The main reason all of the VANOS units will eventually fail is because the material used for the sealing rings from the factory is not designed for that type of environment. When this happens the only option that BMW leaves you with is buying a new and expensive VANOS unit with the same sealing rings that failed in your original unit.

The VANOS system found in BMW engines is a great feature (when it’s working properly), keeping your power curve smooth and responsive especially in lower to mid RPM range. What usually goes unnoticed is the gradual loss of power within this range as the vehicle's age due to slowly failing seals within the VANOS unit. The way the VANOS system works is based off of oil pressure triggered by a solenoid that allows for a small range of timing degree adjustment, this is where the power curve is affected. When the seals begin to fail (all of them do) there is less pressure to advance the timing reducing the power in that low to mid range. Because this happens slowly it's very hard to notice a difference until you refresh your VANOS unit, then you easily realize the response you've been missing.

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

While you're replacing the seals in your VANOS unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy VANOS clatter.

Seals & O-rings:

The seals  were the main focus of this project since the OE units are built with Buna-N rubber o-rings instead of the ECS supplied Viton rubber o-rings. The Buna-N material quickly hardens from the heat and chemical exposure within the engine, where the Viton is significantly more resistant to these chemicals. This knowledge was also used when it came to the commonly failed o-rings found on the VANOS seal plate, replaced at the solenoid.

Rattle Repair:

When it comes to the VANOS rattle this is commonly described as "marbles in a can", and can be heard throughout the different RPM ranges depending on the engine. These upgraded rings and washers are precision ground from hardened steel to resist wear and deformation keeping your VANOS rattle free. The rattle repair tools are designed specifically for this VANOS anti-rattle repair, design from hardened steel to stand up to the job. Designed to perfectly follow the splines of the shaft for a tight grip when applying the necessary torque to disassemble & reassemble the VANOS transfer gear. The keyed socket was designed with the intent to use a "common" wrench so this can be completed at home in your garage.    

When Servicing your VANOS unit we recommend getting everything you need to replace on the way to service which includes an oil change and valve cover gasket set. Fresh oil and gaskets is the best way to start off a fresh rebuild of any kind giving you the maximum performance of your freshly serviced components.

Don't forget to check out our rebuild PDF to make sure you have everything to get the job done and eliminate the rebuild guess work.

This item fits the following BMWs: 
2000-2001 E46 3 Series M3 M3 Convertible 2000-2006 
2001-2002 Z3 Roadster / Coupe Z3 M Roadster Z3 M Coupe w S54 Engine 
2006-2008 E86 E86 Z4 Z4 M Roadster Z4 M Coupe

From years of European automotive experience, the enthusiasts at ECS Tuning have developed a strong understanding of what it takes to produce a quality high-performance brake pad. After thousands of miles and many different pad compounds, they've landed on the ideal blend for the new EP24 "Enthusiast Performance" brake pad! If you're looking for a streetable, track-capable, performance brake pad, look no further than the ECS EP24!

Features & Benefits:

Strong stopping power - Increased coefficient of friction offers satisfying stopping power when cold (a necessity for a street pad!) and even more G-force-inducing power when they warm up. With cold and warm friction comparable to Hawk HPS (and higher than many other street pads) the stopping experience with the EP24 pad is impressive for street-driven vehicles on streetable tires. Positive initial bite - Race pads have the reputation of acting like an on/off switch, which is a no-go for a pad for a street application. The EP24 offers OE-level initial bite for low-stress braking in stop-and-go situations. Reasonable dust - Race pads utilize a high metallic composition. Pads that use high amounts of metal not only dust terribly, but also will bake onto wheels with high temperatures and are a bear to clean. This is not the case with these performance street pads. Now using these pads on most of our shop cars, we’ve found over time that dust is comparable to factory pads in most applications (with greatly improved braking performance). Quiet braking - It’s not a race pad, so it shouldn’t squeal like one. While not as quiet as our ceramic DD23 pad, you’ll still be able to drive your spouse to dinner. Long life - This should be an obvious one. Even in a performance pad, your daily driver pads should last and last, so that was key in selecting our ideal compound. This compound wears slower and is kinder to rotors than two of the top competitors.

