BMW Drivetrain Parts for BMW 5 Series E39 (1996-2003)

Sometimes choosing the correct shift kit proves difficult when you dual-purpose your favorite vehicle, we understand this well. The early days for any race enthusiast usually begins with a car that is needed to daily drive and setup to get out on the track. What becomes difficult is properly modifying that car to feel comfortable in both situations which is why we took this view on our new short shift line. This upgraded lever is a quick swap option to replace the standard shift lever that come with our kits so you can keep your hands closer to the wheel while shifting at high speeds. Designed from anodized aluminum this lever looks great in any interior for the daily driver who simply prefers the taller lever look and feel.

NOTE THAT THESE ARE DESIGNED TO WORK WITH TURNER MOTORSPORT SHORT SHIFTERS ONLY - We wanted to give you the option to buy one separately, in case you changed your mind after buying our short shifter.

Features:

Compatible with stock shift boot fits nicely into the machined groove at the bottom of the lever to maintain a clean look in the interior.
Machined from 6061-T6 aluminum and type II anodized for exceptional durability and corrosion resistance.
Available in either black or clear anodize to match your vehicle’s interior.
Rally shift knob is machined from black delrin.
Unlike aluminum, delrin will not hold heat so on those hot days you won’t have to worry about burning your hand on a knob that’s been baking in the sun.
Shift knob is threaded onto the end of the shift lever utilizing a standard ⅜-16 thread to allow for easy removal and attachment of your favorite beer tap or other accessory.
“Quick Change” height adjustable upper shift lever design allows for quick swapping between optional “OE” style and “Rally Style” upper shift levers.
22mm adjustment range to fine tune shifter throw and feel.

If allowed in the rules these solid aluminum transmission mounts offer many advantages over a urethane or Delrin mounts. It's no wonder that these mounts have found their way into the top BMW racers in the country. These are machined from solid aluminum and have zero deflection, engine torque will cause a rubber or urethane mount to flex or deflect allowing more torque to passed through the drive line (instead of being wasted winding up the mount). This puts the shift linkages in better consistent alignment. And unlike rubber or urethane the aluminum has zero wear and is not affected by leaking oil or other fluids so this is likely the last set of transmission mounts you will ever need. We very strongly recommend using the solid transmission and engine mounts together as a complete kit, mixing a rubber mount with a metal mount will cause undue stress on the mounting points and will lead to a failure. We never advise using a solid mount unless a corresponding solid mount is also used.

These are a no-compromise design for all-out racing use, full solid aluminum mounts should not be used on street-driven cars since there is no material to absorb vibration making these quite harsh for regular street use (track cars don't care about noise).

Product features and benefits:

• Crisper throttle response, positive shifter location, direct power transfer
• Precision machined billet 6061-T6 aluminum housing
• Grade 10.9 stud - fear not, big turbo owners
• Engineered in-house and made in America

This item fits the following BMWs: 
1989-1995  E34 BMW  525i 530i 535i 540i M5 
1992-1998  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 
1997-2003  E39 BMW  525i 528i 530i 540i M5 
1999-2005  E46 BMW  323i 323ci 325i 325ci 328i 328ci 330i 330ci M3 
2008-2012  E82 BMW  128i 135i 1M Coupe 
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan 
2006-2012  E91 BMW  328i - Wagon 
2007-2013  E92 BMW  328i 335i 335is - Coupe 
2007-2013  E93 BMW  328i 335i - Convertible 
1997-2002  Z3 BMW  Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe ​

Enhance your car's performance with ECS Tuning's polyurethane transmission mounts, designed for both street and track applications. These mounts are engineered to withstand high torque and forced-induction scenarios, eliminating concerns about torn mounts and providing a more engaging driving experience. Although polyurethane may introduce some additional NVH (Noise, Vibration, Harshness), its exceptional durability, wear resistance, and resistance to water, oil, and grease make it the perfect choice for performance enthusiasts. ECS Tuning offers two durometer options to match your driving style, along with a comprehensive DIY installation guide, ensuring a complete solution for your transmission mount requirements.

