Lightweight flywheels have proven themselves to be a worthwhile performance enhancement. But with the quicker throttle response and horsepower improvement comes one serious drawback: flywheel chatter. Without the dual-mass flywheel's rubber isolators, a lightweight aluminum flywheel has more rattle than stock. ECS has designed this flywheel using chrom-moly steel and it weighs almost ten pounds less than the stock DMF but not as extreme as full aluminum flywheels. The steel helps dampen vibration and noise so you get near-factory refinement and most of the benefits of a lightweight flywheel: quicker throttle response, better reliability, and more power to the wheels. Zero-balanced and SFI 1.1 certified (material and design has been independently burst tested to ensure quality and safety). This flywheel requires the E34 M5 sprung hub clutch kit. Choose below from the flywheel only or a complete kit.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

Stock flywheel weight - 25.0lbs
ECS flywheel weight = 16.55lbs

This item fits the following BMWs:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i (5-speed) 

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left- and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 175mm (6.89") to 235mm (9.25") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints (M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability NOTE: If you've modified your vehicle's suspension with aftermarket struts or coilovers, the mounting location for the sway bar end link may have moved. To confirm fitment with our adjustable end links, please measure the distance between the sway bar and the mounting location on the strut body with the vehicle at ride height and confirm that it is within the 175 - 235mm range of adjustment.

Elevate Your BMW's Performance with ECS Tuning's Ultimate Performance Rear Shock Mount Kit

ECS Tuning presents the Ultimate Performance Rear Shock Mount Kit, specifically designed to address recurring rear shock mount blowouts experienced by various BMW models, including the M3 and non-M 3 Series dating back to the E30 chassis in 1984. This innovative kit provides a long-term solution, ensuring optimal damper performance and longevity while eliminating rear clunking noises and handling issues caused by blown shock mounts.

Key Benefits:

• Solves rear shock mount blowout issues on BMW models
• Allows full articulation of rear dampers for improved performance
• Industry-first design with PTFE lined stainless steel monoball spherical bearing
• 80A polyurethane isolation bushings reduce noise, vibration, and harshness (NVH)
• Lower dust seal enhances bearing life by preventing road debris ingress
• Corrosion-resistant anodized 6061-T6 construction for durability
• Compatible with 10mm, 12mm, or 14mm damper shafts

Upgrade your BMW's rear shock mounts with ECS Tuning's Ultimate Performance Rear Shock Mount Kit, providing superior performance, reduced NVH, and increased bearing longevity for a more controlled and comfortable ride.

Upgrade the cooling system of your BMW with the BMW E36 High Performance Aluminum Radiator with Silicone Radiator Hoses Kit. This high-quality radiator kit is designed specifically for BMW E36 models, providing improved cooling efficiency and durability. Paired with silicone radiator hoses, this kit offers superior heat resistance and reliability, making it ideal for high-performance applications. Enhance the cooling performance and reliability of your BMW with this premium radiator kit.

• Improved cooling efficiency for better engine performance
• Durable aluminum construction for long-lasting use
• Silicone radiator hoses offer superior heat resistance
• Designed specifically for BMW E36 models

Black Chrome UNIVERSAL Swivel Exhaust Tip - 4.0" offers both style and adjustability with its innovative design. This exhaust tip features a unique swivel collar that allows for precise alignment and perfect fitment. The tip can be adjusted to any direction, and once set, it remains securely in place by tightening the hex bolt to 14 ft-lbs (19 Nm).

• Precision Laser Etched Logo: Each tip includes a laser-etched logo for a premium look.
• Durable Construction: Built with chrome-plated nuts, a 304SS cap screw, clamp, insert ring, and exhaust tip for longevity.
• Stylish Design: Features a slant cut, double-wall construction, and rolled edge for a striking appearance.
• Versatile Fitment: Available in a 4.0" outlet and finished in a sleek black chrome.
• Dimensions:
  • Inlet Size: 3.0"
  • Overall Length: 7.0" (6.0" Tip + 1.0" Clamping Surface)
  • Outlet Size: 4.0"
  • Outlet Style: Double Wall, Rolled Edge, Slant Cut

Modification may be required for proper fitment.

