BMW Engine Parts

Turner Motorsport Billet Aluminum Oil Filter Housing Drain-Back Valve...

T#:56110301

Part#: 060233LA01

In Stock

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

If your M50, M52, or M54 engine takes a few seconds to build oil pressure after sitting, there's a good chance that your factory oil filter housing drain back valve has failed. Over time, the factory plastic check valve degrades, allowing oil to drain completely out of the housing and back into the oil pan while sitting. Every cold start essentially becomes a dry start, resulting in a loud ticking noise and causing unnecessary wear on your engine's internals.

Unfortunately, BMW does not offer this check valve as a standalone part, forcing you to purchase a costly, complete oil filter housing assembly just to fix one failed plastic component. Thankfully, our team of BMW enthusiasts took note of this common failure mode and designed a permanent, cost-effective fix.

Our Billet Oil Filter Housing Drain-Back Valve is designed as a direct-fit upgrade for your factory oil filter housing. CNC-machined from high-strength billet aluminum, this upgraded valve restores positive sealing to keep the oil filter housing fully primed. Maintaining this hydraulic prime ensures rapid oil pressure stabilization upon startup, directly mitigating dry-start bearing wear and top-end lifter starvation without requiring the purchase of a complete OEM housing assembly.

Show More Show Less

Turner Motorsport - VANOS Exhaust Hub Upgrade - E46 M3, Z3 M, Z4 M (S...

T#:53538140

Part#: 013042LA01

In Stock

$ 262.99

This product was last offered at the strikethrough price on
05-06-2026

$ 179.99 USD

Add to Wish List

Qty

$ 179.99 USD

Add to Wish List

The factory VANOS exhaust hub on the S54 engine is known to develop excessive play where the drive tabs interface with the oil pump disk. Over time, this imprecise fitment causes a back-and-forth rattling motion that can result in the tabs shearing off inside the engine, risking catastrophic damage or complete engine failure. Unlike other aftermarket solutions that require full VANOS disassembly, retiming, or replacement of the oil pump disk, the Turner Motorsport S54 VANOS Hub Upgrade offers a smarter approach. Our bolt-on fix eliminates the common failure point without opening the VANOS unit or disturbing engine timing.

Our solution involves removing the worn tabs from your stock exhaust hub and installing our precision-fit replacement, which is precision-machined from 4340 steel and hardened to meet OEM specifications. Designed using 3D scanning and CAD modeling, the Turner Motorsport VANOS Exhaust Hub Upgrade provides a tight, interference-free fit into the oil pump disc, completely resolving the issue without unnecessary labor.

Features & Benefits:

Direct bolt-on solution for S54 VANOS oil pump drive tab failure, preventing potentially catastrophic damage to engine internals Precision-machined from high-strength 4340 steel and heat-treated to match OEM specifications Designed using 3D scanning and CAD modeling to ensure precise fitment within the OEM oil pump disc Engineered to eliminate the play that exists between the exhaust hub and oil pump disc from factory Backed by extensive real-world testing and our lifetime replacement program!

Show More Show Less

Turner Motorsport Polished Valve Cover Cap Nut (11121738607) - Priced...

T#:54852009

Part#: 059043LA04KT

Ships on Sep 9, 2026

$ 4.99 USD

Add to Wish List

Qty

$ 4.99 USD

Add to Wish List

Over time, the factory valve cover hardware on M50, M50TU, M52, M52TU, M54, S50 (US), and S52 engines is subjected to continuous heat cycling, oil vapor, and moisture, causing original cap nuts to oxidize, corrode, or thread-strip during routine maintenance. Our Polished Valve Cover Cap Nut serves as a direct replacement designed to address these common failure points while improving upon overall engine bay aesthetics.

Because maintaining precise gasket compression is critical to preventing oil leaks, these cap nuts and washers are machined directly to OE-style dimensions. This exact fitment allows for direct compatibility with original and replacement valve cover studs (see T#55317643) and ensures the hardware can be torqued precisely to OEM specifications without guesswork. Manufactured to grade 8.8 structural strength standards, the hardware maintains the necessary clamp force required under normal and high-performance engine operating conditions.

To resist corrosion, both the cap nut and washer undergo an electroless nickel plating process during production. Unlike standard zinc coatings that dull or rust over time, electroless nickel provides a uniform layer of corrosion resistance that withstands long-term chemical exposure and extreme temperature swings while giving the hardware a polished, high-end appearance. Each cap nut assembly includes an OE rubber washer seal, ensuring a tight, leak-free barrier that prevents oil from escaping through the mounting studs.

