BMW Sway Bar Kits

These adjustable rear links are only required when using sway bar / swaybars with a suspension with a very low ride height, where it may be necessary to adjust the length of the end links for proper sway bar clearance from the drive axles or other suspension components. These suspensions are usually found only on race cars but this may also apply to street cars with sport springs/sport coil overs that are lowered a lot. On most street cars lowered 1.5" or less, the stock links will be fine.

These end links feature a Heim joint, which allows enough lateral movement when disconnected to adjust the length of the link without removing the entire link from the car. This is particularly helpful when eliminating or adjusting preload while tuning the suspension. Similar links without this joint, can't be adjusted without totally removing the link from the car.

Built-in grease fittings allow for occasional lube, and a packet of grease is included. These links are sold as a set, and include two end links and hardware for H&R and TMS sway bars (other brands may not need the hardware). 

At their shortest setting they are 2.875" hole to hole and on their longest setting they are 3.5" hole to hole.

*Note: these links will not work with factory or non-adjustable Eibach sway bars.

BMW F8X M2 M3 M4 Front Sway Bar End Link Kit is essential for achieving optimal corner balance and handling in your BMW. This kit allows for precise adjustments to ensure the sway bar remains properly aligned and stress-free at static ride height. Adjustable sway bar end links are crucial for maximizing mechanical grip and stability during cornering, braking, and acceleration. By ensuring even loading and eliminating any “zero load” points, this kit enhances chassis dynamics and delivers superior performance.

• Improved Handling: Ensures the sway bar is completely unloaded and unstressed at static ride height for enhanced chassis dynamics.
• Enhanced Corner Balance: Helps achieve an even distribution of weight across each tire, improving stability and grip.
• Precision Adjustment: Allows for fine-tuning of the sway bar links to maintain proper alignment and prevent uneven loading.
• Durable Protection: Dust boots seal the end links to prevent dust and debris from affecting performance.
• Essential for Performance: Critical for those seeking the best handling and cornering performance from their BMW M car.

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 255mm (10") to 315mm (12.4") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints (M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability NOTE: If you've modified your vehicle's suspension with aftermarket struts or coilovers, the mounting location for the sway bar end link may have moved. To confirm fitment with our adjustable end links, please measure the distance between the sway bar and the mounting location on the strut body with the vehicle at ride height and confirm that it is within the 255 mm - 315mm range of adjustment.

To reduce the understeering affects of a staggered wheel setup you want a balanced set of sway bars. ECS has configured this anti-roll bar set for the non-M E46 with a 27mm adjustable front bar and a 21mm rear bar. The front is adjustable to two positions to fine-tune the handling and reduce understeer. The rear bar is fixed to retain the stock sway bar link. These anti-roll bars include urethane bushings with a reinforced inner liner that eliminates squeaks and doesn't require lubrication. The bars are powder coated for durability and good looks.

These bars fit in the stock locations using the existing brackets and links. Adjustable links are not required but recommended if the car is lowered or if you have coil overs (note: the rear bar is designed to only use the stock link, heavily lowered cars should not use this kit).

The bars are adjustable so any driver can find an ideal setup for the type of driving they are doing. The sway bar becomes stiffer in the hole(s) furthest from the end of the bar. The holes at the very end of the bar are the softest setting. We would generally recommend starting out with the front bar set to the stiffer setting and adjust to your liking from there. 

This item fits the following BMWs: 
1999-2006 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left- and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 175mm (6.89") to 235mm (9.25") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints (M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability NOTE: If you've modified your vehicle's suspension with aftermarket struts or coilovers, the mounting location for the sway bar end link may have moved. To confirm fitment with our adjustable end links, please measure the distance between the sway bar and the mounting location on the strut body with the vehicle at ride height and confirm that it is within the 175 - 235mm range of adjustment.

NOW LOCATED UNDER T#339018

To reduce the understeering affects of a staggered wheel setup you want a balanced set of sway bars. ECS has configured this anti-roll bar set for E82 1-series and E9X 3-series with a 28mm front bar and a 15mm rear bar. This kit is designed to help reduce the amount of body roll when cornering and enhance response when turning. These anti-roll bars include urethane bushings with a reinforced inner liner that eliminates squeaks and doesn't require lubrication. The bars are powder coated for durability and good looks.

These bars fit in the stock locations using the existing brackets and links. Adjustable links are not required but recommended if the car is lowered or if you have coil overs.

This item fits the following BMWs: 
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan
2007-2011 E91 BMW 325i 328i - Touring Wagon
2007-2013 E92 BMW 328i 335i 335is M3 - Coupe
2007-2013 E93 BMW 328i 335i 335is M3 - Convertible

BMW E8X E9X Billet Front Sway Bar Brackets With Polyurethane Bushings - Pair provide a superior upgrade over OEM components, offering enhanced rigidity and performance for your BMW. Designed and engineered by Turner Motorsport, this kit is crafted to deliver precision and durability, improving the effectiveness of your front sway bar and reducing body roll.

• Enhanced Rigidity: The billet aluminum brackets offer a more rigid mounting solution compared to factory steel brackets, leading to better handling.
• Improved Performance: Includes polyurethane bushings with a greaseable channel, providing quieter operation and extended service life.
• Precision Construction: Made from 6061-T6 billet aluminum, CNC-machined for exact fitment, and Type II black anodized for corrosion resistance.
• High-Quality Hardware: Comes with zinc flake coated Class 12.9 alloy steel bolts for added performance and durability.
• Better Handling: Reduces sway bar deflection, resulting in sharper, flatter cornering with reduced body roll.
• Simple Installation: Easy to install with included hardware; simply replace your existing sway bar brackets and bushings.

Enjoy improved handling and a more responsive suspension system with this high-performance upgrade from Turner Motorsport.