Drivetrain Mounts and Upgrades

Stock mounts are made from soft rubber and are sometimes filled with fluid to give a car the most comfortable ride possible. The soft rubber and fluid helps to reduce the total amount of vibration, noise, and harshness (NVH) that is transferred into the cabin. The problem with this is driveline slop. The stock mounts allow a lot of excess movement and increases the amount of time it takes to transfer power to the wheels.

In order to address this issue, performance mounts can be substituted to reduce the amount of slop and transfer power to the wheel quicker. Two options for this are polyurethane mounts and solid mounts.

Solid mounts are great for an immediate transfer of power but allow for a ton of noise and vibration to be felt and heard in the cabin of the vehicle. This is great for the track where there aren't any issues with excess harshness, but as a daily driver, this can become an annoying pain in the neck.

The best middle ground is Polyurethane. Polyurethane is much stiffer than rubber and gives you the much stiffer feel you may be looking for. This allows for the increase in responsiveness, but isn't so extreme that it transfers all of the sound and vibrations into the cabin. This makes it much more comfortable for daily use while still reinforcing your driveline.

Features:

• Aluminum and Polyurethane Construction
• 80A Durometer Rating
• New Hardware

Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.

By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components. 

Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved acceleration response, more direct shifting feel and overall improved drivetrain composure with Powerflex performance polyurethane bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.

By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components. 

Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved acceleration response, more direct shifting feel and overall improved drivetrain composure with Powerflex performance polyurethane bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.

By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components. 

Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved acceleration response, more direct shifting feel and overall improved drivetrain composure with Powerflex performance polyurethane bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.  *Door Buster Special - New Product*

Upgrade your Mini with the PFF5-220 Lower Torque Mount Bracket & Bushing, designed to replace the softer OE mount prone to cracking and excessive engine movement. Ideal for standard or mildly tuned cars, this mount bracket is 300% stiffer than the worn OE mount, offering improved handling and gear shifting precision for fast road use. With CNC machined aluminum construction and various durometer bushing options, it reduces engine movement while enhancing on/off throttle balance. Easy to install with just two bolts, it eliminates the need for pressing out rubber. Expect a slight increase in NVH, particularly at idle.

Benefits:

• 300% stiffer than OE mount
• Reduces engine movement and wheel hop
• Improves handling and gear shifting precision
• Easy installation with two bolts
• Compatible with standard or mildly tuned cars

Stock mounts are made from soft rubber and are sometimes filled with fluid to give a car the most comfortable ride possible. The soft rubber and fluid helps to reduce the total amount of vibration, noise, and harshness (NVH) that is transferred into the cabin. The problem with this is driveline slop. The stock mounts allow a lot of excess movement and increases the amount of time it takes to transfer power to the wheels.

In order to address this issue, performance mounts can be substituted to reduce the amount of slop and transfer power to the wheel quicker. Two options for this are polyurethane mounts and solid mounts. 

The middle ground is Polyurethane. Polyurethane is much stiffer than rubber, but these still let a large amount of movement in comparison to solid mounts. These are great for sporty, aggressive street driving, but for the track are not ideal.

For the track, solid mounts are great. Solid mounts give you an immediate transfer of power, at the cost of increase NVH. This is great for the track where comfort is the least of your worries and power is all that is important.

Features:

• Aluminum and Polyurethane Construction
• 80A Durometer Rating
• New Hardware

MINI F54 to F57 Race Polyurethane Engine Support Bushing - Large is designed to improve engine stability and performance by reducing engine movement. Unlike OEM rubber bushings that prioritize comfort, these Powerflex polyurethane bushings are firmer and more durable, ensuring optimal engine retention and reduced engine slop.

Powerflex, Europe's top-selling suspension bushing manufacturer, utilizes state-of-the-art techniques to produce these exact-fit, premium performance bushings. Built to last longer than OEM rubber bushings, they enhance performance and provide a more engaging driving experience.

• Reduces engine movement for improved stability
• Firmer and more durable than OEM rubber bushings
• Ensures optimal engine retention
• Enhances performance and driving experience
• Exact-fit manufacturing for easy installation
• Recommended use of Powerflex Copper Grease PCG1 for installation
• Suitable for both track and street-driven vehicles
• Backed by Powerflex Lifetime Warranty