BMW Tools & Specialty Equipment for BMW E12 530i M30 3.0L

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible ½-inch drive click-to-stop
• Torque range of 10 to 150 ft-lb
• Accurate to within +/-4%
• 18 inches in length with a convenient carry case

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible 3/8"-inch drive click-to-stop
• Torque range of 5 to 80 ft-lb
• Accurate to within +/-4%

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

Tired of busting your knuckles from old hardened exhaust hangers?

This Schwaben tool removes the hanger by pressing on the steel hanger bracket and pulling the rubber hanger in one motion. Self centering force pin locks onto the pin while the flat paddle pulls off the rubber hanger from behind. Slim profile and a 25 degree offset works in tight areas.

Safety is always the most important factor when it comes to working under your car, jack stands are highly recommended. 

Features:

• Ultra light  jack stands only weigh 4.7 lbs each
• All aluminum construction with heavy-duty  flanged bases to safely stabilize loads
• 6 locking positions for a secure load in multiple heights
• Extra heavy duty load pin at .584 in. diameter with a posi lock ball to insure it stays in place
• Min. Height is 10.6
• Max Height is 15.4"
• Large 7" diameter base
• Outer support tube is 2-1/8" in diameter

If you're removing trim panels and don't want to scratch or break any pieces then this is a must have. Formed for precision and constructed from plastic to be gentle with the finish.

Features:

•  Wide type remover
• Pull type remover
•  Handy remover
• Narrow type remover
• Upholstery Clip remover
• Angled Clip Panel Remover
• Fork Tip Flat Clip Panel Remover
• Clip Panel Remover
• Sharp Tip Flat Clip Remover
• Panel Remover
• Blunt Tip Flat Clip Panel Remover

These weld protectors allow you to safely jack up your vehicle without crushing or bending any pinch welds. These will fit any jack and will work with many jack stands such as the Schwaben Aluminum Jack Stands.

Specifications:

• 3" wide
• 1" tall
• Single groove top
• Double grooved bottom

This complete set of extra deep sockets work great on cars equipped with extended studs. They also work as a long wheel nut socket for those deeply recessed nuts in wheels.

Features:

• 17mm, 19mm and 21mm socket in a sturdy blow molded case
• All sockets are 1/2" drive and a full 5-15/16 ( 150MM ) long
• Sockets are designed with inner bore to accept a 5" long stud

All the right bits in one box. The perfect assortment to keep the job going.

Features:

• 10 fractional SAE hex, 9 Torx® tamper-proof, 9 Torx®

• 9 Metric hex bits, 9 slotted bits, 8 Pozi-drive, 8 Phillips, 4 square-recess, 4 tri-wing

• 3 spline, 3 Torq, 3 clutch, wing-nut driver, magnetic bit holder and socket bit holder

• Made of hardened Chrome Vanadium steel for years of dependable use

• Packaged in a handy blow molded case with individually marked bit slots for easy organization

Take one wrench, not two to your next fluid service. The Schwaben Service Wrench fits both crankcase and drain plugs in BMW, Mercedes, and other European vehicles.

Features:

• Six-point 17mm box end won’t round off engine oil drain plugs
• Hardened 14mm hex at the opposite end fits many transmission fill and drain plugs
• Made of vanadium steel with polished chrome finish
• Long handle for added leverage.

Fits most vehicles with M10, M20, M30, M42, M44, M50, M52, M54, M56, M70, S14, S38, S50, S52 and S70.

Application note: Please verify the exact size of the transmission and differential plugs in your car. BMW has used both 14 and 17mm plugs in some vehicles. 

The Schwaben Metric Bubble Flaring Tool Set stands as the ultimate solution for achieving precise brake line connections and flawless tubing applications. This tool set unlocks the ability to craft immaculate ISO bubble flares on brake lines and tubing systems commonly found in European, Japanese, and select domestic model brake lines. The outcome? Connections that are not only secure but also capable of thriving under your vehicle's demanding conditions.

At its core, this set features a robust and enduring hardened steel bar, embodying the essence of durability. Complementing this bar is an extensive array of adapters tailored for 4.75mm, 6mm, 8mm, and 10mm tubing, showcasing the set's versatility across various applications.

Discover unparalleled precision as you secure your brake lines and tubing with the utmost accuracy. This tool set empowers you to effortlessly shape bubble flares, guaranteeing connections that are both leak-proof and resilient. Whether you're a devoted automotive technician or a passionate enthusiast, the Schwaben Metric Bubble Flaring Tool Set is right for you!

Includes:

• Schwaben Metric Bubble Flaring Tool
• Hardened Steel Bar for Enduring Durability
• Adapters for 4.75mm, 6mm, 8mm, and 10mm Tubing