BMW Tools & Specialty Equipment for BMW E12 530i M30 3.0L

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible ½-inch drive click-to-stop
• Torque range of 10 to 150 ft-lb
• Accurate to within +/-4%
• 18 inches in length with a convenient carry case

Our aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

Better still, order two: one for your garage and another for the emergency tool kit in you trunk.

The Foxwell T20 TPMS sensor integrates both 315 MHz and 433 MHz frequencies, replacing more than 99% of OEM direct TPMS sensors on the market. The all-new, high-precision air valve prevents air leakage and provides a durable seal - an upgrade over the outgoing T10. Its proprietary sensor body features a long-lasting, lightweight 3V battery and supports unlimited wireless programming. Sensors can easily be activated and programmed with the Foxwell T2000 TPMS Service Tool (T#36811799).

Features:

Rubber valve stem Supports 315MHz and 433MHz frequencies High-precision air valve to avoid air leakage 0-30° adjustability Built-in battery with an extended service life (more than 5 years) Temperature reading range of -40°F to 257°F Pressure monitoring range of 0 to 130.53 psi 12G weight

If you're removing trim panels and don't want to scratch or break any pieces then this is a must have. Formed for precision and constructed from plastic to be gentle with the finish.

Features:

•  Wide type remover
• Pull type remover
•  Handy remover
• Narrow type remover
• Upholstery Clip remover
• Angled Clip Panel Remover
• Fork Tip Flat Clip Panel Remover
• Clip Panel Remover
• Sharp Tip Flat Clip Remover
• Panel Remover
• Blunt Tip Flat Clip Panel Remover

This large socket is the perfect tool for axle nuts when servicing the axle shafts or wheel bearings.

Features:

• ½-inch drive 46mm 12-point socket
• Specially hardened to take the added abuse from a impact gun
• Coated for added protection and so you can tell it apart from non impact rated sockets
• 75mm depth  to accommodate many applications and different length shafts
• Made of durable chrome moly steel

Custom exhaust work in the plans? The Schwaben Exhaust Pipe Cutter will help you cut out old pipe or cut down new pipe with ease. It can cut any pipes from 3/4" to 3" in diameter and cuts pipe with only 1/4 turn adjustments, thanks to 15 blades that effectively cut the entire pipe with little movement. This is great for tight to reach places that prevents you from using more traditional non-specialty tools.

Features:

• Cuts from 3/4" pipe up to 3" pipe
• 15 cutting blades
• Rubber covered handles for grip and comfort

The Schwaben Dual Temperature Heat Gun Kit is the ideal tool for stripping paint, removing decals, shrinking wire wrap, etc. The heat gun has a switch which allows for two different heat settings (572F and 932F).

Features:

Four airflow adapters, 1pc Large Deflector Nozzle, 1pc Reduction Nozzle, 1pc Small Deflector Nozzle, and 1pc Reflector Nozzle.
Voltage 120C, 60 HZ
Amps 12.5A
Two heat settings: Low Heat up to 572 Degree F. High Heat 932 Degree F.
Air Volume: Low Heat: 10 cfm (280L/min) High Heat: 17 cfm (480 L/min)
Wattage: Low Heat: 1000W High Heat: 1500W
Has 6.75 Ft cord.
Built in hook to hang on wall.
For California Prop 65 warning see: www.P65Warnings.ca.gov. and photo below.

All the right bits in one box. The perfect assortment to keep the job going.

Features:

• 10 fractional SAE hex, 9 Torx® tamper-proof, 9 Torx®

• 9 Metric hex bits, 9 slotted bits, 8 Pozi-drive, 8 Phillips, 4 square-recess, 4 tri-wing

• 3 spline, 3 Torq, 3 clutch, wing-nut driver, magnetic bit holder and socket bit holder

• Made of hardened Chrome Vanadium steel for years of dependable use

• Packaged in a handy blow molded case with individually marked bit slots for easy organization

Take one wrench, not two to your next fluid service. The Schwaben Service Wrench fits both crankcase and drain plugs in BMW, Mercedes, and other European vehicles.

Features:

• Six-point 17mm box end won’t round off engine oil drain plugs
• Hardened 14mm hex at the opposite end fits many transmission fill and drain plugs
• Made of vanadium steel with polished chrome finish
• Long handle for added leverage.

Fits most vehicles with M10, M20, M30, M42, M44, M50, M52, M54, M56, M70, S14, S38, S50, S52 and S70.

Application note: Please verify the exact size of the transmission and differential plugs in your car. BMW has used both 14 and 17mm plugs in some vehicles. 

Having a nice quality set of extensions always comes in handy when working on BMW's. With the slanted position of most engines and the tight engine bay, there almost always a hole for the extension to reach into and easily remove the fastener.

Features:

• 3/8" drive extension set features high quality tool steel with an easy to wipe clean satin finish
• Knurled section on shaft allows for easy turning by hand when needed
• Size range - 1.5",3",6",10" with a convenient storage tray

Schwaben 8-Pc ATF Adapter Set is designed to provide a versatile solution for working with automatic transmission fluid (ATF) systems. This comprehensive adapter set includes multiple sizes to ensure compatibility with a wide range of vehicles, making it an essential tool for automotive professionals and DIY enthusiasts alike.

• Versatile Compatibility: Includes multiple adapters to fit various vehicle makes and models, making it a valuable addition to any automotive toolkit.
• High-Quality Construction: Made from durable materials to withstand the rigors of professional use and provide reliable performance.
• Enhanced Precision: Ensures accurate fluid transfer and servicing by providing the correct adapter size for different ATF systems.
• Convenient Set: Contains all necessary adapters for a comprehensive solution, eliminating the need for separate purchases.
• Easy to Use: Designed for straightforward application, allowing for efficient and effective ATF service and maintenance.

It only takes a gust of wind to have your hood crashing down on your head, or if you have a carbon fiber hood and no longer have the gas struts than this could be what you need.

 This hood prop is adjustable, lightweight, and sturdy making it easy to keep out of the way in the trunk so it's there whenever you need it.