Find Parts That Fit Your Vehicle

Sensors

When it comes to BMW and Mini, there is no shortage of sensors on your vehicle! Below you can find many of the crucial sensors that lead to error messages and check engine lights being displayed when a fault has occurred. Get your BMW/MINI back on the road with these Genuine BMW or high-quality OEM parts.
Sort By:

Genuine BMW Pulse Generator/Crankshaft Position Sensor - 12141726065 - E36,E36 M3
Genuine BMW - Corporate Logo
T#:185064
Part#: 12141726065
In Stock
$181.95
Free Shipping on orders $49 and up
$181.95
Free Shipping on orders $49 and up

The Crankshaft Position Sensor measures the speed and position of the crankshaft to determine the proper fuel and timing requirement for the best performance.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Pulse Generator
This item fits the following BMW Chassis:
E36 M3,E36

Fits BMW Engines including:
M50,S50

 

Show More Show Less
OBDI Conversion Part - Water Temp Sensor Wiring Adaptor
Turner Motorsport - Corporate Logo
T#:508
Part#: TEN9989M50
Inventory On Order, ETA May 13, 2021
Sale - Save 10% $60.95
$54.86
Free Shipping
Sale - Save 10% $60.95
$54.86
Free Shipping
Made in the USA The TMS Water Temp Sensor Wiring Adaptor is needed when you are upgrading to OBD-I (1992-1995 components) on a 3.2 or 2.8 liter engine. These earlier engines use two separate water temp sensors in the head, one for the ECU and one for the instrument cluster. Most of the 3.2 and some of the 2.8 liter engines do not have two holes drilled in the head for the early water temp sensors. This is due to the fact that the 3.2 and 2.8 engines used a combined water temp sensor. So we designed a easy to use plug and play wiring harness. The benefits are: No cutting and splicing, no trying to fine plugs and pins. We also suggest using TMS "3.2 in a 3.0" Coolant Hose Adapter P/N: TEN9931007 to make your life easier.
Show More Show Less
OEM VDO MAP Sensor -- N20 N26 S55 S63
Continental - Corporate Logo
T#:393689
Part#: 13627843531
In Stock
$65.06
Free Shipping on orders $49 and up
This is a high quality replacement OEM VDO Manifold Absolute Pressure sensor Located on the charge air cooler. The MAP controls the amount of fuel that goes through the injectors based on the pressure of air at the intake manifold.
Show More Show Less

Turner Plug-and-Play IAT Relocation Kit
Turner Motorsport - Corporate Logo
T#:391751
Part#: 014579TMS
Inventory On Order, ETA Jun 14, 2021
Sale - Save 8% $116.90
Starting at $107.41
Free Shipping
Sale - Save 8% $116.90
Starting at $107.41
Free Shipping

All vehicles will lose some degree of performance due to heat soak under the right operating conditions.  Engine management systems constantly monitor operating conditions and modifying parameters based on sensor inputs. BMW integrated the intake air temp sensor in the MAF housing on models such as the E39 M5, and, being sandwiched behind a hot radiator and in some applications next to an even hotter valve cover, this is less than ideal for performance applications. Absorbing excess heat from its surroundings, the MAF can’t shed it fast enough, and the ECU reads an inaccurately high intake air temperature. Compensating for this false hot air measurement, the ECU pulls timing and runs a richer fuel mixture, resulting in a significant loss of torque.

What can you do?  Locate an intake air temp sensor in a location where it can properly measure incoming air temps and where it's less prone to heat soak. Mounting the sensor further away from the heat source and isolating it from the MAF housing, it can both resist the effects of heat soak longer and respond to temperature changes more quickly.  The result is you’ll experience reduced torque loss and more consistent power output when you’re pushing your engine hard. 

The Turner engineering team was initially skeptical of the claimed performance benefits of this modification. They first set out validate the functionality and performance benefit of a temp sensor relocation. Replicating stop-and-go traffic heat soak in a 2001 540i was a simple task in a controlled environment - their dynometer. First the car was heat soaked to simulate being stuck in traffic or moving at low speeds by running the car four times on the dyno with the dyno's cooling fans disabled. The fans were then turned on for three more runs to observe the recovery rate once air flow was reintroduced. The test: following this procedure once with a stock IAT, and once with their relocation kit in place. 

The result? Turner recovered 11lb-ft torque at 2500rpm through use of their relocation kit, with even greater recovery to be found for M5 owners. Here are the heat soak-related torque losses Turner experienced:

Stock IAT location:
18rwtq at 2500rpm
10rwtq at 3000rpm
9rwtq at 3700rpm

Turner IAT Relocation:
7rwtq at 2500rpm
5rwtq at 3000rpm
5rwtq at 3700rpm

**Click here for installation instructions**

The Turner engineering team designed a complete plug and play kit (unlike all other options on the market) that makes for quick, easy, and reversible installation. Weather-sealed connectors keep out the elements, while sheathed wiring offers a clean appearance underhood. With a harness nearly 3 feet long - the Turner IAT relocation kit offers flexibility in positioning, but not too long that you're left with unsightly excess wiring. Turner recommends positioning the sensor in a location away from engine heat, but still within the intake ducting to achieve accurate intake temp readings - such as the far side of the base of the airbox. Vehicles with cold air intakes with cone-style filters can even position the sensor in the end of the filter. Simply drill a hole in your (cool) location of choice and plug in the harness. More information including installation instructions and some good examples of sensor mounting locations can be found in our DIY PDF. 

We include everything you need to relocate your IAT, just select your desired sensor brand below - Genuine BMW or original equipment Beru.

Also the perfect plug-n-play option for anyone looking to upgrade their intake to utilize an Alpha-N tune!

Note for vehicles with M62 engine: applicable to 1999 and up

Show More Show Less

Oil Level Sensor - E46 E39 E60 E38 X3 X5 Z3 Z4 Z8
Bremmen Parts - Corporate Logo
T#:395203
Part#: 12617508003
In Stock
Sale - Save 20% $39.95
$31.96
Free Shipping on orders $49 and up
Sale - Save 20% $39.95
$31.96
Free Shipping on orders $49 and up
This is the oil level sensor / sender for BMW E46 E39 E60 E38 X3 X5 Z3 Z4 Z8.When this part fails it will illuminate a check light on the dash which indicates it needs to be replaced. Includes o-ring. This item fits the following BMWs: 1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330xi M3 2008+ E90 BMW 335d 1999-2003 E39 BMW 528i 525i 530i M5 1998-2003 E39 BMW 540i 2004-2005 E60 BMW 525i 530i 1998-2001 E38 BMW 740i 740il 750il 2004-2006 E85 BMW X3 2.5i X3 3.0i 2000-2006 E53 BMW X5 3.0i 2000-2003 E53 BMW X5 4.4i X5 4.6is 1999-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i 2001-2002 Z3 BMW Z3 M Roadster Z3 M Coupe 2003-2006 Z4 BMW Z4 2.5i Z4 3.0i 2000-2003 E52 BMW Z8
Show More Show Less