BMW Engine Parts for BMW Z3 (1996-2002)

This is an OEM INA tensioner pulley, also known as the adjusting pulley and lower pulley. This pulley is mounted on the belt tensioner near the center of the belt assembly. The upper and lower pulleys are known to be the primary sources for 'belt squealing'. This pulley is also encased in rubber which will crack over time. If left without service the rubber could fail completely, chucking the belt and leaving you stranded. Replacement is a very simple procedure and can be done anytime the fan is off the engine (belt replacement, water pump service, alternator replacement, etc).

This pulley is mounted along with the hydraulic belt tensioner but can be replaced on its own. It is used for the main drive belt on the M50-M54 family engines (M50, M50TU, M52, S52, M52TU, M54, M56, and S54 engines). This is the same belt that covers the water pump/alternator/power steering systems. Replacement is a very easy procedure (requires fan removal) and will have your engine purring in no time. Belt replacement is strongly recommended at the same time. If you have a mechanical belt tensioner, the pulley can only be replaced with a new tensioner.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

If you need the hydraulic belt tensioner, click here.

This item is 70mm Diameter. Please check the diameter before ordering.

This tensioner pulley fits the following BMWs:
1991-1995 E34 525i (M50 engine)
1992-1999 E36 325i, 325is, 328i, 328is, 323is
1995-1999 E36 M3 (M3 3.0 & M3 3.2 liter)
1997-2003 E39 525i, 528i, 530i - Only for Hydraulic Tensioner
1999-2000 E46 323i, 323Ci, 328i, 328Ci - Only for Hydraulic Tensioner
2001-2005 E46 325i, 325Ci, 325xi, 330i, 330Ci, 330xi - Only for Hydraulic Tensioner
2001-2006 E46 M3 coupe & convertible - Only for Hydraulic Tensioner
2000-2006 X5 3.0 liter (E53 chassis)
2004 E60 525i, 530i (M54 engine)
1997-2002 Z3 & MZ3 2.5, 2.8, 3.0, M Roadster, M Coupe
2003-2009 Z4 M Coupe and Roadster

When servicing your vehicle's VANOS system, get the job done easier with this socket specifically designed for the removal of the VANOS solenoid.

Features:

• 85mm from end to end
• 1/2" drive 
• 32mm with a depth of 70mm.

Turner Motorsport BMW Timing Chain Tensioner Replacement

Introducing the BMW Timing Chain Tensioner Replacement by Turner Motorsport, a vital component to maintain optimal tension and prevent timing chain issues. Engineered for reliability, this replacement ensures the proper functioning of your cam gears and crank, preventing potential engine damage.

Benefits:

• Crucial for timing chain tension
• Prevents chain skipping
• Safeguards against catastrophic engine damage
• Quiets noisy chains for a smoother engine operation

Replace your BMW's timing chain tensioner with this Turner Motorsport solution to keep your engine running smoothly.

Schwaben BMW Vanos Adjustment - Wrench is essential for the precise installation of a new or rebuilt VANOS unit on your BMW. This specialized tool ensures that the VANOS system is correctly adjusted, which can significantly impact your vehicle's performance and overall operation once reassembled. Proper VANOS adjustment is crucial for maintaining optimal engine timing and efficiency.

• Precision Tool: Designed specifically for BMW VANOS unit adjustments, ensuring accurate installation.
• Improved Performance: Helps maintain optimal engine timing and efficiency, leading to better vehicle performance.
• Essential for Rebuilds: Critical for the installation of new or rebuilt VANOS units, preventing potential issues during reassembly.
• Durable Construction: Built to last, providing reliable performance through multiple uses.

Enhance BMW engine maintenance with the Crankshaft Socket - B46 / B48 / B58, an essential tool for effortless engine rotation during timing jobs or valve timing adjustments.

• Specifically designed for BMW B46, B48, and B58 engines
• Facilitates easy and precise engine rotation
• Ideal for timing jobs and valve timing adjustments
• Ensures proper alignment and maintenance accuracy

Upgrade your BMW maintenance toolkit with the Crankshaft Socket, providing the necessary precision for timing tasks and valve adjustments on B46, B48, and B58 engines.

This gauge ensures that the inlet and exhaust cams are aligned perfectly. Make sure the edges are on the correct sides of the cylinder head before using.

Includes two alignment pin's which is ideal for inspection and servicing the motor with the timing chain still attached. If you are going to be removing the timing chain for service, you will need to lock both cams. 

The Ultimate kit includes every thing the standard kit does along with, a second alignment bridge, flywheel lock pin, VANOS alignment tools. and 4 bolt crank socket.

This tool fits all S54 powered BMW, including: 
2001-2006 E46 BMW M3
2001-2002 E36/7 BMW Z3M Coupe Z3M Roadster
2006-2008 E85/6 BMW Z4M Coupe Z4M Roadster
 

This is an OEM INA AC Belt Tensioner with pulley for all 2001-2006 E46 M3, as well as all 1999-2002 non-M E46 3 series models. These belt tensioner units are known to fail, and include the tensioner pulley (as shown).

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This Air Conditioning / AC Belt Tensioner with Pulley fits:
1999-2000 E46 3 Series 323i, 323Ci, 328i, 328Ci
2001-2002 E46 3 Series 325i, 325Ci, 330i, 330Ci
2001-2006 E46 M3 coupe & convertible

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Looking to update your old torque wrenches? The Schwaben 3/8" Drive Digital Torque Wrench is your answer. 

