BMW Control Arm Replacements & Upgrades

Updated design!  Now shipping!

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

100% machined and anodized, 6061-T6 lightweight aluminum arms (and collars).

Stainless hardware and spacers are perfect for the tough Northeast climate!

New!  Easy adjustment with 22mm open ended wrench and 5mm allen key!  It only requires 15 ft. lbs. on the clamp to secure the clamp!

New!  Included lock-out kit, replaces factory eccentric hardware.

Updated 3-piece rod ends features 4130 chromoly steel bodies, heat-treated, alloy steel races, and Teflon liners

Extremely easy installation and adjustment (your alignment shop will LOVE you!)

Looking to upgrade your front suspension to increase the strength and your steering angle for the track? IRP has you covered with their BMW Lock Kit. This kit includes new control arms that are stronger than stock and have monoball ball joints, new tie rod ends that feature steel monoball ball joints as well, new offset control arm bushings, fully adjustable camber plates, roll center/bump steer correction plates, and all new hardware. This enables this kit to be fully plug and play, giving you a much more adjustable front suspension, and increases the total amount of steering angle up to 65 degrees.

This kit is perfect for those looking to build a drift car and ensure their suspension is ready to take on the challenge.

Kit features:

• CNC Laser Cut Components
• Plug & Play - includes all needed hardware
• Increase to 65 Degree (or more) steering angle
• Includes Camber Plates
• Stiffer offset control arm bushings
• Roll Center and Bump Steer Correction Plates
• High strength control arms with steel monoball ball joints
• Increased length steering tie rods with steel monoball ball joints
• DriftAllstar- & EEDC-Tested
• Total weight of all components included: 13.5 kg / 29.8 lbs

Fits the following BMWs:
1999-2006 E46 BMW M3

Ball joints begin to pop and rattle after a long period of wear and tear. An OEM Lemforder ball joint is the perfect replacement to ensure complete reliability eliminate any noises from the suspension.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

The front control arm bushings is the Achilles heel on the E39 models. The original factory bushings are fluid filled and rely on the fluid to absorb vibration and resist deflection. When the fluid is gone the rubber left over cannot match the original bushing's strength. The left over rubber is not stiff enough to resist the movements from the suspension. The result is a lot of vibration and reduced feedback and response from the steering.

Meyle has addressed this issue with bushings that are not fluid-filled. The bushing is made of solid rubber that will last longer than the original bushing and is a bit stiffer than new originals for better response and feel. The lack of play from the solid rubber design will mean sharper steering, restoring much of the car's precision and 'connected' feel.

This control arm comes with the Meyle HD bushings already pressed in. This makes for an easy swap out-swap in install. These arms replace the existing stock upper control arms - otherwise known as a tension strut or strut support arm. It's the arm with the twist.

Meyle is a German brand in business since 1958 and all of their products are TUV approved and meet or exceed ISO standards. All Meyle HD parts come with a 4-year, unlimited mileage warranty.

Features:

• 4 Year Warranty

• All metal ball joints are more reliable and longer lasting than stock

• Bushings are solid rubber rather than fluid filled, providing longevity and handling feel improvements

This item fits the following BMWs:
1997-2003 E39 5 Series BMW 525i 525i Wagon 528i 528i Wagon 530i 530i Wagon
2000-2003 E52 Z8 Convertible BMW Z8 Z8 Alpina

One common weak point in the E36 3-series model range is in the mounting and ball joints of the suspension. The front suspension ball joints in particular are prone to wearing out quite quickly thanks to a soft material in the ball joint itself, leaving you in a potentially dangerous situation. At best, worn ball joints and bushings will give you poor steering feedback and clunking noises. However, loose or worn ball joints will have excessive play which will drastically reduce the effectiveness of the steering and suspension. In extreme cases, the ball joint has been known to pop free of the control arm, resulting in total steering loss.

Meyle has addressed this problem with a higher-grade metal in their HD ball joints, similar to those used on the E36 M3. The metal will not wear or fatigue nearly as fast as the standard ball joints. The lifespan is greatly extended. A side benefit of the stiffer joint is better steering response. The metal will not flex or deflect like plastic, rubber, or any other material. The lack of play will mean sharper steering, restoring much of the car's precision and fun-to-drive character. Meyle is a German brand in business since 1958 and all of their products are TUV approved and meet or exceed ISO standards.

We supply the Meyle HD control arms as a set with new M3 rubber control arm bushings. You can choose bushings with either a centered hole (same as stock original) or with an offset hole (adds caster and camber). The stock rubber bushings (manufactured by Boge) will be perfect for most people but if you're looking for an upgrade, the offset bushings will give the car quicker steering response. The solid rubber mounts last longer and give better feedback than the original web design.

All Meyle HD parts come with a 4-year, unlimited mileage warranty.

Features:

• 4 Year Warranty

• All metal ball joints are more reliable and longer lasting than stock

• Bushings are solid rubber rather than fluid filled, providing longevity and handling feel improvements

Package Options:
Bushings without control arm brackets.
Bushings pre-installed into new control arm brackets

Applications:
1992-1999 E36 318i, 318is, 323i, 323is, 325i, 325is, 328i, 328is, including all sedan, coupe, and convertible models.
1995-1999 E36 318ti Compact and hatchback models
1996-2001 Z3 1.9, 2.3, 2.5, 2.8, 3.0

The front control arm bushings is the Achilles heel on the E39 models. The original factory bushings are fluid filled and rely on the fluid to absorb vibration and resist deflection. When the fluid is gone the rubber left over cannot match the original bushing's strength. The left over rubber is not stiff enough to resist the movements from the suspension. The result is a lot of vibration and reduced feedback and response from the steering.

Meyle has addressed this issue with bushings that are not fluid-filled. The bushing is made of solid rubber that will last longer than the original bushing and is a bit stiffer than new originals for better response and feel. The lack of play from the solid rubber design will mean sharper steering, restoring much of the car's precision and 'connected' feel.

This control arm comes with the Meyle HD bushings already pressed in. This makes for an easy swap out-swap in install. These arms replace the existing stock upper control arms - otherwise known as a tension strut or strut support arm. It's the arm with the twist.

Meyle is a German brand in business since 1958 and all of their products are TUV approved and meet or exceed ISO standards. All Meyle HD parts come with a 4-year, unlimited mileage warranty.

Features:

• 4 Year Warranty

• All metal ball joints are more reliable and longer lasting than stock

• Bushings are solid rubber rather than fluid filled, providing longevity and handling feel improvements

This item fits the following BMWs:
1997-2003 E39 5 Series BMW 525i 525i Wagon 528i 528i Wagon 530i 530i Wagon
2000-2003 E52 Z8 Convertible BMW Z8 Z8 Alpina