Show More Show Less

Turner Motorsport Clutched Alternator Pulley Conversion Kit - E90 335...

T#:55497480

Part#: 060119LA01KT

In Stock

$ 73.99 USD

Add to Wish List

Qty

$ 73.99 USD

Add to Wish List

If you own an M57-equipped BMW, you already know this twin-turbo diesel powerplant is an absolute torque monster. What you might also know is that all that low-end grunt and high-compression diesel vibration wreaks absolute havoc on your accessory drive system.

From the factory, both the E90 335d and E70 X5 35d utilize a rigid alternator pulley. With each cylinder's fire, the crankshaft experiences a violent micro-acceleration. Because the alternator has a heavy internal rotor spinning at high speeds, it wants to keep spinning at a constant rate. When the engine suddenly slows down (even minutely between firing cycles), the alternator fights the belt. This constant tug-of-war results in extreme stress on your engine's belt-driven components. At best, it’s an annoying, unrefined chirp at idle; at worst, it’s a ticking time bomb for your expensive harmonic balancer.

To solve this issue, many enthusiasts choose to run a clutched alternator pulley (also called an overrunning alternator pulley). A clutched pulley allows the alternator to "freewheel" or coast when the engine slows down, completely isolating its rotational inertia from the belt drive to prevent component wear. While the N52's clutched pulley (12317560483) is a straight bolt-on, the offset is incorrect for the E90 335d's accessory drive. Thankfully, our engineers designed this zinc-coated spacer to provide the precise amount of spacing needed to perfectly align the new pulley with existing belt drive components.

Show More Show Less

Turner Motorsport M57 Clutched Alternator Pulley Conversion Kit - E70...

T#:55497484

Part#: 060119LA02KT

In Stock

$ 73.99 USD

Add to Wish List

Qty

$ 73.99 USD

Add to Wish List

The Turner Motorsport M57 Clutched Alternator Pulley Conversion Kit for BMW E70 X5 35d M57 engines converts rigid factory pulleys to an overrunning clutched setup. Rigid stock pulleys transmit crankshaft micro-accelerations, driving belt chatter and harmonic balancer failure. Combining an OE N52 clutched pulley with a zinc-coated alloy steel spacer isolates rotational inertia to protect accessory drive components.

Show More Show Less

Turner Motorsport Valve Cover Stud (11121718856) - Priced Each ...

T#:55317643

Part#: 059043LA03

Ships on Sep 9, 2026

$ 4.99 USD

Add to Wish List

Qty

$ 4.99 USD

Add to Wish List

This M7/6x29.5 threaded stud is used for securing the valve cover to the cylinder head on all M50, M50TU, M52, M52TU, M54, S50 (US), and S52 engines. Despite this crucial role in engine sealing and construction, BMW decided to discontinue this vital factory part in 2023. Recognizing the gap left by the discontinued factory hardware, our team of BMW enthusiasts reverse-engineered the original part—improving its materials and finish to bring a higher-quality, long-lasting solution to the market. Manufactured from high-strength Grade 8.8 steel and finished with a protective zinc coating, this upgraded stud delivers exceptional durability, reliable torque retention, and exceptional corrosion resistance under the hood.

Show More Show Less

Turner Motorsport B-Series Ignition Coil Conversion Kit - MINI N14 R5...

T#:56507850

Part#: 060205LA01KT

In Stock

$ 398.60 USD

Add to Wish List

Qty

$ 398.60 USD

Add to Wish List

The MINI N14 engine uses a traditional pencil coil design that operates using conservative dwell times and relatively low discharge energy. On stock vehicles, this system is sufficient. However, as cylinder pressures increase via higher boost, upgraded turbos, or ethanol-blended fuels, the strength required to bridge the spark gap increases substantially.

Under these conditions, standard N14 coils reach their electrical limits, resulting in high-RPM spark blowout, misfires, or reduced flame front propagation. To solve this issue, our team engineered the B-Series Coil Conversion Kit, which adapts modern BMW B48/B58 ignition technology to the N14 using proprietary brackets, standoffs, and wiring harness adapters. Our performance B48 ignition coils feature a significantly lower primary resistance and an optimized secondary winding structure, allowing them to store and release up to 2.3x more spark energy than the factory N14 ignition coil.