This digital torque wrench uses an easy-to-read display to show torque amounts and settings, features a push button release, reversible 3/8" drive, 45 tooth ratchet head, and a comfortable no-slip grip and adjustment wheel.

Specifications:

• Setting Range: 45-220 ft lbs (60-300 Nm)
• Display Units: ft-lbs, N-m, Inch-lbs, cm-kg2, and m-kg
• Size: 22" (550mm) length for easy leverage
• Accuracy: +- 3%
• Include blow molded holding case
• Requires one 3V CR2030 battery (included)

For Alternator / Water Pump Belt

Hydraulic Belt Tensioner for E36, E46, E39 6-cyl models. This is the oil-filled tensioner that keeps the main drive belt in the proper tension. Over time the piston seals inside allow fluid to leak out. The tensioner becomes frozen or inoperable. Replacement is the best corrective action to take. This can be done during any belt or pulley service or anytime the fan is off the engine.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

NOTE: These BMW's may have been equipped with either a mechanical or hydraulic tensioner. Only for cars with Hydraulic Belt Tensioners. Please check before ordering.

This tensioner pulley fits the following BMWs:
1991-1995 E34 525i (M50 engine)
1992-1999 E36 325i, 325is, 328i, 328is, 323is
1995-1999 E36 M3 (M3 3.0 & M3 3.2 liter)
1997-2003 E39 525i, 528i, 530i
1999-2000 E46 323i, 323Ci, 328i, 328Ci
2001-2005 E46 325i, 325Ci, 325xi, 330i, 330Ci, 330xi
2001-2006 E46 M3 coupe & convertible
2000-2006 X5 3.0 liter (E53 chassis)
2006 525i, 530i(M54 engine)
1997-2002 Z3 & MZ3 2.8, M Roadster, M Coupe
2003-2009 Z4 M Coupe and Roadster

This timing chain tensioner keeps the tension rail properly positioned on the BMW M42 and M44 4 cylinder engine.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1990-1991 E30 BMW 318i 318is 318ic
1992-1998 E36 BMW 318i 318is 318ti 318ic
1997-1999 Z3 BMW Z3 1.9

BMS Billet Spark Plug Gapper Tool - 14mm is an essential tool for achieving accurate and consistent spark plug gapping, ideal for automotive enthusiasts and professional mechanics alike. This precision tool helps maintain optimal plug performance by providing reliable, consistent gaps. Available in both 14mm and 12mm plug thread sizes, this tool is proudly made in the USA to deliver durability and precision.

• Precisely gaps spark plugs for enhanced engine performance and efficiency
• Speeds up the gapping process while ensuring accuracy and uniformity
• Available in two sizes (14mm and 12mm) for a wider range of compatibility
• Optional specialty feeler gauge included with 4 blades in thicknesses of .018, .020, .022, and .024
• Made in the USA for premium quality and durability

The Schwaben Universal Piston Ring Compressor is a must-have tool for easily and precisely compressing piston rings.

Standing 4 inches high, this compressor features two spring steel bands that provide evenly distributed pressure across all piston rings, accommodating pistons ranging from 60 mm to 175 mm in diameter. Designed for use on all passenger vehicles, this tool ensures efficient and reliable compression.

**Note** For the Schwaben Piston Ring Filer, check out T25805754!

Key Features:

• Versatile Capacity: Handles most pistons from 60 mm to 175 mm in diameter.
• Even Pressure Distribution: Two spring steel bands equally distribute tension for easy and effective compression.
• Durable Construction: Made from sheet steel for long-lasting performance.
• User-Friendly: Features an easy thumb release locking mechanism for quick and secure operation.
• Universal Application: Suitable for use on all passenger vehicles.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Perfect for any job when it comes to keeping your hands clean and protected.

Features:

• High dexterity
• Elastic hook and loop strap
• Textured latex finger tips for grip
• Breathable material

Schwaben Professional Mechanic's Work Gloves provide exceptional hand protection with a perfect balance of durability and comfort.

Designed for precision, these gloves offer high dexterity, making it easy to handle even the smallest parts. The tailored elastic cuff with a hook-and-loop closure ensures a secure and comfortable fit.

The textured latex coating on the palm and fingertips delivers superior grip and tactile feedback, while the breathable spandex backing and knit top allow for all-day comfort.

The durable synthetic leather palm enhances longevity, and the unique graphic design reflects the drifting culture of Euro car enthusiasts.

Note: See manufacturers information tab for sizing chart.

Key Features:

• High Dexterity: Perfect for picking up small parts with ease.
• Secure Fit: Tailored elastic cuff with a hook-and-loop closure.
• Enhanced Grip: Textured latex coating on palm and fingertips.
• All-Day Comfort: Breathable spandex backing and knit top.
• Durable Design: Synthetic leather palm for extended wear.
• Unique Style: Graphic design inspired by the drifting culture of Euro owners.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Battery Terminal brush uses the external brush to clean the cable clamps and the internal brush to clean the battery posts. Made from high Impact plastic body to eliminate tool corrosion.

Keeping the connection clean is an important part of making sure your battery is transferring the proper voltage during startup.