Turbos

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

Vargas Turbo has done it again. They've made it even easier for you to get your car back on the road and running right again with your new turbos. They've put together an install kit containing all the components you need to get your new turbos installed properly and efficiently. This means you can get your car back on the road faster and enjoy your new turbos! 

Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.

The turbocharger oil supply line is one of the most common failure points on N14 and N18-equipped R5X MINIs. Responsible for delivering a steady stream of pressurized oil to the turbocharger’s center housing (CHRA), this line keeps the turbo’s bearings properly cooled and lubricated. Unfortunately, its location directly alongside the exhaust manifold and catalytic converter exposes it to extreme heat. Over time, this heat causes the oil inside the line to harden or “coke,” creating a permanent restriction that starves the turbo of vital lubrication.

MINI attempted to address this issue by adding a retrofit heat shield to N14 models, but the problem continues to plague MINI owners. Furthermore, the OEM banjo bolts rely on copper crush washers that become brittle and warp under heat, leading to persistent oil leaks at the back of the engine.

To eliminate these issues, ECS developed a high-performance replacement for the factory turbocharger oil feed line (11657534454). Built from premium stainless steel braided -4 AN hose and engineered to withstand the harsh thermal environment of the N14/N18 engine bay, this upgrade ensures consistent, dependable oil delivery. A PTFE inner lining provides exceptional chemical and temperature resistance, while black zinc–coated fittings and banjo bolts offer improved corrosion protection and long-term sealing. The result is a durable, leak-free solution that outperforms the factory design in every way.

Features:

-4 AN stainless steel braided hose eliminates the OE swivel fittings for superior sealing and consistent oil flow

PTFE inner lining delivers outstanding chemical and temperature resistance

Black-anodized aluminum AN fittings offer improved durability and a refined appearance

Black zinc–coated banjo bolts resist corrosion for a long-lasting repair

Includes four new crush washers to ensure proper sealing during installation

Whether you're fixing an oil leak or performing preventative maintenance, choose the ECS upgraded turbocharger oil feed line for lasting durability and leak-proof performance.