EP24 "Enthusiast Performance" brake pads are included in our Lifetime Replacement Program for worry-free motoring.

Silicone Coupler - Straight 3" ID (76.20mm) x 3" L

No matter the project, ECS Tuning silicone couplers and elbows offer a high-quality, precision-engineered solution to your needs. Whether you're installing an intercooler, fabricating a custom intake system, or whatever else you can dream up, ECS Tuning has you covered.

• High-quality silicone construction for durability
• Precision-engineered design ensures a perfect fit
• Versatile solution for various automotive projects
• Enhances performance and reliability
• Compatible with BMW and other vehicles

Drastically improve the looks of your vehicle while improving your vehicle's handling characteristics and/or easily adjust your wheel fitment to allow for the proper clearance when installing parts such as new wheels, big brake kits, or lowering suspension components.Interference from components such as shocks, springs, or control arms are a common issue when installing wheel that are not a direct OE size replacement. By moving your wheels a few millimeters each, you can give yourself enough clearance for proper wheel fitment and give your car a wider stance in the process.

ECS Tuning wheel spacers are constructed of high quality 6061-T6 aircraft grade aluminum and are specifically designed by in-house engineers and cnc machined to exact standards, ensuring the best fitment possible. By carefully measuring the OEM wheel hubs and bore dimensions, these spacers mount with minimal clearance to prevent any vibration, retaining the stock-like vibration free operation. 

ECS Tuning is a performance and genuine parts provider that designs their ECS Tuning branded aftermarket automotive parts in-house to ensure the highest quality and affordability possible. Every part's design is subjected to a rigorous test fit and stress test period to guarantee proper fitment and continued reliability for years to come.

This item fits the following BMWs:

2008-2012 E82 BMW 128i 135 1M
1988-1991 E30 BMW M3
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2012 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2012 E93 BMW 328i 335i M3 - Convertible
1976-1981 E12 BMW 528i 530i
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 530i 535i 540i M5
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i M5
1982-1989 E24 BMW 633csi 635csi M6
2004-2010 E63 BMW 645ci 650i M6
1981-1987 E23 BMW 733i 735i
1988-1994 E32 BMW 735i 735il 740i 740il 750il
1995-2001 E38 BMW 740i 740il 750il
1990-1999 E31 BMW 840i 840ci 850i 850ci 850csi
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
2009-2016 Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

Rear Only
2007-2013 E70 BMW X5M
2007-2014 E71 BMW X6 xDrive35i X6 xDrive50i X6M

From years of European automotive experience, the enthusiasts at ECS Tuning have developed a strong understanding of what it takes to produce a quality high-performance brake pad. After thousands of miles and many different pad compounds, they've landed on the ideal blend for the new EP24 "Enthusiast Performance" brake pad! If you're looking for a streetable, track-capable, performance brake pad, look no further than the ECS EP24!

Features & Benefits:

Strong stopping power - Increased coefficient of friction offers satisfying stopping power when cold (a necessity for a street pad!) and even more G-force-inducing power when they warm up. With cold and warm friction comparable to Hawk HPS (and higher than many other street pads) the stopping experience with the EP24 pad is impressive for street-driven vehicles on streetable tires. Positive initial bite - Race pads have the reputation of acting like an on/off switch, which is a no-go for a pad for a street application. The EP24 offers OE-level initial bite for low-stress braking in stop-and-go situations. Reasonable dust - Race pads utilize a high metallic composition. Pads that use high amounts of metal not only dust terribly, but also will bake onto wheels with high temperatures and are a bear to clean. This is not the case with these performance street pads. Now using these pads on most of our shop cars, we’ve found over time that dust is comparable to factory pads in most applications (with greatly improved braking performance). Quiet braking - It’s not a race pad, so it shouldn’t squeal like one. While not as quiet as our ceramic DD23 pad, you’ll still be able to drive your spouse to dinner. Long life - This should be an obvious one. Even in a performance pad, your daily driver pads should last and last, so that was key in selecting our ideal compound. This compound wears slower and is kinder to rotors than two of the top competitors.

EP24 "Enthusiast Performance" brake pads are included in our Lifetime Replacement Program for worry-free motoring.

