BMW Drivetrain Parts

Engineered in-house, our torque plate is designed to provide a robust and uniform clamping surface between the flywheel and crankshaft across a range of BMW engine applications. Compatible with both factory and Turner performance flywheels, it helps prevent surface galling and ensures consistent torque distribution during installation.

Features:

Prevents galling and wear at the crankshaft-to-flywheel interface under high clamping loads
Promotes even load distribution for improved fastener integrity and long-term reliability
Compatible with a variety of BMW flywheel setups, including OEM and aftermarket configurations
Design:

Precision-machined from cold rolled steel for high strength and dimensional accuracy
Heat treated to 32 HRC for increased surface hardness and wear resistance
Clear zinc anodized for enhanced corrosion protection
Laser-etched Turner logo
Ideal for performance builds and drivetrain refreshes, this torque plate is a critical component for maintaining proper flywheel installation and maximizing long-term durability across multiple BMW platforms.

The ULTIMATE shifter upgrade for your BMW! Experience more precise throws, less shift lever travel, and an all-around transformation in your shifting experience.

For dozens of years, enthusiasts have critiqued the imprecise and vague feeling of BMW manual transmissions. Plagued with long throws, fore and aft play in gear, and a generally loose feeling, your OEM BMW shifter leaves much to be desired. While most standard carrier-mount short throw shifter kits will aid in reducing throw length and eliminating side-to-side play in gear, some enthusiasts long for a hardcore, race-inspired shifter that completely removes play and excessive throw length. At Turner Motorsport we share the same desire and set out to offer the ULTIMATE upgrade with this Performance Chassis Mount Short Shifter.

WHY UPGRADE?

Factory BMW shifter assemblies are complex by nature. The main component of this assembly is the shift carrier, a cast aluminum piece positioned inside the transmission tunnel that incorporates bushings at both ends for mounting. Like most factory parts, these bushings are designed to reduce NVH (noise, vibration, and harshness) transmission to the cabin. To the spirited driver, however, these bushings translate to flex and vagueness in the shift lever. Moreover, because this carrier is mounted to both the transmission and the body, the entire shifter assembly will "float" with the driveline, further increasing the vague and imprecise feeling of your shifter.

Our Performance Chassis Mount Short Shifter removes the shift carrier assembly entirely—removing any prospect of flex caused by bushings or driveline movement. By contrast, this chassis mount shifter offers a drastic reduction in shift lever travel, vagueness, and side-to-side play. An elevated base allows for moving the fulcrum point upwards, resulting in a much shorter and more precise throw. Shift times are further reduced by a tall, "rally style" shift lever, used to aid in leverage while also bringing the lever closer to the steering wheel. Our design incorporates a proprietary centering spring design, which is adjustable for increasing or decreasing self-centering force. In short, this design eliminates all the drawbacks of your factory BMW shifter, translating to more control, greater precision, shorter throws, and faster shift times.

FEATURES & BENEFITS

Reduced Throw: Modified shifter geometry and heightened fulcrum point translate to a shorter shift lever throw
Improved Shifter Feel: Eliminating the shift carrier and associated bushings drastically reduces "slop" and side-to-side play in the shift lever
Increased Precision: Mounting the shifter to the chassis allows for little to no variation in gear selection
Universal Fitment: Fits many BMW chassis with the provided base plate and hardware (see "Fits These Cars" for exact fitment information)
DESIGN

6061 aluminum, 4130 steel, and 316 stainless steel construction
A type-II black anodized finish
Adjustable self-centering spring
"Rally Style" shift lever
Spherical bearing pivot with maintenance-free brass insert
Product Development:

Our Chassis Mount Shifters are designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing.

The factory BMW S65 dual-mass flywheel is engineered with comfort in mind, catering to the luxury-oriented expectations of the brand’s driving experience. Its design focuses on dampening drivetrain vibrations, smoothing out gear transitions, and minimizing harshness during operation. However, this refinement costs valuable performance. The dual-mass flywheel adds a substantial 27 lbs of rotational mass to the drivetrain, which significantly hinders throttle response and makes rev-matching feel sluggish and disconnected. Moreover, dual-mass flywheels are notorious for being a weak link in modified or high-performance builds and can prove costly to replace when they inevitably fail.

