BMW Engine Parts for BMW Z3 (1996-2002)

Maintaining optimal engine oil levels is crucial for peak performance in your BMW. Leaks can occur between oil change intervals, leading to dangerously low oil levels. The valve cover is a frequent culprit for such leaks due to gasket degradation from years of exposure to temperature fluctuations. Replace your valve cover to ensure the retention of engine oil within your vehicle.

Key benefits of replacing the valve cover include:

• Preventing oil leaks that could lead to low oil levels.
• Preserving engine performance and longevity.
• Avoiding potential engine damage from insufficient oil.

Ensure your BMW's engine operates smoothly by replacing the valve cover to contain the engine oil effectively.

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On older BMWs, the engine ground strap is a thin, non-insulated cable that spans from the engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for E30 (318i/is), E36, E39, E46, and others Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12421737755 and 12421714262.

If there is a large amount of oil on the sides of the engine or if you can smell burning oil, chances are it's a bad valve cover gasket. The gasket fails and allows oil to seep down onto the side of the engine and other parts causing a mess and reducing the amount of oil in your engine. This replacement gasket from Elring is perfect to prevent any further oil leaks.

Includes the following Seals:

• Valve cover gasket
• Spark plug seals

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following engines:
M42
M44

After the introduction of the M52TU/M54 engines, BMW observed an uptick in CCV-related issues, especially in cold regions. Vehicles operating in extremely low temperatures often encountered a blockage in the CCV dipstick hose, leading to elevated crankcase pressure and visible blue smoke from the exhaust. To address this issue, BMW introduced cold climate-specific hoses with foam insulation, preventing condensation and facilitating quicker oil warm-up. This kit incorporates top-notch reproduction cold climate hoses to ensure optimal CCV performance across all weather conditions.

The crankcase ventilation valve, known as the oil separator, PCV, CCV, or crankcase pressure regulator valve, plays a vital role in redirecting oil from your vehicle's intake system back into the engine oil pan. This system comprises numerous plastic and rubber hoses, prone to damage due to prolonged exposure to chemicals and heat.

Designed to tackle or prevent impending CCV system failures, this kit includes four foam-insulated hoses made from durable plastic capable of withstanding heat fluctuations and chemical exposure. Additionally, a new ventilation valve is included for a comprehensive and long-lasting repair solution.

Signs indicating the need for crankcase ventilation system replacement include:

Whistling sounds from the intake manifold, caused by crankcase pressure venting through holes in the CCV hoses. Blue smoke emitting from the tailpipe, indicating oil consumption. Excessive oil usage. Milky or yellowish buildup under the oil cap, suggesting condensation due to ventilation valve malfunction. If you're experiencing misfires, lean fuel codes, decreased fuel efficiency, or noticeable oil consumption, it's advisable to overhaul your crankcase ventilation system. Opt for this reliable system from Febi-Bilstein for a repair that meets factory standards and ensures consistent performance.

A beautiful addition and durable upgrade for your engine

Tired of staring at that bright red plastic oil dipstick? Waiting for a way to add a nice touch to your engine bay without going over the top? ECS Tuning is proud to announce the billet aluminum oil dipstick! Designed to OE specifications with an easy-to-read fill line, offered in three different finishes. Available in black, polished, or clear anodized, we have an offering for every type of enthusiast. Not only does it look better, but also performs better. Because of the durability, it is easier to insert than the factory ribbon dipstick. So, no more fighting with your dipstick to re-install it.

The main reason all of the VANOS units will eventually fail is because the material used for the sealing rings from the factory is not designed for that type of environment. When this happens the only option that BMW leaves you with is buying a new and expensive VANOS unit with the same sealing rings that failed in your original unit.

The VANOS system found in BMW engines is a great feature (when it’s working properly), keeping your power curve smooth and responsive especially in lower to mid RPM range. What usually goes unnoticed is the gradual loss of power within this range as the vehicle's age due to slowly failing seals within the VANOS unit. The way the VANOS system works is based off of oil pressure triggered by a solenoid that allows for a small range of timing degree adjustment, this is where the power curve is affected. When the seals begin to fail (all of them do) there is less pressure to advance the timing reducing the power in that low to mid range. Because this happens slowly it's very hard to notice a difference until you refresh your VANOS unit, then you easily realize the response you've been missing.

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

While you're replacing the seals in your VANOS unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy VANOS clatter.

Seals & O-rings:

The seals  were the main focus of this project since the OE units are built with Buna-N rubber o-rings instead of the ECS supplied Viton rubber o-rings. The Buna-N material quickly hardens from the heat and chemical exposure within the engine, where the Viton is significantly more resistant to these chemicals. This knowledge was also used when it came to the commonly failed o-rings found on the VANOS seal plate, replaced at the solenoid.

Rattle Repair:

When it comes to the VANOS rattle this is commonly described as "marbles in a can", and can be heard throughout the different RPM ranges depending on the engine. These upgraded rings and washers are precision ground from hardened steel to resist wear and deformation keeping your VANOS rattle free. The rattle repair tools are designed specifically for this VANOS anti-rattle repair, design from hardened steel to stand up to the job. Designed to perfectly follow the splines of the shaft for a tight grip when applying the necessary torque to disassemble & reassemble the VANOS transfer gear. The keyed socket was designed with the intent to use a "common" wrench so this can be completed at home in your garage.    

When Servicing your VANOS unit we recommend getting everything you need to replace on the way to service which includes an oil change and valve cover gasket set. Fresh oil and gaskets is the best way to start off a fresh rebuild of any kind giving you the maximum performance of your freshly serviced components.

Don't forget to check out our rebuild PDF to make sure you have everything to get the job done and eliminate the rebuild guess work.

This item fits the following BMWs: 
2000-2001 E46 3 Series M3 M3 Convertible 2000-2006 
2001-2002 Z3 Roadster / Coupe Z3 M Roadster Z3 M Coupe w S54 Engine 
2006-2008 E86 E86 Z4 Z4 M Roadster Z4 M Coupe

These WPC-treated bearings are the best we have seen! WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are original equipment KS bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

This item fits the following BMWs: 
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix 
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1982-1988 E28 BMW 528e
1989-1995 E34 BMW 525i
1997-2003 E39 BMW 525i 528i 530i
2004-2005 E60 BMW 525i 530i 
2004-2006 E83 BMW X3 2.5i X3 3.0i 
2000-2006 E53 BMW X5 3.0i 
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i 

The head gasket is exposed to high pressure and heat for extremely long periods of time. Over a long period of time, these may develop a slight oil leak and must be replaced ASAP to prevent damage to the engine. It should also be replaced any time that the engine head is removed to ensure the best seal possible.

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following BMW engines:
M52 2.5L 2.8L, M54 2.5L 3.0L

Upgrade your vehicle's lighting with Ziza Platinum White 9006 bulbs, replacing stock bulbs with a clean white light for enhanced visibility. As a leading manufacturer and distributor of performance automotive lighting products, Ziza brings innovation to LED bulbs, HID bulbs, clear lens side markers, smoked lens side markers, and more. Take your automotive lighting to the next level with Ziza's high-quality products.

This non-DOT approved product is for Off-road/Track use only. Not approved for legal street use

If there is a large amount of oil on the sides of the engine or if you can smell burning oil, chances are it's a bad valve cover gasket. The gasket fails and allows oil to seep down onto the side of the engine and other parts causing a mess and reducing the amount of oil in your engine. This replacement gasket from Elring is perfect to prevent any further oil leaks.

Includes everything needed to re-seal your engine's head.

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following engines:
M52 2.5L 2.8L (up to 09/1998)