BMW Tools & Specialty Equipment for BMW G42 M240i xDrive B58 3.0L

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible ½-inch drive click-to-stop
• Torque range of 10 to 150 ft-lb
• Accurate to within +/-4%
• 18 inches in length with a convenient carry case

The perfect kit containing most of your needed European essentials. 

Features:

• 13PCS-1/4" DR.6PT SOCKETS: 4, 4.5 , 5 ,5.5 ,6 , 7, 8 ,9 ,10, 11, 12, 13, 14MM 
• 1PC- 1/4" DR. QUICK RELEASE RATCHET (72T).
• 2PC- 1/4" DR.50 & 100MM EXTENSIONS 
• 1PC- 1/4" DR.150MM FLEXIBLE EXTENSION
• 1PC- 1/4" DR.UNIVERSAL JOINT
• 1PC- 1/4" DR.SLIDING T-BAR
• 1PC- 1/4" DR.6" SPINNER HANDLE
• 1PC- 1/4" DR.1/4" BIT HOLDER ADAPTER
• 4PCS-HEX KEY WRENCHES:1.27, 1.5,2,2.5MM
• 6PCS-1/4" HEX SOCKETS:3,4,5,6,7,8MM
• 3PCS-1/4' SLOTTED SOCKETS:4,5.5,7MM
• 3PCS-1/4" PHILIPS SOCKETS:PH1, PH2, PH3
• 3PCS-1/4"POZI SOCKETS: PZ1, PZ2, PZ3
• 6PCS-1/4" TORX SOCKETS: T10, T15, T20, T25, T30, T40

Own an E30? This tool kit is a perfect fit for your glovebox!

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible 3/8"-inch drive click-to-stop
• Torque range of 5 to 80 ft-lb
• Accurate to within +/-4%

Tired of busting your knuckles from old hardened exhaust hangers?

This Schwaben tool removes the hanger by pressing on the steel hanger bracket and pulling the rubber hanger in one motion. Self centering force pin locks onto the pin while the flat paddle pulls off the rubber hanger from behind. Slim profile and a 25 degree offset works in tight areas.

If you're removing trim panels and don't want to scratch or break any pieces then this is a must have. Formed for precision and constructed from plastic to be gentle with the finish.

Features:

•  Wide type remover
• Pull type remover
•  Handy remover
• Narrow type remover
• Upholstery Clip remover
• Angled Clip Panel Remover
• Fork Tip Flat Clip Panel Remover
• Clip Panel Remover
• Sharp Tip Flat Clip Remover
• Panel Remover
• Blunt Tip Flat Clip Panel Remover

Custom exhaust work in the plans? The Schwaben Exhaust Pipe Cutter will help you cut out old pipe or cut down new pipe with ease. It can cut any pipes from 3/4" to 3" in diameter and cuts pipe with only 1/4 turn adjustments, thanks to 15 blades that effectively cut the entire pipe with little movement. This is great for tight to reach places that prevents you from using more traditional non-specialty tools.

Features:

• Cuts from 3/4" pipe up to 3" pipe
• 15 cutting blades
• Rubber covered handles for grip and comfort

Schwaben 8-Pc ATF Adapter Set is designed to provide a versatile solution for working with automatic transmission fluid (ATF) systems. This comprehensive adapter set includes multiple sizes to ensure compatibility with a wide range of vehicles, making it an essential tool for automotive professionals and DIY enthusiasts alike.

• Versatile Compatibility: Includes multiple adapters to fit various vehicle makes and models, making it a valuable addition to any automotive toolkit.
• High-Quality Construction: Made from durable materials to withstand the rigors of professional use and provide reliable performance.
• Enhanced Precision: Ensures accurate fluid transfer and servicing by providing the correct adapter size for different ATF systems.
• Convenient Set: Contains all necessary adapters for a comprehensive solution, eliminating the need for separate purchases.
• Easy to Use: Designed for straightforward application, allowing for efficient and effective ATF service and maintenance.