BMW E3X Wheel Stud Conversion Kit - Half set

Enhance your BMW E3X's performance and safety with the BMW E3X Wheel Stud Conversion Kit - Half set. This kit allows for easy conversion from lug bolts to wheel studs, providing a more secure wheel mounting solution. Engineered for durability and reliability, it ensures optimal wheel alignment and reduces the risk of stud breakage. Upgrade your BMW E3X with this premium wheel stud conversion kit today.

• Easy conversion from lug bolts to wheel studs
• Provides a more secure wheel mounting solution
• Ensures optimal wheel alignment
• Reduces the risk of stud breakage for improved safety

Want a race-spec rear shock mount but with the comfort of a factory bushing? This ECS rear shock mount combines the precision and articulation of a spherical bearing with the isolation of urethane bushings. The stainless monoball bearing is lined with PTFE lubricant and suspended in 80A urethane and housed in a hard anodized 6061-T6 aluminum mount. The spherical bearing is a better design than most rear shock mounts because it allows the shock to move and tilt without side-loading the shock shaft (which leads to premature failure of the shock). Most Genuine BMW and aftermarket shock mounts are not designed for shock angles and the stress that track or performance driving will put on the shock shaft. The ECS shock mount is properly designed to handle these loads. The internal bearing is also replaceable - it will be years before you have to replace the entire mount. The ECS mount is fully encapsulated to prevent the common shock mount failure of the stock mount design.

ECS RSM features:

• Maintenance free, PTFE lined, stainless steel monoball spherical bearing for full shaft articulation
• 80A polyurethane isolation bushings for NVH control
• Accommodates 10mm, 12mm, or 14mm damper shafts
• Fully constrained shaft mount makes RSM blow out impossible
• Hard anodized 6061-T6 construction
• Fully rebuildable design

* - the RSM comes with the BMW standard 10mm shock shaft bushings. 12mm is used on some performance shocks and 14mm is used on some true motorsport rear shocks.

The ECS BMW Coilover line was designed with daily drivers in mind! The focus was to improve on the performance and look of the suspension, without forgoing any comfort. Like many of the top-tier coilovers, these coilovers feel as smooth and comfortable as a stock setup, while giving you an aggressive look and vastly improved handling, all at a fraction of the price!

The ECS Tuning Performance Coilover System provides a sport-tuned, height, damping, and body adjustable suspension with substantial performance benefits using high-quality materials and coatings to replace your worn suspension, all while giving your vehicle that perfect ride height!

Spring Rates: Front is 6 kg/mm, Rear is 8 kg/mm

PERFORMANCE FEATURES

32 levels of rebound damping adjustment Adjustable damping, monotube shocks/struts paired with optimized progressive rate coil springs gives your vehicle road-sticking grip with reduced body roll for exceptional confidence in your vehicle's handling. With your vehicle's new, lower ride height the center of gravity is now moved lower, further improving handling performance Adjustable front bodies allow you to set the ride height while maintaining correct spring pre-load Adjustable front and rear bodies allow the shock to operate in the correct valving range, regardless of ride height PRODUCT DESIGN

Strut and shock bodies finished with a durable gloss black powder coat for good looks and great longevity Threaded portions are are clear zinc coated for optimum corrosion protection against rain and salt Coil springs are powder-coated Reflex Silver Metallic finish for durability Red anodized, billet aluminum lower spring seats with locking collars allow for quick, on the car, adjustability with the included spanner wrenches Integrated bump stops KIT CONTENTS

