BMW Engine Parts for BMW X Series E71 (2008-2014)

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Enhance your BMW's performance with the upgraded BAV Ignition Coil, designed to boost firepower and optimize engine efficiency. These coils boast modified core windings for a faster, more efficient burn, resulting in increased torque at lower RPMs and heightened horsepower in the upper range. While improvements depend on your engine's condition, these coils ensure noticeable enhancements in performance and potential fuel economy benefits.

Product Benefits:

Improved engine firepower and efficiency
Increased torque at lower RPMs
Enhanced horsepower in higher ranges
Potential improvement in fuel economy
Set of six for complete BMW Cooper replacement

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

For BMW M54 applications, coil styles vary between M or N depending on the vehicle's production date. Models produced up to September 2002 require the M series style coil, while those manufactured after September 2002 use N series style coils. It's crucial to visually compare and verify the correct coil needed for your vehicle before making a purchase.

Benefits:

• Specific coil styles for different BMW M54 application dates
• Helps ensure the right replacement part for your vehicle's coil
• Visual verification recommended prior to purchase for compatibility

BMW Gray Filter Housing Cap - Blackline Performance Edition Oil is a premium upgrade designed to replace the standard OEM plastic oil filter housing cap. This high-quality billet aluminum cap enhances both the aesthetics and functionality of your BMW's engine.

• Durable Construction: Made from 6061 T6 aluminum with a hard anodized finish for superior strength and longevity.
• Improved Performance: Features better heat dissipation compared to the factory plastic cap, enhancing engine performance and reliability.
• Enhanced Aesthetics: Adds a sleek, high-performance look to your engine bay with 3D precision post-milled detailing and the G Insignia Oil Filter Cage Stabilizer.
• Easy Installation: CNC-formed hand grips and a 10mm Allen key maintenance port with a built-in scratch plate simplify the installation and maintenance process.
• Direct Replacement: Retains the factory oil filter stalk and is compatible with BMW S55 and most N series engines using BMW part 11427525334.
• Increased Longevity: Designed to increase the life span of your oil filter cap and provide a more reliable seal.