BMW Engine Parts

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

Fits the following BMWs:
2000-2006 E46 BMW 323/325/328/330

This genuine BMW replacement oil drain plug with washer is perfect to replace your old beat up or stripped oil plug for easy removal and oil changes.

Genuine BMW Screw Plug
This item fits the following BMW Chassis:
E70 X5M,E71 X6M,E53 48IS,E38,E39,E53 X5 X5,E63,E65,E70 X5,E71 X6,F01,F02,F06,F10,F12,F13,F15,F16

BMW offers their M Performance retrofit kit for your 340i/i xDrive & 440i/i xDrive for increased power and a more aggressive sounding and free flowing exhaust! This system directly from BMW is perfect for those looking for more power and an aggressive exhaust note without voiding the warranty! Upon installation, an immediate improvement is noticed, especially in the low to mid range powerband. The kit increases your vehicle’s power by 35 hp to 355hp and 39 lb-ft of torque to 369 lb-ft (355 lb-ft for manual transmission vehicles).The BMW M Performance Power kit now comes bundled with a higher flowing, valve controlled exhaust for maximum performance and exhilaration! The BMW M Performance Power Kit features engine tuning software and an electronically controlled valve exhaust system that is actuated in Sport/Sport+ modes via the driving experience control button. 

Included with the Power and Sound Kit:

• M Performance Muffler
• M Performance Decal Kit
• Stick on label and Badge
• Performance BMW software upgrade code
• Wiring Harness

After ordering this kit, simply take this to your dealer to have the ECU re-flashed and all of the components included installed! 

The muffler included must also be used with the following BMW exhaust tips:

• Carbon Fiber - Priced Each
• Chrome - Priced Each

*Dealer pricing for installation varies from dealer to dealer. Please contact your dealer for installation cost before purchasing.
 

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4

For the US E36 M3. Schrick 264/256 degree camshafts boost mid-high end power for that extra motivation at higher rpm. Low-end torque is not seriously affected due to the M50/M52s VAN0S System. And, higher profile cams work extremely well with an upgraded intake and exhaust. When upgrading the cams there are other areas you must take into consideration. Higher-flow fuel injectors, larger mass-air sensor, and custom programming are strongly recommended. Turner Motorsport sells complete intake & cam packages that boost power to over 290hp. See the Engine section under Camshafts for more info.

Cam Specs:
Intake - 264 degree, 11.2mm lift
Exhaust - 256 degree, 10.6mm lift

Schrick Technical Information / Specs

This item fits the following BMWs:
1993-1998 E36 BMW 325i 325is 325ic 328i 328is 328ic M3
1993-1995 E34 BMW 525i
1997-1998 Z3 BMW Z3 2.8
1998-1999 Z3 BMW M Roadster M Coupe

Still looking for more power after bolt-ons? High performance camshafts from Schrick are the way to go. These cams are a direct replacement for the stock cams and give a solid 15+ horsepower boost at the top end and great midrange torque increases too! More gains can be expected with intake and header upgrades and custom software tuning. A slightly lumpy idle is expected at cold start but will be smooth once at operating temperature. This set is just a great all-around cam upgrade for the S54!

These Schrick cams were initially developed for the M3 CSL but they also work great on the US and other non-CSL S54 engines as well. With more duration they are a great match to high flow headers, no cats, or CSL intake manifold upgrades. These are the new "cast" cams from Schrick which require new rocker arms (Schrick recommended or BMW part #11337833259). Professional installation is a must due to the intricacies with the double VAN0S.

Schrick Technical Information / Specs

This item fits the following BMWs:

• 2001-2006 E46 BMW M3
• 2001-2002 Z3 BMW M Roadster M Coupe
• 2006-2008 E85 BMW Z4 M Roadster M Coupe

SEE T#338745 BMW S54 3.2L Schrick Camshaft Set 280/272 12.5mm Lift is the perfect performance upgrade for enthusiasts seeking to enhance their engine's capabilities. With over 40 years of experience, Schrick is dedicated to producing high-quality camshafts that deliver exceptional power and reliability. Designed for both street and track applications, these camshafts offer an impressive balance of performance and drivability. The intake cam features a duration of 280, while the exhaust cam has a duration of 272, with a valve lift of 12.5mm. These new "cast" cams from Schrick closely resemble the stock E46 M3 CSL cams, ensuring a smooth idle and a significant increase in horsepower throughout the RPM range. With a peak gain of 15 horsepower and no loss in low-end torque, these camshafts are a top choice for BMW enthusiasts.

Key Benefits:

• Enhanced Power: Delivers a peak gain of 15 horsepower.
• Smooth Idle: Maintains a factory-like idle quality for everyday driving.
• Linear Power Increase: Provides a steady increase in horsepower from midrange to redline.
• Compatibility: Designed to fit the BMW S54 engine with new rocker arms required.
• High-Quality Construction: Crafted from top materials for strength and durability.