BMW Tools & Specialty Equipment for BMW E12 530i M30 3.0L

Due to clearance issues, many types of lifts require specific adapters that are made for reaching SUV and truck jack points. This 12-piece kit has been made by using stackable adapters that mount inside the lifting block trays so that vehicles with high ground-clearance or those with unique jack point locations are better accommodated. These adapters offer up to 7.2" of additional height when all combined.

Complete kit includes:

• Low‐profile round polyurethane contact pads  -  Qty: 4
• Sliding receivers that accommodate the round polyurethane contact pads and/or the stackable adapters  -  Qty: 4
• 3" stackable adapters.  -  Qty: 4

Fits BL-5000SLX/EXT and BL-7000SLX/EXT Series Only.

• Tough and rigid expanded polystyrene foam (EPS) with a load rating of 1,500lbs per wheel (almost twice what the normal corner weight would be on a 3-series BMW)
• 12" height X 12" width with minimal compression under load
• Light weight with each block weighing less than 6lbs and with a handy strap for carrying or hanging
• Curved cradle for the tire to sit inside
• Non-skid surface that won't scratch your floor

Looking for an alternative to your jack stands? With these wheel blocks you won't have to think twice about a jack stand scratching or denting the underside of your floor or the car falling off the jack stand. These work best when used with a floor jack under the subframe and the opposite axle wheels chocked. These are also a light weight and inexpensive alternative to the super-pricey plastic and metal ramps. They are resistant to most fluids and chemicals (but not solvents) and will never rust unlike metal ramps and blocks.

Also available in a 10" height.

These QuickJack rubber contact blocks are used with all QuickJack systems and can be used with other QuickJack pads or are perfect to replace missing pads.

These blocks are made of a hardened rubber that has specifically been formulated to resist gouging, cutting, and abrasion. They are also resilient against chemicals and solvents that would normally damage rubber.

Dimensions: 4" long x 3" tall x 3" wide

These QuickJack rubber contact blocks are used with all QuickJack systems and can be used with other QuickJack pads or are perfect to replace missing pads. If the blocks included with the QuickJack lift system have a hard time reaching the jack points of the vehicle, these can be used to help properly reach and support the vehicle on the lift.

These blocks are made of a hardened rubber that has specifically been formulated to resist gouging, cutting, and abrasion. They are also resilient against chemicals and solvents that would normally damage rubber.

Dimensions: 4" long x 2" tall x 3" wide

Need an extra lift on your floor jack for your especially tall vehicle?  The FDK2 is here for you.  Brought to you by AC Hydraulic and especially made for their products, this 4.92 inch extension will give you that extra lift you're looking for.

Fits:

• DK40Q
• DK60Q
• DK100Q
• DK120Q
• DK50HLQ

Specifications:

• Height: 4.92"

Engineered for optimal comfort and ease of movement, this reclining creeper seat is ideal for anyone working under vehicles. Its gas spring-supported backrest offers adjustable reclining from 0° to 70°, with seat angles shifting in 10° increments up to 30°, delivering superior ergonomics for mechanics and hobbyists alike.

Equipped with six 360° swivel casters, this creeper seat glides effortlessly around the workspace, allowing you to move smoothly without constantly adjusting your position, helping you stay focused on the job.

Constructed from heavy-duty materials, the seat is upholstered with non-slip, marine-grade vinyl, resistant to abrasion, chemicals, and oil. This durable design provides long-lasting comfort and is the perfect addition to your garage setup.

Features:

• TPR wheels feature a shock absorbing cushioned ride, while providing good floor protection and quiet rolling operation
• TPR wheels are resistant to chemicals, acids, alcohol, and water
• Wide, large diameter wheel improves rolling over rough surfaces
• Heavy-duty non-slip textured marine grade vinyl
• Comfortable thick-padded seat and backrest
• Locking casters
• Seat is resistant to abrasion, chemical, and oil

Specifications:

• Length (Backrest Up): 33 in. / 840 mm
• Length (Backrest Down): 45.25 in. / 1,150 mm
• Width (Frame): 17 in. / 430 mm
• Width Overall: 20.75 in. / 530 mm
• Seat Height (Down): 6.25 in. / 161 mm
• Backrest Height (Up): 31.5 in. / 800 mm
• Seat/Backrest Width: 14.75 in. / 376 mm
• Ground Clearance: ≈3 in. / 76 mm
• Seat Angle Min. / Max.: ≈0° to 30°
• Maximum Load: 600 lbs. / 272 kg.
• Backrest Angle Adjustment: Gas spring
• Seat Angle Adjustment: Mechanical Lock — 3 positions
• Casters: Six 360° Casters, ø2.5 in x .75 in., sleeve bearings, oil resistant, non-marring rubber wheels.
• Seat Materials: Padded Marine Vinyl Backrest and Seat. Marine Vinyl is abrasion, chemical and oil resistant.
• Frame Materials: Full powder coated, welded steel square tube
• Weight: 41.25 lbs. / 19 kg.
• Backrest Angle Min. / Max.: ≈0° to 70°

For some of the best bottle jacks in production, stick with AC Hydraulic.  Now backed by our LIFETIME REPLACEMENT program, don't worry about your jack failing you by combining two amazing brands in one deal: ECS's lifetime replacement and AC Hydraulic's premium quality.

Features:

• 5 models with lifting capacities from 26,500 - 66,000 lb
• With extension screw for optimal use of the stroke
• Jack can be used in horizontal position, as long as the pump piston is placed under the jack
• Fitted with practical carrying handle for easy transport

Specifications:

• Capacity: 26,500 lb
• Min height: 9.06 in
• Hydraulic lift: 6.30 in
• Extension screw: 4.33in
• Max height: 19.69 in
• Bevelled base: Yes