Ensure a tight and leak-free seal in your BMW's cooling, vacuum, or intake systems by installing a new adjustable hose clamp. Over time, clamps can deform or lose their tightness due to aging or frequent removal, potentially causing leaks in your coolant or vacuum hoses. Avoid the risk of leaks by replacing old clamps with new hardware, offering peace of mind against coolant and vacuum system issues.

Key benefits of the adjustable hose clamp include:

• Maintaining a secure and leak-free seal in your BMW's systems.
• Preventing coolant or vacuum leaks that can affect performance.
• Adjustable size from 70mm to 78mm for versatile applications.

Upgrade your hose clamps to ensure optimal performance and reliability in your BMW's systems.

Shifter slop is a common complaint among all BMW models. Some of that play comes from the bushings where the shifter carrier mounts to the transmission. The original rubber carrier bushings don't last very long and when they get too soft the shifter flops around. These Delrin bushings have almost no deflection and will last much longer than the factory rubber, giving you precise shifting for many years.

Note: this is only one part of the shift linkage and there may be other components that need replacing to improve shifting feel.

New carrier bushing pins are included.

Revamp your BMW's exhaust aesthetics with the ECS Tuning "Ti.22" Titanium Exhaust Tips, known for their remarkable attractiveness in the market. These exhaust tips showcase a stunning matte titanium finish and a slant-cut, single-wall outlet design, elevating your vehicle's appearance. Engineered for durability, they feature chrome-plated nuts, a 304SS cap screw, and clamp.

Key Benefits:

• Eye-catching matte titanium finish for enhanced aesthetics
• Slant-cut, single-wall outlet for a stylish look
• Durable construction with chrome-plated nuts and 304SS cap screw
• Universal fitment for various vehicles but may require modification for proper installation

Note: Modification might be necessary for proper fitment. This part offers UNIVERSAL fitment and may not directly fit your vehicle. Measuring before ordering is necessary.

Elevate your BMW project with ECS Tuning silicone couplers and elbows, providing a high-quality, precision-engineered solution for various applications. Whether you're installing an intercooler, fabricating a custom intake system, or pursuing other automotive projects, ECS Tuning delivers reliable performance and durability. Trust ECS Tuning to meet your needs and enhance your BMW project.

• High-quality silicone couplers and elbows for BMW projects
• Precision-engineered for reliability and performance
• Versatile solution for intercooler installations, custom intake systems, and more
• Ensures durability and longevity for your automotive projects

Drastically improve the looks of your vehicle while improving your vehicle's handling characteristics and/or easily adjust your wheel fitment to allow for the proper clearance when installing parts such as new wheels, big brake kits, or lowering suspension components.Interference from components such as shocks, springs, or control arms are a common issue when installing wheel that are not a direct OE size replacement. By moving your wheels a few millimeters each, you can give yourself enough clearance for proper wheel fitment and give your car a wider stance in the process.

ECS Tuning wheel spacers are constructed of high quality 6061-T6 aircraft grade aluminum and are specifically designed by in-house engineers and cnc machined to exact standards, ensuring the best fitment possible. By carefully measuring the OEM wheel hubs and bore dimensions, these spacers mount with minimal clearance to prevent any vibration, retaining the stock-like vibration free operation. 

ECS Tuning is a performance and genuine parts provider that designs their ECS Tuning branded aftermarket automotive parts in-house to ensure the highest quality and affordability possible. Every part's design is subjected to a rigorous test fit and stress test period to guarantee proper fitment and continued reliability for years to come.

This item fits the following BMWs:

2008-2012 E82 BMW 128i 135 1M
1988-1991 E30 BMW M3
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2012 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2012 E93 BMW 328i 335i M3 - Convertible
1976-1981 E12 BMW 528i 530i
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 530i 535i 540i M5
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i M5
1982-1989 E24 BMW 633csi 635csi M6
2004-2010 E63 BMW 645ci 650i M6
1981-1987 E23 BMW 733i 735i
1988-1994 E32 BMW 735i 735il 740i 740il 750il
1995-2001 E38 BMW 740i 740il 750il
1990-1999 E31 BMW 840i 840ci 850i 850ci 850csi
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
2009-2016 Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

Rear Only
2007-2013 E70 BMW X5M
2007-2014 E71 BMW X6 xDrive35i X6 xDrive50i X6M

Elevate your BMW's security with the BMW Conical Seat Locking Wheel Bolt Kit. This comprehensive kit provides peace of mind by securing your wheels against theft. Engineered specifically for BMW vehicles, these locking wheel bolts offer a precise fit and reliable performance. Say goodbye to worries about wheel theft and enjoy enhanced protection for your BMW with this essential locking bolt kit.