Key Features:

• Minimized transmission movement, reducing the risk of mis-shifts and over-revs.
• Made from high-quality polyurethane bonded with 304 Stainless Steel.
• Enhanced driving experience for both street and track enthusiasts.
• Two durometer options available: 80A for race applications and 70A for daily driving (ES#2859359).
• Replaces weak OEM mounts.

A common source of leaks, the selector shaft seal should be replaced whenever the shifter assembly is serviced to prevent fluid loss.

Fits the following BMW chassis:
E36, E39, E46, E36/7 Z3

Most flywheel bolts are single-use only. They stretch when tightened. New mounting bolts are required with any flywheel swap. This is a set of 8 OE BMW M12x1.5x50mm flywheel bolts to help complete the job.

Replaces BMW #11221730533.

Requires shorter flywheel bolts - 8x (P# 11227805885) - T#12322

Lightweight flywheels have proven themselves to be a worthwhile performance enhancement. But with the quicker throttle response and horsepower improvement comes one serious drawback: flywheel chatter. Without the dual-mass flywheel's rubber isolators, a lightweight aluminum flywheel has more rattle than stock. ECS has designed this flywheel using chrom-moly steel and it weighs almost ten pounds less than the stock DMF but not as extreme as full aluminum flywheels. The steel helps dampen vibration and noise so you get near-factory refinement and most of the benefits of a lightweight flywheel: quicker throttle response, better reliability, and more power to the wheels. This flywheel requires the E34 M5 sprung hub clutch kit.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

Stock flywheel weight - 25.0lbs
ECS flywheel weight = 16.55lbs

This item fits the following BMWs:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i (5-speed)

Ensure the longevity of your BMW's drivetrain with ECS Tuning's Magnetic Plugs. These plugs are meticulously engineered in-house to provide a perfect fit and feature a permanent magnet attached to the plug body. The magnet effectively attracts and captures tiny abrasive and ferrous metal particles, preventing their circulation through lubrication systems. Metal particles can accumulate due to various conditions such as normal wear, machining operations, casting flaws, and stress usage, leading to excessive wear of vital components. ECS Tuning's Magnetic Plugs help alleviate this concern by trapping these particles, thus safeguarding the internal components of your drivetrain. With a convenient 17mm hex head design, these plugs eliminate the need for special tools required for OEM plugs.

Key Benefits:

• Removes abrasive metal particles from drivetrain fluid
• Prevents excessive wear to internal components
• Meticulously engineered for a perfect fit
• Features a permanent magnet for efficient particle capture
• Convenient 17mm hex head design for easy installation

Ensure smooth clutch operation in your BMW with the Turner Motorsport Genuine BMW Clutch Release/Throw-out Bearing. This crucial component, situated between the clutch pressure plate and release fork lever, is essential for optimal performance. When renewing your clutch, don't overlook the importance of replacing this genuine BMW bearing.

Key Benefits:

• Genuine BMW quality guarantees a perfect fit.
• Prevents clutch-related issues for reliable performance.

Upgrade your BMW's clutch system with the Turner Motorsport Genuine BMW Clutch Release/Throw-out Bearing.

This is the shifter actuator pin that's part of BMW's gate system for the shifter.

Genuine BMW Locking Pin
This item fits the following BMW Chassis:
E36 M3,E34,E36,E39,E46,E53 X5
 

Elevate your BMW's maintenance routine with this specialized butyl tape tailored for the center support bearing. Usually replaced during servicing, this butyl tape plays a crucial role in providing proper sealing and support for your BMW's center support bearing, contributing to enhanced performance and extended longevity.

Key Benefits:

• Specifically designed for BMW center support bearing maintenance
• Ensures proper sealing and support
• High-quality tape for reliability and durability