BMW Suspension Parts for BMW 6 Series E24 (1977-1989)

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to address this common issue with Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. These end links feature a bolt-through bushing design, which is compatible with most adjustable aftermarket sway bars. Mounting hardware is included for easy installation.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits most aftermarket sway bars with bolt-through attachment Laser-etched markings for quick and easy adjustments

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to remedy this common issue with a set of Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. A unique knurled bushing design also ensures compatibility with the OEM sway bar, offering a first-to-market solution for enthusiasts looking to retain factory components.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits factory rear sway bars on E23, E24, E28, E30, and E36 Laser-etched markings for quick and easy adjustments

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

These fixed steel camber plates for your E30/E24/E28 will add 3/4 degree of negative camber and will reduce understeer during hard cornering and save the outside edge of your tire. These plates mount to the top of the upper strut bearing and relocate the top of the strut further in. Combine these with the BMW offset upper strut bearings for even more negative camber. These are the perfect camber solution when adjustable plates are not allowed in your class. We used these in our ultra-successful J-Stock suspension as they maximize the available camber in the tire well when using the large, stock-diameter springs.

Instructions for Turner E30 Front Fixed Camber Plates

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is M3

Correct toe settings contribute to both stable steering and even tire wear. The SPC Performance wheel toe bar tool is designed to prevent vehicle drifting and ensure uniform tire wear. It includes a steel bar equipped with sliding adjusters and pointers to accurately assess the vehicle's toe alignment.

For wider wheel bases use T#386442!

Schwaben Shock Nut Socket - 16mm

The Schwaben Shock Nut Socket - 16mm is an essential tool for securely mounting shocks to their mounts. Designed to help achieve the correct torque specification, this socket allows the use of an internal hex wrench to hold the damper shaft in place while using a torque wrench to apply the correct torque. Properly torquing the retaining nut is crucial to prevent premature mount failure or loosening. This high-quality socket ensures a precise fit and reliable performance for maintaining your vehicle's suspension system.

Benefits:

• Allows accurate torquing of shock retaining nuts to prevent mount failure
• Designed for use with an internal hex wrench to secure the damper shaft
• Ensures proper torque application with your torque wrench
• Helps avoid premature mount failure and nut loosening
• High-quality construction for durable and reliable performance
• Compatible with 16mm shock nuts