb instead of being pulled back down after the fact. The result is more consistent oil temperatures, more stable performance lap after lap, and less heat stress on bearings, turbochargers, and other critical components.

Unlike thermostat delete or “always open” bypass solutions, our kit uses a real working thermostat. Your engine still warms up properly on cold starts, which protects internal friction surfaces and keeps the oil at the right temperature for daily driving in any climate. Housing the thermostat is a CNC-machined billet aluminum cover, which is much stronger than the factory piece and looks great under the hood. Our thermostat solution is compatible with both factory and -10 AN oil cooler lines when used in conjunction with an AN Line Adapter (see T#59331100).

If you own an M57-equipped BMW, you already know this twin-turbo diesel powerplant is an absolute torque monster. What you might also know is that all that low-end grunt and high-compression diesel vibration wreaks absolute havoc on your accessory drive system.

From the factory, both the E90 335d and E70 X5 35d utilize a rigid alternator pulley. With each cylinder's fire, the crankshaft experiences a violent micro-acceleration. Because the alternator has a heavy internal rotor spinning at high speeds, it wants to keep spinning at a constant rate. When the engine suddenly slows down (even minutely between firing cycles), the alternator fights the belt. This constant tug-of-war results in extreme stress on your engine's belt-driven components. At best, it’s an annoying, unrefined chirp at idle; at worst, it’s a ticking time bomb for your expensive harmonic balancer.

To solve this issue, many enthusiasts choose to run a clutched alternator pulley (also called an overrunning alternator pulley). A clutched pulley allows the alternator to "freewheel" or coast when the engine slows down, completely isolating its rotational inertia from the belt drive to prevent component wear. While the N52's clutched pulley (12317560483) is a straight bolt-on, the offset is incorrect for the E90 335d's accessory drive. Thankfully, our engineers designed this zinc-coated spacer to provide the precise amount of spacing needed to perfectly align the new pulley with existing belt drive components.

MINI N16 1.6L Oil Filter Housing W/ Cover

For Mini owners in need of a replacement oil filter housing, the MINI N16 1.6L Oil Filter Housing with Cover is an essential part. This housing ensures proper filtration of engine oil, maintaining engine health and performance. Crafted with precision engineering and durable materials, it offers the following benefits:

• Ensures proper filtration of engine oil
• Maintains engine health and performance
• Crafted with precision engineering for reliability
• Includes cover for added protection