This clean, coil-on-plug upgrade drops directly into your valve cover without bulky external boxes or messy wiring. Whether you need an ignition service or are building a tuned N14, upgrade to B-Series ignition coils and experience improved spark energy and long-lasting performance.

Show More Show Less

Turner Motorsport Clutched Alternator Pulley Conversion Spacer - E70 ...

T#:55497479

Part#: 060119LA02

In Stock

$ 9.99 USD

Add to Wish List

Qty

$ 9.99 USD

Add to Wish List

If you own an M57-equipped BMW, you already know this twin-turbo diesel powerplant is an absolute torque monster. What you might also know is that all that low-end grunt and high-compression diesel vibration wreaks absolute havoc on your accessory drive system.

From the factory, both the E90 335d and E70 X5 35d utilize a rigid alternator pulley. With each cylinder's fire, the crankshaft experiences a violent micro-acceleration. Because the alternator has a heavy internal rotor spinning at high speeds, it wants to keep spinning at a constant rate. When the engine suddenly slows down (even minutely between firing cycles), the alternator fights the belt. This constant tug-of-war results in extreme stress on your engine's belt-driven components. At best, it’s an annoying, unrefined chirp at idle; at worst, it’s a ticking time bomb for your expensive harmonic balancer.

To solve this issue, many enthusiasts choose to run a clutched alternator pulley (also called an overrunning alternator pulley). A clutched pulley allows the alternator to "freewheel" or coast when the engine slows down, completely isolating its rotational inertia from the belt drive to prevent component wear. While the N52's clutched pulley (12317560483) is a straight bolt-on, the offset is incorrect for the E70 X5 35d's accessory drive. Thankfully, our engineers designed this zinc-coated spacer to provide the precise amount of spacing needed to perfectly align the new pulley with existing belt drive components.

Show More Show Less

Turner Motorsport Clutched Alternator Pulley Conversion Spacer - E90 ...

T#:55497466

Part#: 060119LA01

In Stock

$ 9.99 USD

Add to Wish List

Qty

$ 9.99 USD

Add to Wish List

If you own an M57-equipped BMW, you already know this twin-turbo diesel powerplant is an absolute torque monster. What you might also know is that all that low-end grunt and high-compression diesel vibration wreaks absolute havoc on your accessory drive system.

From the factory, both the E90 335d and E70 X5 35d utilize a rigid alternator pulley. With each cylinder's fire, the crankshaft experiences a violent micro-acceleration. Because the alternator has a heavy internal rotor spinning at high speeds, it wants to keep spinning at a constant rate. When the engine suddenly slows down (even minutely between firing cycles), the alternator fights the belt. This constant tug-of-war results in extreme stress on your engine's belt-driven components. At best, it’s an annoying, unrefined chirp at idle; at worst, it’s a ticking time bomb for your expensive harmonic balancer.

To solve this issue, many enthusiasts choose to run a clutched alternator pulley (also called an overrunning alternator pulley). A clutched pulley allows the alternator to "freewheel" or coast when the engine slows down, completely isolating its rotational inertia from the belt drive to prevent component wear. While the N52's clutched pulley (12317560483) is a straight bolt-on, the offset is incorrect for the E90 335d's accessory drive. Thankfully, our engineers designed this zinc-coated spacer to provide the precise amount of spacing needed to perfectly align the new pulley with existing belt drive components.

Show More Show Less

VTT B58/S58 Cylinder Head Port Block-Off Kit - BMW B58 Gen1/2/3 (B58/...

T#:49822557

Part#: VTTBS58BLOCK

In Stock

$ 29.99 USD

Add to Wish List

Qty

$ 29.99 USD

Add to Wish List

The VTT B58/S58 Head Port Block-Off kit is designed to either seal off the factory head ports used by the OEM low-side PCV system. These ports in the cylinder head utilize engine vacuum to evacuate crankcase gases, but in the process, can allow oil to enter the intake manifold, leading to valve carbon buildup and other performance issues over time. The Block-Off kit offered by VTT completely seals the factory head ports to prevent oil intrusion and unwanted vacuum leaks. This kit does NOT require any tapping, meaning no metal to get into the engine, etc. You simply tap the plugs into place. Key Features Eliminates oil draw-through into the intake manifold Prevents carbon buildup on intake valves Utilizes precision-machined plugs for boost sealing Fully reversible — Block-offs can be removed if needed No tapping is required. Easy install, by tapping the blocks into place.