Our Single-Mass Lightweight Flywheel Conversion addresses all of these shortcomings with a purpose-built, lightweight, single-mass design that prioritizes performance. Weighing in at only 19 lbs., this design significantly reduces rotational mass, allowing your S65 to achieve its true motorsport potential!

Features & Benefits:

Precision machined from 4140 HT heat-treated chromoly steel for exceptional toughness, even wear properties, and increased durability.
Material quality promotes even wear across the entire friction surface, prolonging component lifespan.
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability.
Hardness improves component wear characteristics.
Black oxide coated for corrosion resistance on non-friction surfaces.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
Specifically designed to work with S65 OE-architecture clutches.
Optimized step height maximizes clutch clamp load and offers a prolonged service life.
Performance:

8 lbs. lighter than the factory BMW flywheel!
OEM Dual-Mass: 27 lbs.
Turner Motorsport Single-Mass: 19 lbs.
Faster revs
Improved throttle response and acceleration
Allows for a more engaging driving experience and delivers a feeling of direct connection
Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

BMW E30 325i/iS DSSR (187mm) - Turner Motorsport is the ultimate solution to eliminate shifter slop, providing tighter and crisper shifts for your BMW. Developed in collaboration with Rennline, this Dual Shear Selector Rod (DSSR) is designed to significantly reduce flexibility in the selector rod, ensuring a more precise and responsive shifting experience. Whether you're using the stock shifter or a Turner short shift kit, this DSSR will enhance the accuracy of your gear selections with minimal effort.

Does not include a new selector rod joint.

Benefits:

Enhanced Shift Precision: Reduces play and deflection in the linkage, delivering a more positive feel in the shifter.
High-Quality Construction: Crafted from 303 stainless steel for superior corrosion resistance and long-lasting durability.
Compatible Design: Fits BMW E30 325i/iS models with selector rod part 25111221657 and selector joint part 25117580281.
Improved Performance: Works seamlessly with both stock and Turner Motorsport short shifters.
Complete Kit: Includes necessary hardware for easy installation and optimal performance.

Luk is our recommended brand for OE quality replacement clutches. This clutch is an upgrade for non 335is/550i/650i models - featuring a heavy duty clutch disc and more holding power, while still retaining stock pedal feel.

Includes:

• Clutch friction disc
• Throwout/release bearing
• Clutch fork lever
• Pressure plate
• Pressure plate bolts

Fits the following BMW chassis: 

E92,E93,F10,F12,F13

This is an OEM LuK stock twin mass flywheel for E46 M3 and Z4 M roadster with S54 engine. When your clutch starts to experience engagement chatter because of hot spots and wear, replacing it with this OEM dual mass flywheel will restore your vehicles driveability and have you clutch shifting smoothly again. OEM replacement for BMW part # 21212229900, 21212282345, and 21212229940.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1999-2006 E46 BMW M3
2003-2008 Z4 BMW Z4 M Roadster M Coupe

Ensure precise clutch installation with this specialized alignment tool, designed specifically for N54-equipped BMWs. While most aftermarket clutch kits include a generic alignment tool, many are intended for the N55, which is incompatible with the N54 due to differences in pilot bearing mounting and flywheel design.

This tool is engineered for both 6-bolt (01/2009+) and 8-bolt (-01/2009) N54 flywheels, allowing you to accurately center and align the clutch disc on the flywheel during pressure plate installation. Achieve a hassle-free and precise fit with this essential service tool.

It only takes a gust of wind to have your hood crashing down on your head, or if you have a carbon fiber hood and no longer have the gas struts than this could be what you need.

 This hood prop is adjustable, lightweight, and sturdy making it easy to keep out of the way in the trunk so it's there whenever you need it. 

Checking or changing your MINI Cooper's transmission fluid can be a real challenge. But fear not, the Schwaben MINI Automatic Transmission Plug Socket is here to make your life easier.

Designed specifically for MINI Coopers, this Plug Socket Tool eliminates the struggle of accessing the fill plug. Its compact size allows easy maneuverability in tight spots, making transmission fluid checks and changes a breeze. Unlike standard sockets, our specialized socket fits snugly on the drain plug's outer diameter, ensuring stability during use.

The benefits are crystal clear: save time and effort when inspecting, altering, or adding transmission fluid. With our MINI plug socket, removing and installing the fill plug becomes a piece of cake. Say farewell to frustration and hello to efficiency, all thanks to this innovative socket solution.

