BMW Suspension Parts for BMW E36 (1992-1998) M3

Sway bars transmit cornering forces from the outside wheels to the inside wheels, helping to keep the vehicle flat during cornering. This, in turn, reduces body roll and improves the driver's cornering confidence. OEM rubber sway bar bushings are designed with comfort in mind, allowing the sway bar to articulate while permitting additional movement, leading to less-than-ideal bar retention and causes unnecessary body roll.

Powerflex polyurethane sway bar bushings are firmer than factory rubber bushings, reducing body roll and keeping sway bars in check. Polyurethane bushings won't slop around like OEM bushings, allowing sway bars to function at their fullest potential.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

This part fits the following BMWs:
 

Swapping in E46 control arms into your E30 or E36 significantly increases negative camber by widening the track width and also gives you more clearance for more steering angle. Condor's CNC machined control arm brackets are made from solid steel and are fitted with a solid hex-shaped bushing. Designed for the street or the track, they hold the control arm steady and eliminate "shimmy" caused by stock bushings. They sharpen steering and improve overall driving feel. Comparable to the NLA Treehouse E36 & E30 Eyeball Arms.

Easiest install of any aftermarket solution
Allow clearance for E30 M50 Conversion exhaust
Street Approved, marginal increase in NVH
Easy Installation, no need for a press
CNC machined steel construction
Solid design without the maintenance of spherical bearings
Heavy-Duty replaceable UHMW insert. Don't be misinformed, UHMW is the best material for these inserts. Delrin is not self-lubricating and will crack and degrade over time.
Powder coated white for corrosion resistance
Improve caster with M3 offset geometry
Keep proper steering geometry under high loads
Made in the U.S.A.
Fitment:
E30 84-91 3 Series
E36 92-98 3 series & Z3

Note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36

Be sure to measure your control arms to determine if you need 21mm or 23mm. Meyle makes a standard e46 control arm and a Heavy Duty control arm. Most HD arms have a hex that is larger in size (23mm). Lifetime Warranty

Subframe mounts are the heart of the rear suspension. Everything is keyed off of these mounts that hold the rear subframe to the chassis. When these start to go bad the entire rear suspension moves. The flex in the bushings can also contribute to rear subframe floor cracks and failures so it's critical to stay on top of the wear and tear on these. Rubber bushings are great for street use but will not hold up to aggressive and track driving. If that kind of driving should have our solid aluminum mounts.

These mounts are the stock E36 M3 subframe mounts and can be used as an upgrade on all non-M E36.

This item fits the following BMWs:
1992-1999 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to address this common issue with Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. These end links feature a bolt-through bushing design, which is compatible with most adjustable aftermarket sway bars. Mounting hardware is included for easy installation.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits most aftermarket sway bars with bolt-through attachment Laser-etched markings for quick and easy adjustments

A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides. 

The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection.

Easily installed with basic hand tools.

*Does not fit convertible chassis"

Fits the following BMW chassis:
E36 BMW All Submodels

Ball-joint failure in the front sway bar / swaybar link on the E36 M3, M Roadster and M Coupe is something that can't be avoided. If you are looking for a direct replacement Lemforder is an OEM supplier to BMW. How do you know if the link has gone bad? From inside the car you will hear a clunking noise when going over bumps. The clunk is a sure sign a ball joint (control arm, tie rod, swaybar link) has failed. Diagnosis with a set of channel-lock pliers will reveal a large amount of play in the ball joint itself.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1995-1998 E36 BMW M3
1996-2002 Z3 BMW M Roadster M Coupe

NOW LOCATED UNDER T#339018

KONl Sport struts and shocks are the industry leader for user adjustable damping for daily drivers to weekend warriors. KONl Sport's familiar yellow color has for decades meant superior motion control and adjustability for the discerning driving enthusiast.

• Big handling improvements
• Reasonable ride quality
• Re-buildable for custom vehicle setups
• Best KONl shock for all lowering springs
• Lifetime Warranty

Activate your Koni Rebate!

This part fits the following BMWs:

E36 M3

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to remedy this common issue with a set of Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. A unique knurled bushing design also ensures compatibility with the OEM sway bar, offering a first-to-market solution for enthusiasts looking to retain factory components.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits factory rear sway bars on E23, E24, E28, E30, and E36 Laser-etched markings for quick and easy adjustments

TMS E36 solid sub-frame bushings are designed for track and racecars to remove twisting and flexing of the subframe where it mounts to the rear floor. This twisting is one of the causes of rear subframe/floor failure in E36 cars. We originally developed these for our SCCA SPEED World Challenge cars. A BMW's subframe is the heart of the suspension. Because the subframe is mounted with rubber isolators, when the subframe moves, so does the rest of the suspension mounting points. As the rubber wears and becomes more pliable, the alignment and suspension settings move even more. Replace the stock rubber bushings to limit drivetrain and suspension movement and keep your car set up the way it's supposed to be.

Our mounts are designed using a CAD program with further attention paid to making the mount as light as possible. We also notched the flanges to allow the use of the BMW factory removal tools. One front bushing is slotted to allow for compliance between manufacturing standards as BMW specifies. These bushings are CNC machined out of high grade billet aluminum.

Click for installation instructions. (PDF)

KONl Sport struts and shocks are the industry leader for user adjustable damping for daily drivers to weekend warriors. KONl Sport's familiar yellow color has for decades meant superior motion control and adjustability for the discerning driving enthusiast.

• Big handling improvements
• Reasonable ride quality
• Re-buildable for custom vehicle setups
• Best KONl shock for all lowering springs
• Lifetime Warranty

Activate your Koni Rebate!

This part fits the following BMWs:

E36 M3, Z3MM3, Z3M

Sway bars transmit cornering forces from the outside wheels to the inside wheels, helping to keep the vehicle flat during cornering. This, in turn, reduces body roll and improves the driver's cornering confidence. OEM rubber sway bar bushings are designed with comfort in mind, allowing the sway bar to articulate while permitting additional movement, leading to less-than-ideal bar retention and causes unnecessary body roll.

Powerflex polyurethane sway bar bushings are firmer than factory rubber bushings, reducing body roll and keeping sway bars in check. Polyurethane bushings won't slop around like OEM bushings, allowing sway bars to function at their fullest potential.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

This part fits the following BMWs:
1992-1999 E36 318i 318is 318ti 320i 323i 325i 325is 328i 328is M3

Tasked with keeping the vehicles rear end firmly mounted while absorbing noise, vibration, and harshness (NVH) factory rubber subframe bushings were engineered to provide a balance of control while keeping the ride quality soft and supple. As a factory bushings age, they become brittle and begin to harden. When this happens the bushing will actually shrink and allow excess play, or movement in the subframe. This is typically felt by a sudden jerk or "thunking" noise under acceleration and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushings with full polyurethane this play is eliminated since the subframe is being held in place by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering and acceleration inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver. 

Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

This part fits the following BMWs:
1992-1999 E36 318i 318is 318ti 320i 323i 325i 325is 328i 328is M3