Please ensure your correct model is selected
Give your factory clutch a heavier motorsport feel or make your extremely tough clutch more drivable! If you have an E36 there is absolutely no reason you don't have this clutch pedal! Your factory E36 clutch pedal is made of flimsy plastic with no adjustment at all, leaving you to the mercy of the clutch you have.
Our Turner Performance Adjustable Clutch Pedal is a rigid design that gives you the ability to fully adjust your clutch feel and performance. With both upper and lower adjustments this is the best pedal on the market to fine tune your clutch pedal just the way you like it. The upper eccentric provides an adjustable pedal ratio to fine tune clutch pedal effort(how heavy the pedal feels). The lower adjustment is to change the position of the clutch assist spring, this allows you to choose where the clutch assisting spring engages. Changing where the spring engages will move the area of tension on your clutch from lower, middle to higher for maximum adjustment.
Your race car no longer needs to have a clutch that makes the car undriveable on the street. Your track car can now be your daily driver or weekend cruiser.
Features:
Adjustable throw
Capable of quicker shifts
Three lower mounting points for the spring to adjust where the assistance engages
Eccentric mount for master cylinder to adjust leverage ratio and pedal feel(weight/force needed to engage the clutch)
Self lubricating bronze bushings
All necessary hardware required for installation
Pedal body and pedal are constructed from 6061-T6 aluminum and type II black anodized for a great finish
NOTE: This Clutch Pedal does not include the Compression spring and the original spring must be reused. If you'd like to purchase a new spring, please see:
35311162505 - Non-M E36 - T#64615
21522227764 - E36 M3 - T#21753
If allowed in the rules these solid aluminum transmission mounts offer many advantages over a urethane or Delrin mounts. It's no wonder that these mounts have found their way into the top BMW racers in the country. These are machined from solid aluminum and have zero deflection, engine torque will cause a rubber or urethane mount to flex or deflect allowing more torque to passed through the drive line (instead of being wasted winding up the mount). This puts the shift linkages in better consistent alignment. And unlike rubber or urethane the aluminum has zero wear and is not affected by leaking oil or other fluids so this is likely the last set of transmission mounts you will ever need. We very strongly recommend using the solid transmission and engine mounts together as a complete kit, mixing a rubber mount with a metal mount will cause undue stress on the mounting points and will lead to a failure. We never advise using a solid mount unless a corresponding solid mount is also used.
These are a no-compromise design for all-out racing use, full solid aluminum mounts should not be used on street-driven cars since there is no material to absorb vibration making these quite harsh for regular street use (track cars don't care about noise).
Product features and benefits:
This item fits the following BMWs:
1989-1995 E34 BMW 525i 530i 535i 540i M5
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1997-2003 E39 BMW 525i 528i 530i 540i M5
1999-2005 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci M3
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
If allowed in the rules these solid aluminum engine and transmission mounts offer many advantages over a urethane or Delrin mounts. It's no wonder that these mounts have found their way into the top BMW racers in the country. We originally developed these mounts for E36 and E46 World Challenge racing but they also work perfect in BMW Modified and SCCA club racing and SpecE46 (SE46). These are machined from solid aluminum and have zero deflection. The engine torque will cause a rubber or urethane mount to flex or deflect. The stiffer the material the less movement there is and the more torque is passed through the driveline (instead of being wasted winding up the mount). At the transmission end the flex-free solid mounts will give smoother, crisper shifts since the transmission is no longer dancing on the pliable mount. This puts the shift linkages in better consistent alignment. And unlike rubber or urethane the aluminum has zero wear and is not affected by leaking oil or other fluids so this is likely the last set of motor and transmission mounts you will ever need. We have designed these mounts so the engine is 5mm lower and the transmission is 1mm lower than the factory mounts. This helps lower the center of gravity for better balance and handling. We very strongly recommend using the transmission and engine mounts together as a complete kit. Mixing a rubber mount with a metal mount will cause undue stress on the mouting points and will lead to a failure. We never advise using a solid mount unless a corresponding solid mount is also used. This kit fits the E36, E46, Z3, and Z4 6 cylinder models listed below, including M3 models.
New for your 6-cylinder Z3 is our Dual Shear Selector Rod (DSSR) to deliver a more controlled and tighter shifting experience over the factory selector rod. Pair our Z3 DSSR with our upgraded poly rear shifter bushing for the full upgraded shifting experience. This DSSR is designed for Z3 models that have the selector rod p# 25111222780.
Upgrade from your single connection selector rod to a dual shear selector rod or DSSR for a stronger connection and an overall better shifting experience. The factory BMW selector rod is made of hollow aluminum tubing and attaches to both the shifter and transmission from one side utilizing a pin-and-clip design. The factory single-side attachment only has a small amount of surface area contacting both the shifter and transmission selector which relies directly on the connecting pin to do all of the shifting and control, this can cause a loose and/or lackluster experience when shifting gears or shaking your shifter in neutral. Your new Turner DSSR features a much larger contacting surface to both the shifter and transmission, not only does the upgraded DSSR have larger faces contacting your shift components but it also features double the amount of mounting surfaces. This dual shear selector rod hugs your shift lever and selector tight from both sides and eliminates deflection and sloppiness for the best shifting experience possible.
Features and benefits:
Provides an increased shift feel by reducing deflection and play in the linkage.
Works with factory and aftermarket Turner shifters
Maintains stock 389mm length for stock shift knob location
Precision machined pins for perfect fit
Manufactured from 303 stainless steel for superior corrosion resistance
Design:
Designed to maintain 5 degrees of lean for the shift lever toward the driver
Replacement for 25111222780 (E36/7 6-cylinder cars)
Laser-etched Turner logo
Product development:
Our shifter components are designed, engineered, tested, and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.
The ZF S5D 320Z 5-speed transmission is known for its robust design, exceptional durability, and impressive power-handling capability. Unfortunately, as these transmissions age, shifter-related issues have become increasingly common. Problems such as difficulty selecting gears, a sticky shifter, or a decline in shift quality are often the result of worn detent springs, pins, and bushings. These components are essential for precise gear engagement and proper shifter centering, making their replacement a critical step in maintaining optimal performance.
Replacing detents requires specialized tools known as "drifts," which are notoriously hard to find. Fortunately, we've developed a complete Detent Tool Kit, featuring five precision-engineered drifts designed for exact fitment in the ZF transmission's detent bores. This toolset makes detent replacement straightforward and minimizes the risk of damage to internal transmission components.
Features
Complete Tool Kit: Includes five precision-machined drifts specifically designed for the ZF 5-speed transmission’s detent bores and caps. Hassle-Free Detent Replacement: Simplifies the process of removing and installing detents with professional-grade precision. Protects Your Investment: Reduces the risk of damaging internal transmission components during service. Durable Construction: Made from heavy-duty 1045 steel for exceptional strength and long-lasting reliability.