ECS Performance Adjustable Coilover System - E36 (Non-M) Front Coilover Installation Hardware: Self-Locking Hex Nut for Front Sway Bar Bracket - 07129964672 (2) Washer for Front Sway Bar Bracket - 31111114348 (2) Through-Bolt for Lower Strut Mounting - 07119900587 (2) Washer for Lower Strut Mounting - 07119904119 (2) Self-Locking Hex Nut for Lower Strut Mounting - 07119905753 (2) Hex Bolt with Washer for Lower Strut Mounting - 31311136465 (4) Front Strut Mount Gasket - 31331094288 (2) Front Strut Mount Reinforcement Plate - 31312489795 (2) Rear Coilover Installation Hardware: Rear Shock to Trailing Arm Bolt - 07119900402 (2) Rear Shock Mount Gasket - 33526772864 (2) ECS HD Rear Shock Mount Reinforcement Plates - 002478ECS01KT Rear Lowering Spring Pad - 33531135420 (2) Rear Upper Spring Pad - 7.5mm - 33531136386 (2)

Drastically improve the looks of your vehicle while improving your vehicle's handling characteristics and/or easily adjust your wheel fitment to allow for the proper clearance when installing parts such as new wheels, big brake kits, or lowering suspension components.Interference from components such as shocks, springs, or control arms are a common issue when installing wheel that are not a direct OE size replacement. By moving your wheels a few millimeters each, you can give yourself enough clearance for proper wheel fitment and give your car a wider stance in the process.

ECS Tuning wheel spacers are constructed of high quality 6061-T6 aircraft grade aluminum and are specifically designed by in-house engineers and cnc machined to exact standards, ensuring the best fitment possible. By carefully measuring the OEM wheel hubs and bore dimensions, these spacers mount with minimal clearance to prevent any vibration, retaining the stock-like vibration free operation. 

ECS Tuning is a performance and genuine parts provider that designs their ECS Tuning branded aftermarket automotive parts in-house to ensure the highest quality and affordability possible. Every part's design is subjected to a rigorous test fit and stress test period to guarantee proper fitment and continued reliability for years to come.

This item fits the following BMWs:

2008-2012 E82 BMW 128i 135 1M
1988-1991 E30 BMW M3
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2012 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2012 E93 BMW 328i 335i M3 - Convertible
1976-1981 E12 BMW 528i 530i
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 530i 535i 540i M5
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i M5
1982-1989 E24 BMW 633csi 635csi M6
2004-2010 E63 BMW 645ci 650i M6
1981-1987 E23 BMW 733i 735i
1988-1994 E32 BMW 735i 735il 740i 740il 750il
1995-2001 E38 BMW 740i 740il 750il
1990-1999 E31 BMW 840i 840ci 850i 850ci 850csi
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
2009-2016 Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

Rear Only
2007-2013 E70 BMW X5M
2007-2014 E71 BMW X6 xDrive35i X6 xDrive50i X6M

Enhance Your BMW's Aesthetic with ECS UNIVERSAL Exhaust Tips - 4.0" Titanium - Burnt Finish - Pair

• Elevates the look of your BMW's exhaust system
• Constructed from high-quality titanium for durability
• Features a stylish burnt finish for a unique appearance
• Easy to install and compatible with most exhaust systems

Upgrade the appearance of your BMW's exhaust system with the ECS UNIVERSAL Exhaust Tips - 4.0" Titanium - Burnt Finish - Pair. Crafted from high-quality titanium, these exhaust tips are not only durable but also add a touch of sophistication to your vehicle. The burnt finish enhances the overall aesthetics, giving your BMW a unique and eye-catching look. Installation is a breeze, and these tips are designed to be compatible with most exhaust systems, ensuring a seamless upgrade experience.

Upgrade the wheel setup of your BMW with the BMW Wheel Stud Conversion Kit - Half set. This high-quality conversion kit allows you to replace your existing wheel bolts with wheel studs, providing easier wheel installation and improved stability. Engineered specifically for BMW models, this kit includes everything you need for a half-set conversion. Enhance the performance and convenience of your BMW with this premium wheel stud conversion kit.

• Easier wheel installation compared to traditional bolts
• Improved stability and safety with wheel studs
• Engineered specifically for BMW models
• Includes everything needed for a half-set conversion