• 70MM, 80MM, OR 90MM OVERALL LENGTH
• OUR HIGHEST-GRADE PREMIUM WHEEL STUD
• DRY LUBE WITH BLACK M-PHOSPHATE COATING
• STUD FOR RACE/TRACK USE
• CORRECT SHOULDER SIZE FOR A WIDE RANGE OF HUBS/BRAKE ROTORS
• USE WITH 14x1.5 NUT
  
• For the very best in a race-grade wheel stud, stop looking! These are the wheel studs that our race teams insist on (after years of trying every stud design on the market). MSI Racing specializes in hardware for motorsport use (NASCAR and IMSA) and other advanced industries. We tried them on our Grand-Am/IMSA racecars and were very impressed by the performance and durability of their designs. Race wins and championships can come down to the seconds of a pitstop. We could run any wheel stud in the world and we use these. After testing them over the course of a few endurance seasons we decided to offer them to all of our customers as well.
  
  These studs are available in three overall lengths - 70.5mm, 80.5mm, and 90.5mm. All sizes are made with aircraft quality alloy steel and have roll formed threads for greater strength than cut threads. We use a dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish. Manganese is preferred over the more common zinc because it's better at reducing friction and wear to prevent thread galling. With the dry lube applied over the phosphate this is the best corrosion resistance we have seen in any wheel stud! Salt tests have shown this stud is superior to others in corrosion resistance. The dry lube helps the nut engage and glide over the threads for faster engagement without cross threading or binding. Other features of our MSI studs include a large bullet nose nut-starter and a properly sized shank to work with a wider range of BMW wheel, nut, and brake rotor combinations. We intentionally avoid the extra large shoulders you see on other studs because they can interfere with some brake rotor hats. The extra large shoulder can be too large to allow the rotor to pass through and drilling out the holes is required (not cool!) Our studs have the sufficient shank for the brake rotor without interfering.
  
  We configured these studs to have a 14x1.25 thread to go into the wheel hub. But the exposed stud has 14x1.5 threads. We did this because threading a nut is faster on 1.5 threads than a finer 1.25 thread pitch, which saved us time during pitstops. There are also more wheel nut options in 14x1.5. When you order our 14x1.25 studs make sure you also order the 14x1.5 nuts.
   

  FREE red threadlocker with purchase of a full set of wheel studs (16 or more)MSI Dry Lube Bullet Nose Wheel Stud Features:
  

• Dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish
• Innovative nut-starter and bullet shape radius that all but eliminates cross-threading
• Properly sized shank to work with a wide range of brake rotor, wheel, and nut combinations
• Heat-treated aircraft quality alloy steel
• Developed from over 20 years of top level NASCAR use
  
• These studs are installed using the traditional 'double-nut' method (one regular nut and one jam nut) with thread locking compound (Red Turbo-Lock or similar).
  
  Sold per stud.
  Wheel nuts sold separately.

Elevate your BMW's performance and reduce rotational mass with ECS Titanium Wheel Bolts, ideal for weight-conscious enthusiasts or those seeking high-quality, rust-resistant wheel bolts.

Key Benefits:

• 50% lighter than steel bolts, reducing rotational mass for improved performance.
• CNC'd from annealed titanium alloy, ensuring high quality and durability.
• Tested to class 10.9 fastener proof load requirements without signs of fatigue.
• 14mm diameter, 1.25mm thread pitch, 27mm length, conical seat, and 17mm head.
• Thoroughly clean hub threads before installation to prevent fatigue or cracking.
• Note: Adjust bolt length when using wheel spacers for proper fitment.

Upgrade to ECS Titanium Wheel Bolts for your BMW, optimizing performance while maintaining high quality and durability.

ECS Tuning lab tests its fasteners to ensure they meet all 10.9 specifications.

Wheel Bolt specs:

• Diameter - 14mm
• Thread Pitch - 1.25mm
• Length - 33mm

If installing wheel spacers, measure your current wheel bolt's length and add the width of your spacer to determine correct extended bolt length. 

Used on a wide variety of both BMW and MINI wheels. Best to replace whenever new tires are being installed.

Genuine BMW Rubber Valve - L=42,5Mm
This item fits the following BMW Chassis:
E30 M3,E36 M3,E34 M5,E60 M5,E63 M6,E46 M3,E70 X5M,E71 X6M,E82 1M Coupe,E85 Z4M,E53 48IS,E30,E34,E36,E38,E39,E46,E53 X5,E63,E65,E70 X5,E71 X6,E82,E83 X3,E85 Z4,E86 Z4,E89 Z4,E90,E92,E93,F01,F02,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4 X4,F30,F31,F32,F33,F34,F36,F80 M3,F82 M4,F83,i3i12
 

APR Black Valve Stem Caps are a stylish and functional upgrade for your vehicle's wheels. Sold as a set of four, these high-quality aluminum caps feature an engraved APR logo on each cap. Designed to add a touch of customization to your vehicle, they also serve a practical purpose.

• Premium Quality: Made from durable aluminum for long-lasting performance.
• Enhanced Aesthetics: Features an engraved APR logo for a sleek and stylish look.
• Functional Design: Helps protect valve stems from dirt and moisture.
• Easy Installation: Simple to install and compatible with most standard valve stems.

Upgrade your vehicle with APR Black Valve Stem Caps to enhance both style and functionality.

ECS Tuning lab tests its fasteners to ensure they meet all 10.9 specifications.

Wheel Bolt specs:

• Diameter - 14mm
• Thread Pitch - 1.25mm
• Length - 27mm

If installing wheel spacers, measure your current wheel bolt's length and add the width of your spacer to determine correct extended bolt length. 

The engineering team at ECS Tuning have now made it possible to easily bolt on modern day 5x127 (5x5) Jeep wheels (71.5mm CB) onto your BMW. This vastly opens up the options for popular off-road wheel styles to choose from, or you can buy an inexpensive set of OEM Jeep wheels to bolt on to your European car or SUV.

PART DESIGN

In-house designed and engineered using FARO ARM laser scanning technology and SolidWorks 3D CAD modeling for precision fitment

Designed to fit modern day OEM and aftermarket Jeep wheels using 5x127 (5x5) bolt circle and 71.5mm center bore

Precision engineered to fit the OEM BMW 74.1mm hubs to maintain vibration-free operation

CNC-machined from a solid block of 6061-T6 billet aluminum then black anodized for corrosion protection

Includes pre-installed press-fit M14x1.5mm RH thread wheel studs along with 60° conical seat, open-ended chrome lug nuts for the proper Jeep lug seat

KIT CONTENTS

5x120mm (74.1mm CB) to 5x127mm Wheel Adapters - QTY 4

M14x1.5mm conical seat lug nuts - QTY 20