• Enhances security for BMW wheels
• Precision engineered for a perfect fit
• Provides peace of mind against wheel theft
• Specifically designed for BMW vehicles

Carbon Fiber UNIVERSAL Swivel Exhaust Tips - 4.0" - Pair are designed to provide a stunning, adjustable upgrade for any vehicle. These high-quality exhaust tips feature a unique swivel collar design, allowing them to be adjusted in any direction for the perfect fitment. Simply position the tip to your desired angle and secure it with a hex bolt tightened to 14 ft-lbs (19 Nm), ensuring it stays in place.

• Customizable Fitment: The swivel collar design allows for versatile adjustment, ensuring a perfect alignment with your vehicle's exhaust system.
• Premium Materials: Constructed with single wall stainless steel and a rolled carbon fiber edge for a high-end look and durability.
• Durable Construction: Includes chrome-plated nuts, 304SS cap screw, clamp, and insert ring for long-lasting performance.
• Sleek Appearance: Features a slant cut and matte clear coated ECS Tuning vinyl logo for a stylish finish.
• Universal Fitment: Designed to fit various vehicles; modification may be required for proper fitment.

Dimensions:

• Inlet Size: 2.5"
• Overall Length: 6.0" (5.0" Tip + 1.0" Clamping Surface)
• Outlet Size: 4.0"
• Outlet Style: Single Wall Stainless, Rolled Carbon Edge, Slant Cut
• Sold as a Pair: Includes 2 tips.

If you're looking to fabricate your custom exhaust project and need quality, price-friendly options, then we have you covered with our ECS Tuning Universal Exhaust catalog! These select items feature the same premium benefits as our In-House Engineered Exhaust Systems so you can be confident in their quality and longevity!

PART DESIGN

• Made from T304 Stainless Steel for corrosion resistance and features an attractive brushed finish
• 2.50" outside diameter (OD)
• 1.5mm (.060") wall thickness tubing for durability
• Overall Length (OAL) is approximately 24.00"

PRODUCT DEVELOPMENT

Throughout our development process of our In-House Engineered Exhaust Systems, we have developed top-tier exhaust components, direct-fit to specific European applications. We want to offer the same great quality items to our customers who want to fabricate their own custom-exhaust project, so now you can make it your own!

INSTALLATION AND SUPPORT

• These are universal parts, meaning they have no direct fitment to any particular vehicle. Custom welding and fabrication is required.
• Since these are brushed for a high-quality appearance, special prep/clean procedures must be adhered to for proper welding.
• Install photos depict possible usage of our Universal Exhaust Components. Only contains the item listed above.

Experience the ECS Tuning Wheel Spacer Fitment Kit Rent & Return Program

Explore the ECS Tuning Wheel Spacer Fitment Kit Rent & Return program, designed for Euro vehicles, offering the flexibility to experiment with wheel spacers hassle-free. Test fit various thickness spacers and bolt patterns to optimize your wheel fitment without commitment.

• Easy FedEx return with included shipping label (available for contiguous US customers)
• Receive a $110.00 account credit upon returning the complete fitment kit
• Contains 5 different thickness spacers for test fitting
• Accommodates 5 different bolt patterns: 4X100, 5X100, 5X112, 5X120, 5X130mm
• Each kit includes various nuts and studs for compatibility with different applications
• Designed for test fitting purposes only; cannot be used for driving

*$110.00 account credit will be applied on receipt of complete, serviceable Wheel Spacer Fitment Kit. Partial credit may be issued in the event of an incomplete kit.

**Vehicles with pre-installed wheel studs or stud conversions will need studs removed before test-fit as the spacers do not have all lug holes available**