Turner Motorsport BMW Sway Bar End Links

These adjustable rear links are only required when using sway bar / swaybars with a suspension with a very low ride height, where it may be necessary to adjust the length of the end links for proper sway bar clearance from the drive axles or other suspension components. These suspensions are usually found only on race cars but this may also apply to street cars with sport springs/sport coil overs that are lowered a lot. On most street cars lowered 1.5" or less, the stock links will be fine.

These end links feature a Heim joint, which allows enough lateral movement when disconnected to adjust the length of the link without removing the entire link from the car. This is particularly helpful when eliminating or adjusting preload while tuning the suspension. Similar links without this joint, can't be adjusted without totally removing the link from the car.

Built-in grease fittings allow for occasional lube, and a packet of grease is included. These links are sold as a set, and include two end links and hardware for H&R and TMS sway bars (other brands may not need the hardware). 

At their shortest setting they are 2.875" hole to hole and on their longest setting they are 3.5" hole to hole.

*Note: these links will not work with factory or non-adjustable Eibach sway bars.

Our renowned TMS adjustable front sway bar / swaybar links for BMWs are now available in custom lengths, making them easy to order for any aftermarket or custom suspension setups. Simply measure for your ideal link length, and order the links with the best length range (below). Each sway bar link has a 10mm diameter mounting pin/stud, which is the typical factory/stock size for a universal fitment. These are sold by the pair, and each set includes two matching sway bar end links.

These end links offer the quiet operation and long life of "stock" BMW end links, but with the strength and adjustability of rod-end style sway bar links. These sway bar links can be used on a wide variety of BMWs and aftermarket BMW suspensions. When measuring, please consider that the length ranges of our Custom Adjustable end links are measured from the center to center on the end link mounting stud / pin, as shown in our diagram.

Note for E9X M3: the unique mounting on the M3 strut requires a set of our adapter seats (#TSU9912AF9). You can add them with your links from the menu below.
 

TMS Part#Center to Center (mm)Center to Center (inch)

TSU9912A35155.00mm - 170.00mm6.10" - 6.69"

TSU9912A40170.00mm - 185.00mm6.69" - 7.28"

TSU9912A45180.00mm - 195.00mm7.08" - 7.67"

TSU9912A50190.00mm - 205.00mm7.48" - 8.07"

TSU9912A55207.00mm - 222.00mm8.15" - 8.74"

TSU9912AF1220.00mm - 235.00mm8.66" - 9.25"

TSU9912A70240.00mm - 255.00mm9.45" - 10.04"

TSU4612AF3250.00mm - 265.00mm9.84" - 10.43"

TSU9912A80261.00mm - 276.00mm10.28" - 10.87"

TSU5012AF8280.00mm - 295.00mm11.02" - 11.61"

TSU9912A95290.00mm - 305.00mm11.42" - 12.00"

TSU9912110320.00mm - 335.00mm12.59" - 13.19"

TSU9912115330.00mm - 345.00mm12.99" - 13.58"

TSU9912130362.00mm - 377.00mm14.25" - 14.84"

TSU9912135370.00mm - 385.00mm14.57" - 15.16"

TSU9912140381.00mm - 396.00mm15.00" - 15.60"

TSU9912145389.00mm - 404.00mm15.31" - 15.91"

Please select your length below. 

You get the best of both worlds with this pair of Turner Motorsport adjustable sway bar links. We searched far and wide to find the hidden gem of swaybar links. You get the same quiet operation and long life as the stock links plus the strength and adjustability of rod-end style sway bar links.

With the wide range of suspensions and sway bars available today adjustable sway bar links can help you with many problems. Along with the ability to remove preload you can change the length to maximize sway bar geometry. Example: if the sway bar hoop comes too close to the steering rack, oil cooler, or under tray in its suspension travel you can adjust it by simply lengthening or shorting the adjustment rod. In some cases you may need a longer or shorter adjustment rod to achieve optimal geometry. We also offer these same links in other custom lengths (click here) that may not be specific to BMW chassis.

Features:

• Adjustable to neutralize preload on sway bar (balanced handling)
• The ability to set sway bar geometry and clearance
• Low friction ball joints
• High articulation
• Direct replacement for OEM sway bar links
• Watertight boot seal
• Ball joint is made by a world leader in ball joint technology, THK. THK's OEM Customers: BMW, Porsche, Ford, GM, Nissan, Honda, and Toyota

Turner Swaybar Link Specs:
TSU9912AF1: 220.00mm - 235.00mm / 8.66" - 9.25"
TSU4612AF3: 250.00mm - 265.00mm / 9.84" - 10.43"
TSU5012AF8: 280.00mm - 295.00mm / 11.02" - 11.61"
TSU9912A95: 290.00mm - 305.00mm / 11.42" - 12.00"

These adjustable sway bar end links can be used on a variety of BMWs. Please select your car below. Please note these end links do not fit non-M E36, except 325i/is produced before 6/1992.