BMW Engine Parts for BMW 6 Series E24 (1977-1989)

Ignition Distributor Cap contact points can wear and corrode over time leading to misfires and poor engine idling. Replace this with the high quality Bosch unit to restore smooth operation and gas mileage. Replacement for BMW part # 12111715905, 12111725070, and 12111720124.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Fits the following BMW Engines:  M20 M30 S38 M70 M73 S70

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

This is an OEM MAHLE fuel filter that removes dirt and other particle contaminants from your fuel.

A clogged fuel filter makes it difficult for your engine to get all the fueling it needs. Filters commonly clog from a deteriorating gas tank, bad fuel, or other debris in the fuel system. A fresh fuel filter addresses many fuel related problems including surging, stalling, cold start issues, and poor performance under a variety of conditions.

The NOCO GBC003 Boost HD Precision Battery Clamps are heavy-duty clamps crafted for use with 12-volt gas and diesel engines. These clamps feature a needle-nose profile, allowing them to fit any shape or size battery terminal, from small terminals in tight spaces to top and side post batteries, as well as large terminal sizes. Their robust and rugged springs ensure maximum current flow with minimal power loss. Additionally, the Boost HD Precision accessory boasts no-melt and smoke-free properties, high current transferability, and reinforced all-metal construction.

Features: 

• Heavy-duty battery clamp designed for both 12-volt gas and diesel engines.
• Needle-nose clamp profile for jump starting hard-to-reach and oversized battery terminals.
• Made from durable, heat stabilized 8 AWG silicone wire that maintains its flexibility in cold weather environments.
• Engineered to efficiently transfer maximum current flow with minimal power loss.
• Compatible with the GB20, GB40, GB50, and GBX45 UltraSafe Lithium Jump Starters.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.