Show More Show Less

Vargas Burnt Titanium Magnetic Oil Drain Plug - M12 X 1.5

T#:51813315

Part#: VTT-TI-DRAIN

Ships in 5 Business Days

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

The VTT Burnt Titanium Magnetic Oil Drain Plug is a critical upgrade for any performance enthusiast looking to maximize engine longevity.

Blue Thermostat Caps (pair)

T#:54139632

Part#: BMS-TCP-BLU

Ships in 2 Business Days

$ 29.00 USD

Add to Wish List

Qty

$ 29.00 USD

Add to Wish List

Blue B58 BMW Coil Upgrade Adapter Kit - N55

T#:49857415

Part#: BMSN55CUAK

Back Ordered

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Upgrade your N55 ignition system with the N55 → B58 Coil Upgrade Adapter Kit, engineered for a seamless, plug-and-play conversion. This kit lets you run modern B58-style pencil coils on your N55 without modifying the factory harness or compromising valve cover integrity. Why Upgrade: While the N55 is a reliable platform, factory coils can struggle under high boost, heat, and load. B58 coils deliver stronger, more consistent spark, and this adapter kit ensures a clean, OEM-quality integration. Features & Benefits: Direct-fit adapter harness & mounts for straightforward B58 coil installation Plug-and-play design — no cutting, splicing, or permanent modifications Secure coil seating & alignment for consistent performance and reliability Improved ignition stability under high-load or tuned conditions, helping reduce misfires Applications: Stage 1–3 N55 builds, turbo upgrades, ethanol blends, track use, and aggressive daily driving Drivers looking to eliminate heat- and boost-related ignition issues Anyone seeking an OEM+ quality coil upgrade without a messy DIY install Result: A clean, professional installation that modernizes your ignition system and delivers reliable spark performance under all conditions. If you provide the kit’s brand/part number and whether your valve cover is stock or aftermarket, I can refine this description for precise fitment and application.

Show More Show Less

BMS Oil Catch Can Oil Filler Cap Dual Vent Connection Kit - G2X/G42/A...

T#:49822554

Part#: BMSB58OCCFCDV

Ships on Aug 31, 2026

$ 139.00 USD

Add to Wish List

Qty

$ 139.00 USD

Add to Wish List

Keep crankcase vapors in check and your intake air clean with the BMS Oil Catch Can Oil Filler Cap Dual Vent Connection Kit for the Gen2 B58. This upgrade ditches the flimsy factory venting in favor of a precision CNC-machined billet oil filler cap and dual-vent fittings engineered to handle increased crankcase pressure under boost. By diverting oil-laden vapors into a catch can instead of back through the intake, this system helps minimize carbon buildup, reduces oily contamination, and promotes more consistent performance as power levels climb. High-quality hoses and fittings ensure a secure, leak-free install that won’t collapse under pressure and maintains a clean, OE-plus appearance in the engine bay. An easy, effective upgrade for B58 enthusiasts looking for cleaner operation, improved engine longevity, and proven performance-focused design

Show More Show Less

VTT Turbocharger Inlet Flange - Garrett G40/42/45 V-Band - 86mm ID ...

T#:52270240

Part#: GARROUTT4G4045

Ships on Aug 28, 2026

$ 37.99 USD

Add to Wish List

Qty

$ 37.99 USD

Add to Wish List

Upgrade your turbocharger exhaust connection with the VTT-FAB 86mm V-Band Outlet Flange, designed for the Garrett G40-G45 frame sizes.

Vargas Titanium Valve Cover Hardware Upgrade - Black - BMW B58, N55, ...

T#:52129732

Part#: VTT-TI-BOLTS-2-B

Back Ordered

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

The VTT Titanium Valve Cover Hardware Kit is the ultimate finishing touch for your BMW N55, S55, or B58 engine.