This is an OEM LuK Clutch Master Cylinder. If your clutch is failing to engage/disengage, but the rest of the assembly is in working order, the master cylinder may be the problem. This is an OEM replacement for BMW part # 21526773670.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Revamp your BMW's shifting experience with the Turner Motorsport Double Adjustable Short Shift Kit, a solution to the historically long throw shifters. Turner's short shifters offer height and throw adjustability, allowing drivers to discover their ideal driving sweet spot.

Curious about the long shifter? Turner's rally lever extension, available separately, provides a Quick Change option, simplifying the transition between long and short levers. Whether for track, weekend adventures, or daily commuting, Turner's short shifter kit caters to diverse driving needs.

Installing this kit is a breeze compared to competitors, thanks to the custom bearing cup that enables easy installation from inside the car. Enjoy the benefits of adjustable throw, ultra-crisp shifter feel, and an engaging driving experience.

Key Features:

• Adjustable throw from conservative to ultra-short
• Ultra-crisp shifter feel for quicker, precise shifts
• Easy installation with custom bearing cup
• Quick Change option for rally lever extension
• Independently adjustable knob height
• 22mm adjustment range for fine-tuning shifter throw
• CNC machined for durability and corrosion resistance

Upgrade further with the Turner Weighted Shift Knob - a 6-speed coin-designed knob that enhances the shifting experience with added weight, resulting in faster engagement and overall improved shifting.

Turner Weighted Shift Knob Features:

• Anodized billet aluminum core
• Durable Delrin outer construction
• Weighs 340g (11.99oz) for enhanced shift feel
• Anodized billet shift boot collar with Turner logo

For a comprehensive shifter makeover, pair the knob with Turner's short shift kits. The knob, carefully crafted from billet 6061-T6 aluminum, is CNC machined for precision fit and finish, anodized for durability, and designed for seamless compatibility with OE BMW shift knobs.

Upgrade your BMW's shifting experience with the Turner Motorsport Double Adjustable Short Shift Kit. Say goodbye to the long factory throws, as Turner's short shifters offer height and throw adjustability, allowing you to find the perfect setting for a more exciting drive.

Don't fret about the long shifter – Turner's rally lever extension (available separately) provides a Quick Change option, effortlessly switching between long and short levers. Whether you're a track enthusiast, a weekend warrior, or a daily driver, Turner's short shifter kit caters to your needs.

Installation is a breeze compared to competitors, thanks to the custom bearing cup that enables easy installation from inside the car. Enjoy the benefits of ultra-crisp shifter feel, quicker and more precise shifts, and an overall more engaging driving experience.

Key Features:

• Adjustable between conservative short throw and ultra-short throw
• Ultra-crisp shifter feel for quick, precise shifts
• Easy installation with custom bearing cup
• Quick Change option for rally lever extension
• Independently adjustable knob height
• 22mm adjustment range for fine-tuning shifter throw
• CNC machined for durability and corrosion resistance

Upgrade your shifting experience further with the Turner Weighted Shift Knob. Crafted from billet 6061-T6 aluminum, this knob offers a solid, precise feel, enhancing overall shifting performance. With a weight of 340g, it's up to 179% heavier than stock knobs, ensuring smoother shifts and a better driving feel.

Turner Weighted Shift Knob Features:

• Anodized billet aluminum core
• Durable Delrin outer construction
• 340g weight for enhanced shift feel
• 6 Speed Coin design
• Anodized billet shift boot collar with Turner logo

Pair these upgrades with the Turner Motorsport DSSR for E36 328 and M3 models. Designed in collaboration with Rennline, this Dual Shear Selector Rod reduces flexibility in the selector rod, resulting in more precise shifts. Machined from 303 stainless steel, it eliminates shifter slop for a positive feel.

Turner DSSR Features & Benefits:

• Reduces play in the shifter for a more positive feel
• Manufactured from 303 stainless steel for corrosion resistance
• Compatible with stock or Turner shifters
• Necessary hardware included for easy installation

Upgrade your BMW's shifting performance with Turner Motorsport – where precision meets driving pleasure.

OEM LuK Clutch Kit includes Clutch Disc, Pressure Plate, and T/O Bearing. Call for applications not listed above. SACHS is the OEM supplier for BMW. 

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!