A professional quality flex ratchet features a fine satin finish designed for durability and easy clean up.

Features:

• Special designed 72T gear mechanism
• 5 degree of handle movement between gears 
• Flex head has 7 detent positions in a 180 degree swing
• Push button release holds socket tight until you are ready to release
• Ratchet is a full 290mm ( 11") long for extra leverage.

Limited Lifetime Warranty

All the right bits in one box. The perfect assortment to keep the job going.

Features:

• 10 fractional SAE hex, 9 Torx® tamper-proof, 9 Torx®

• 9 Metric hex bits, 9 slotted bits, 8 Pozi-drive, 8 Phillips, 4 square-recess, 4 tri-wing

• 3 spline, 3 Torq, 3 clutch, wing-nut driver, magnetic bit holder and socket bit holder

• Made of hardened Chrome Vanadium steel for years of dependable use

• Packaged in a handy blow molded case with individually marked bit slots for easy organization

This hand held Schwaben tool makes changing fluids an easy, quick task.The Schwaben fluid suction/fill pump suitable for oils, water and any non corrosive liquid.

Features 

• Comes with a flexible and a rigid tube. 
• Flow rate is adjustable for different functions.
• 350 ML capacity
• Cylinder is marked in 20 mL increments and fraction of quarts for accurate filling. 

Not for use with gasoline.

Wall Hangers Set is the ideal solution for organizing and storing QuickJack frames in a garage. Designed for those who prefer a clean and efficient storage solution, these hangers provide a convenient way to keep your portable car lift frames off the ground and out of the way. The hangers mount directly into a sturdy wall stud, ensuring safe and simple storage for all QuickJack models. Each mount is crafted with a sleek, laser-cut QuickJack logo, affirming its authenticity and quality.

• Secure storage: Mounts directly into wall studs for safe and stable hanging of QuickJack frames.
• Universal fit: Accommodates all QuickJack models, ensuring versatility and convenience.
• Durable construction: Over-engineered to 150% of the rated capacity for long-lasting durability.
• High-quality materials: Made from brushed steel for a robust and stylish appearance.
• Authentic design: Features a sleek, laser-cut QuickJack logo, reflecting its official status and rigorous engineering standards.
• Easy installation: Simple to install, with real-world testing and advanced computer analysis ensuring reliability and resilience.

Upgrade your garage organization with the Wall Hangers Set for a neat, secure, and professional storage solution for your QuickJack frames.

The Schwaben Metric Bubble Flaring Tool Set stands as the ultimate solution for achieving precise brake line connections and flawless tubing applications. This tool set unlocks the ability to craft immaculate ISO bubble flares on brake lines and tubing systems commonly found in European, Japanese, and select domestic model brake lines. The outcome? Connections that are not only secure but also capable of thriving under your vehicle's demanding conditions.

At its core, this set features a robust and enduring hardened steel bar, embodying the essence of durability. Complementing this bar is an extensive array of adapters tailored for 4.75mm, 6mm, 8mm, and 10mm tubing, showcasing the set's versatility across various applications.

Discover unparalleled precision as you secure your brake lines and tubing with the utmost accuracy. This tool set empowers you to effortlessly shape bubble flares, guaranteeing connections that are both leak-proof and resilient. Whether you're a devoted automotive technician or a passionate enthusiast, the Schwaben Metric Bubble Flaring Tool Set is right for you!

Includes:

• Schwaben Metric Bubble Flaring Tool
• Hardened Steel Bar for Enduring Durability
• Adapters for 4.75mm, 6mm, 8mm, and 10mm Tubing

This complete set of extra deep sockets work great on cars equipped with extended studs. They also work as a long wheel nut socket for those deeply recessed nuts in wheels.

Features:

• 17mm, 19mm and 21mm socket in a sturdy blow molded case
• All sockets are 1/2" drive and a full 5-15/16 ( 150MM ) long
• Sockets are designed with inner bore to accept a 5" long stud