JB4PRO Flex Fuel Add On Harness - B58/S58

T#:49822568

Part#: JB4PB58FFAOH

In Stock

$ 49.00 USD

Add to Wish List

Qty

$ 49.00 USD

Add to Wish List

Take your B58 or S58 build further with the JB4PRO Flex Fuel Add-On Harness—a simple, plug-and-play way to add an ethanol sensor and optional fuel pressure sensor to your JB4PRO setup. Keep your install clean, your wiring organized, and your tune dialed to match every fuel blend in the tank. Why it matters: Plug & Play: Connects directly to your JB4PRO—no cutting or splicing required. Sensor Ready: Supports ethanol and fuel pressure sensors for precise, real-time fueling adjustments. Clean, Safe Installation: Includes a 12 V adapter and inline fuse for hassle-free integration. How it works: This harness links your JB4PRO tuner to your flex fuel hardware. It’s not a complete flex fuel kit—you still need a compatible ethanol sensor—but it gives your JB4PRO the accurate readings it needs to adjust timing, boost, and fueling for E30, E50, or E85 blends.

Show More Show Less

Vargas Plug And Play S58 Single HPFP Conversion Kit - BMW G8X/F9X S58...

T#:51778123

Part#: VTT-S58-SINGLE-H

In Stock

$ 349.00

This product was last offered at the strikethrough price on
07-28-2026

$ 316.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 349.00

This product was last offered at the strikethrough price on
07-28-2026

$ 316.99 USD

Limited Qty Sale

Add to Wish List

The Vargas Turbo Technologies (VTT) S58 Single HPFP Conversion Kit is a revolutionary solution for high-horsepower BMW G8X and F9X builds.

Vargas Oil Feed Adapter - BMW N54

T#:51778141

Part#: VTT-N54-OFA

In Stock

$ 41.99

This product was last offered at the strikethrough price on
08-03-2026

$ 39.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 41.99

This product was last offered at the strikethrough price on
08-03-2026

$ 39.99 USD

Limited Qty Sale

Add to Wish List

The Vargas Oil Feed Adapter is designed to replace the stock front turbo oil feed line with a robust, CNC-machined solution.

Turbo & Intake Heat Shield - Gen2 B58

T#:49857413

Part#: BMSG2B58THS

Ships on Aug 31, 2026

$ 119.00 USD

Add to Wish List

Qty

$ 119.00 USD

Add to Wish List

Keep heat where it belongs and boost where it counts with a B58 Turbo & Intake Heat Shield for BMW and Toyota Supra—an OE-plus style upgrade that helps your setup stay cooler, more consistent, and happier when you’re leaning on it. BMW’s factory heat management is fine at stock-ish levels, but once you start turning the wick up, the turbo becomes a rolling space heater. That radiant heat soaks the nearby intake tract, nudging IATs up and making performance less repeatable pull after pull. This shield steps in as a dedicated barrier between the turbo and intake components, helping reduce heat soak so you can keep intake air cooler and denser when you’re driving it like you mean it. Built with a clean, factory-inspired mindset, it’s precision-formed to wrap neatly around the B58 turbo and intake area, and it mounts using factory locations for a tidy, OEM-level install. No cutting, no permanent changes, and fully reversible—just a straightforward bolt-on that looks right at home in the engine bay. Made from durable, heat-resistant materials, it’s designed to handle the heat long-term without turning into a crispy science project. Why it matters Cuts down radiant heat from the turbocharger into the intake area Helps reduce intake air temperature creep Improves consistency during repeated pulls and hard driving Adds protection for surrounding components exposed to turbo heat Features & highlights Designed for BMW B58 and Toyota Supra applications Precision-formed for OEM-level fitment Heat-resistant construction for long-term durability Bolt-on install using factory mounting points Clean, OE-plus under-hood appearance

Show More Show Less

Turbo & Intake Heat Shield - Gen1 B58

T#:49857410

Part#: BMSB58THS

Ships on Aug 31, 2026

$ 119.00 USD

Add to Wish List

Qty

$ 119.00 USD

Add to Wish List

Keep heat where it belongs and boost where it counts with a B58 Turbo & Intake Heat Shield for BMW and Toyota Supra—an OE-plus style upgrade that helps your setup stay cooler, more consistent, and happier when you’re leaning on it. BMW’s factory heat management is fine at stock-ish levels, but once you start turning the wick up, the turbo becomes a rolling space heater. That radiant heat soaks the nearby intake tract, nudging IATs up and making performance less repeatable pull after pull. This shield steps in as a dedicated barrier between the turbo and intake components, helping reduce heat soak so you can keep intake air cooler and denser when you’re driving it like you mean it. Built with a clean, factory-inspired mindset, it’s precision-formed to wrap neatly around the B58 turbo and intake area, and it mounts using factory locations for a tidy, OEM-level install. No cutting, no permanent changes, and fully reversible—just a straightforward bolt-on that looks right at home in the engine bay. Made from durable, heat-resistant materials, it’s designed to handle the heat long-term without turning into a crispy science project. Why it matters Cuts down radiant heat from the turbocharger into the intake area Helps reduce intake air temperature creep Improves consistency during repeated pulls and hard driving Adds protection for surrounding components exposed to turbo heat Features & highlights Designed for BMW B58 and Toyota Supra applications Precision-formed for OEM-level fitment Heat-resistant construction for long-term durability Bolt-on install using factory mounting points Clean, OE-plus under-hood appearance

Show More Show Less

Blue B58 BMW Coil Upgrade Adapter Kit - N54

T#:49857414

Part#: BMSN54CUAK

Ships on Aug 31, 2026

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Modernize your N54 ignition system with this N54 to B58 Coil Upgrade Adapter Kit, engineered to deliver an OEM-quality conversion for improved spark energy and consistency. Designed to pair B58-style pencil coils with the factory N54 engine harness, this kit provides a clean, reversible installation—no cutting, splicing, or guesswork required. Key Features & Benefits: Direct-fit adapter solution to run B58 coils on N54 applications Plug-and-play wiring integrates with the factory N54 harness for a factory-like install Secure coil positioning helps ensure proper seating and reliable long-term fitment Improved ignition stability under higher cylinder pressures—ideal for tuned, higher-boost setups Clean, serviceable conversion that maintains a tidy engine bay and simplifies future maintenance Ideal For: Stock to heavily modified N54 builds Vehicles running elevated boost, ethanol blends, or upgraded turbo systems Owners looking to reduce ignition-related misfires and improve combustion consistency under load If you share the brand/part number of the kit and which coils you’re pairing it with, I can tailor the write-up to match the exact components and fitment notes.

Show More Show Less

SNEED4SPEED MINI Cooper W11 Performance Engine - Super Sport 53SSCE ...

T#:54388498

Part#: 2028215

Ships in 2 Business Days

$ 8,295.00 USD

Add to Wish List

Qty

$ 8,295.00 USD

Add to Wish List

Rebuilt performance engines that are great for the street to track level

Vargas Billet Cylinder Head Outlet Adapter - Blue - BMW N54/N55 ...

T#:51918881

Part#: VTT-COOLADBLUE

Ships on Aug 28, 2026

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

The Vargas Billet Cylinder Head Outlet Adapter is the definitive solution for one of the most common failure points in BMW N54 and N55 engines.

Vargas Billet Extended Turbo Drain Adapter - T3/T4 Square, Garrett GT...

T#:52129710

Part#: VTT-FAB-081

Ships on Aug 28, 2026

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

Upgrade your custom turbo setup with the Vargas Turbo Technologies VTT-FAB-081 Billet Extended Drain Adapter.

VTT Turbocharger Inlet Flange - 2" Sch 10 - Garrett G25/G30/G35 ...

T#:52270239

Part#: GARING25

Ships on Aug 28, 2026

$ 27.99 USD

Add to Wish List

Qty

$ 27.99 USD

Add to Wish List

Unlock the full potential of your Garrett G-Series turbocharger with the VTT-FAB Precision Inlet Flange.

VTT GC-Lite 2.0 Stock Location Turbocharger - Black - BMW N54 RHD ...

T#:52270267

Part#: GCLRHDBLK

Ships on Aug 28, 2026

$ 2,619.99 USD

Add to Wish List

Qty

$ 2,619.99 USD

Add to Wish List

For the N54 enthusiast who demands race-car power without sacrificing the daily-driver feel, the VTT GC-Lite 2.0 is the definitive choice.

Vargas Billet Adapter With Straight Gate For EWG DCS - BMW

T#:52094551

Part#: VTT-DCS-EWG-ONLY

Ships on Aug 28, 2026

$ 839.99 USD

Add to Wish List

Qty

$ 839.99 USD

Add to Wish List

The Universal DCS System is the ultimate boost control solution for any vehicle, regardless of whether it came with factory electronic wastegate control.

Vargas GC-Mid Turbocharger Upgrade - BMW B58 TU 2-port

T#:52305479

Part#: B58-GCMID-2

Ships on Aug 28, 2026

$ 2,409.99 USD

Add to Wish List

Qty

$ 2,409.99 USD

Add to Wish List

Engineered specifically for the B58TU 2-port platform, the VTT GC-Mid (Game Changer - Mid) focuses on volumetric efficiency and thermal management.

Vargas Billet Valve Cover & Catch Can Kit - Gold - BMW N54 Engine ...

T#:52129721

Part#: VTTVCOCCCOMBG

Ships on Aug 28, 2026

$ 1,859.99 USD

Add to Wish List

Qty

$ 1,859.99 USD

Add to Wish List

Upgrade your engine’s reliability and ventilation with the VTT "All You Need" Kit, featuring the only gold valve cover currently on the market for the N54.

Vargas Modular Catch Can Kit - Single Can, Stock PCV - BMW E9X, E8X N...

T#:52270289

Part#: OCC2SCSP

Ships on Aug 28, 2026

$ 311.99 USD

Add to Wish List

Qty

$ 311.99 USD

Add to Wish List

This VTT Modular Catch Can kit is the ultimate solution for N54 owners looking to improve their engine’s health without overcomplicating their setup.

VTT F-RB+ Turbocharger - BMW N54 335i LHD

T#:52270283

Part#: N54-FRBPLUS

Ships on Aug 28, 2026

$ 3,479.99 USD

Add to Wish List

Qty

$ 3,479.99 USD

Add to Wish List

The Vargas N54 F-RB+ kit is a ground-up re-engineering of the iconic "GC" line, focusing on thermal efficiency and structural longevity.

Vargas Billet Extended Turbo Drain Adapter - T3/T4 -10 AN - BMW B58, ...

T#:52094591

Part#: VTT-FAB-062

Ships on Aug 28, 2026

$ 53.99 USD

Add to Wish List

Qty

$ 53.99 USD

Add to Wish List

If you are fabricating a custom single-turbo kit or upgrading your current setup, the VTT-FAB-062 is an essential component for a clean and reliable oiling system.

Vargas DCS EWG System Billet Adapter With BMW Actuator - BMW ...

T#:52094552

Part#: VTT-DCS-EWG-W-AC

Ships on Aug 28, 2026

$ 1,049.99 USD

Add to Wish List

Qty

$ 1,049.99 USD

Add to Wish List

the VTT DCS Billet Adapter with BMW Actuator is the definitive solution for converting to an electronic external wastegate.

Vargas Remote Oil Filter Plate & Fittings - -10AN - BMW S58

T#:52164924

Part#: S58OFILPLATE

Ships on Aug 28, 2026

$ 149.00 USD

Add to Wish List

Qty

$ 149.00 USD

Add to Wish List

For dedicated drag racing applications where every ounce of weight and simplicity matters, the VTT S58 Remote Oil Plate is the ultimate "delete" solution.

Black Forest Industries Engine Mounts - Stage 1 - BMW E30 / E36 / E46...

T#:50934264

Part#: BFI-BMW-90-01

Ships on Sep 4, 2026

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

Eliminate the "drive-line slop" common in the E36 and E46 chassis with this Stage 1 Engine Mount kit.

Vargas Billet Cylinder Head Outlet Adapter - Black - BMW N54/N55 ...

T#:51918879

Part#: VTT-COOLADBLK

Ships on Aug 28, 2026

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

The Vargas Billet Cylinder Head Outlet Adapter is the definitive solution for one of the most common failure points on the BMW N54 and N55 engines.

BFI Transmission Mounts - Stage 1 - BMW E30 / E36 / E46 / E9X / Z3 / ...

T#:50934269

Part#: BFI-BMW-TRANS-01

Ships on Sep 4, 2026

$ 69.99 USD

Add to Wish List

Qty

$ 69.99 USD

Add to Wish List

This kit is a "must-have" for any E36, E46, or E9X owner looking to tighten up their drivetrain's foundation and ensure long-term mechanical reliability.

Vargas Billet Extended Turbo Drain Adapter - -10AN Male - Garrett GT,...

T#:52094592

Part#: VTT-FAB-063

Ships on Aug 28, 2026

$ 53.99 USD

Add to Wish List

Qty

$ 53.99 USD

Add to Wish List

Simplify your single-turbo conversion or custom build with the VTT-FAB-063 Billet Extended Drain Adapter.

Vargas Coil Hold Down Kit - Gold - BMW N54

T#:51918876

Part#: VTT-N54CBGOLD

Ships on Aug 28, 2026

$ 112.99 USD

Add to Wish List

Qty

$ 112.99 USD

Add to Wish List

Upgrade your N54 engine bay with the VTT Stock Style Coil Hold Down Kit in Billet Gold.

Vargas Charge Pipe Weld MAP Sensor Bung Flange - BMW B48, B58, S58 ...

T#:52094555

Part#: VTT-FAB-015

Ships on Aug 28, 2026

$ 21.99 USD

Add to Wish List

Qty

$ 21.99 USD

Add to Wish List

The VTT-FAB Billet MAP Sensor Bung is the definitive choice for tuners and fabricators seeking a reliable mounting solution for B48, B58, and S58 platforms.

Vargas Single Catch Can Bracket - BMW N54

T#:51778144

Part#: VTT-N54-SCCB

Ships on Aug 28, 2026

$ 27.99 USD

Add to Wish List

Qty

$ 27.99 USD

Add to Wish List

Designed with flexibility in mind, the VTT N54 Specific Single Catch Can Bracket allows the end-user to take complete control of their PCV routing.

Vargas Billet Motor Mount Inserts - BMW F2X/F3X N55 & B58

T#:51918869

Part#: VTT-INSERT-6

Ships on Aug 28, 2026

$ 474.99 USD

Add to Wish List

Qty

$ 474.99 USD

Add to Wish List

The Vargas Billet Motor Mount Insert Kit is for BMW owners who want to eliminate the factory engine movement without the vibrations of a solid mount.

PFS Port Injection Kit - BMW G8X/F9X S58

T#:52164908

Part#: PFS-S58-PI-NONE

Ships on Aug 28, 2026

$ 949.99 USD

Add to Wish List

Qty

$ 949.99 USD

Add to Wish List

The PFS S58 Port Injection Kit by Vargas Turbo Technologies is the solution for BMW owners who have reached the limits of their factory injection.

Vargas Billet Oil Drain Adapter - -10AN Male - BMW B58

T#:52094563

Part#: VTT-FAB-040-AN

Ships on Aug 28, 2026

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

The VTT-FAB-040 is a high-performance billet aluminum adapter flange specifically engineered for the BMW B58 engine platform.

Vargas High Flow Catch Can System - BMW G8X M2, M3, M4

T#:51918850

Part#: VTT-HFCCG8X16

Ships on Aug 28, 2026

$ 649.00 USD

Add to Wish List

Qty

$ 649.00 USD

Add to Wish List

The Vargas G8X High-Flow -16 Catch Can System is a ground-up solution specifically engineered for high-horsepower BMW G80 M3, G82/G83 M4, and G87 M2 builds.

Vargas High Flow Catch Can System - BMW G8X M2, M3, M4

T#:51918851

Part#: VTT-HFCCG8X12

Ships on Aug 28, 2026

$ 599.00 USD

Add to Wish List

Qty

$ 599.00 USD

Add to Wish List

The VTT High-Flow Catch Can System is engineered specifically for high-horsepower BMW G8X builds where standard PCV systems fail to keep up.

Vargas Stage 3 VTT VTX-R60 - Black - BMW N54 "Limited Fitment" ...

T#:52305462

Part#: S32VTXR60BK

Ships on Aug 28, 2026

$ 10,859.99 USD

Add to Wish List

Qty

$ 10,859.99 USD

Add to Wish List

Transform your BMW into a true street or track monster with the VTT N54 Stage 3 VTX-R Twin Turbo Kit.

Vargas Billet Solid Engine Mounts - BMW G8X M2/M3/M4

T#:51672722

Part#: VTT-G8X-SOLID-MO

Ships on Aug 28, 2026

$ 524.99 USD

Add to Wish List

Qty

$ 524.99 USD

Add to Wish List

The VTT Billet Solid Engine Mounts are the ultimate solution for G8X owners looking to extract every ounce of performance from their S58-powered machines.

Vargas Billet Oil Cooler Adapter Fittings - BMW G80 M3, G82 M4, G83 M...

T#:51778119

Part#: VTT-G8X-OILCOOLE

Ships on Aug 28, 2026

$ 109.00 USD

Add to Wish List

Qty

$ 109.00 USD

Add to Wish List

The VTT G8X Billet Oil Cooler Adapter Fittings are the essential building blocks for any custom S58 oiling project.

Project Cars

SELECT YOUR BMW

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results