BMW 1 Series E82 (2008-2013)

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Every 60-80,000 miles, we recommend replacing your spark plugs to ensure your ignition system is running optimally. Over time carbon can build up around the head of the spark plug and decrease spark strength and effectiveness, leading to weaker fuel mixture detonation, misfires, and potential check engine lights. To prevent this, have put together our High-Performance Ignition Service Kits. These kits include new Bav Auto High-Performance Ignition Coils, new spark plugs, dielectric grease, and a BMW spark plug service label to keep track of when your spark plugs were replaced.

Bav Auto's Ignition coils feature core windings that have been modified to increase firepower and promote a faster, more efficient burn. This gives your BMW/MINI increased torque in the lower range of RPM and more horsepower in the upper range. Exact improvements depend on the current condition of your engine, but you'll definitely feel the difference. They'll also improve your fuel economy.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

The DCT transmission in your BMW is nothing short of incredible and exhilarating, but also astronomically expensive to replace. BMW has been labeling fluids as "lifetime" for quite some time now, and as enthusiasts and owners have learned over the years, there simply is no fluid that last a lifetime.

This DCT service kit that takes the guesswork out of a fluid change . No need to track down the correct fluid and plugs, simply open the box, and get the job done the correct way. By servicing your DCT transmission, you will be assured that old, broken down fluid won't cause a several thousand dollar nightmare. We recommend this service every 40,000 miles to keep your transmission going strong for years to come.

Kit includes:

• 5 quarts of Pentosin DCTF-1 fluid
• DCT transmission cartridge and suction filters
• Drain and fill plugs

Please note: We include 5 quarts of DCT fluid because without a GT1 diagnostic tool and much more involved labor, you will not be able to replace over 5 quarts of fluid. Many elect to do this service and simply flush the fluid 5,000 miles later to ensure all fluid has been flushed, but this is not mandatory.

Both the cartridge and suction filters have their own challenges in replacing. For best results, replace both.

This is an OEM INA mechanical tensioner for the serpentine belt. This tensioner keeps the belt for the alternator, power steering and Air Conditioning taught to provide maximum performance of each system.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

The fuel pump is held into the tank with a retaining lock ring. Most people would take an extension or punch and tap out the ring with a hammer. But that's the wrong way to do it. You could damage the lock ring, or worse, the tank itself. This handy tool is toothed to match the lock ring and takes a standard 1/2 drive ratchet or small extension. Twist the ratchet and the lock ring comes un-done cleanly and smoothly. A hefty tool that pays for itself over and over. Fits most BMWs from 1988-2013. Also has application for MINI and Porsche.

This metal screw ring tightens down to old the top of the fuel pump or fuel filter assembly dependent on model of vehicle.

Together they make this job simple and easy and ensure a tight fit with a new ring. 

A lightweight aluminum flywheel is a great way to increase throttle response and free up horsepower by reducing drivetrain loss. Factory flywheels are built to minimize engine and transmission vibrations, making them heavier and requiring more energy to make them spin. An aluminum flywheel can save lots of weight over the stock steel unit - sometimes over 50%. While the dampening effect of the stock flywheel is reduced, most enthusiasts would agree that the increase in performance is well worth it. In addition, the lighter flywheel allows the engine to spin more freely, improving throttle response.

This JB Racing lightweight aluminum flywheel kit and is designed to be used with the included factory clutch, making replacement and service easy and inexpensive, especially compared to specialized racing clutches. It also preserves the driveability of your car on the street, and enthusiasts tolerant of a mild to moderate NVH increase will be especially taken with this setup. In addition, the JB Racing flywheel can be easily rebuilt with a new clutch contact surface, allowing you to enjoy faster revs and superior response for many years to come.

Stock Flywheel Weight: 24-31 lbs.

JB Racing Lightweight Aluminum Flywheel: 12 lbs.

This item fits the following BMW Chassis:
E61/1, E82/88, E9x, Z4

Fits the follow engines:
N52 3.0L

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

Turner Motorsport Direct Replacement Center Grilles for BMW

Upgrade your BMW's front end with Turner Motorsport's Direct Replacement Center Grilles. This kit replaces the stock chrome kidney/center grilles, delivering a bold and aggressive appearance. Included are two black grills and two hood trims for a comprehensive transformation.

Key Benefits:

• Direct replacement for stock chrome grilles
• Aggressive aesthetic enhancement
• Made from impact-resistant, long-life ABS polymer
• Precision-crafted for a perfect OEM fit
• High-quality matte finish resembling genuine BMW parts

Crafted from durable ABS polymer, these black grilles not only provide impact resistance but also ensure a long-lasting upgrade. The precision engineering guarantees an OEM fit, while the high-quality matte finish perfectly complements the authentic BMW look.

Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication! 

Liqui Moly GmbH develops and tests all engine oils, additives, and car care products in-house, ensuring all Liqui Moly products extend the life of your engine via optimal lubrication. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world. Turner Motorsport trusts Liqui Moly to keep all of our race cars - including the M6 - running smooth from the first hotlap to the last.

Turner Motorsport Recommends three Liqui Moly oil options for your BMW:

Leichtlauf High Tech full synthetic engine oil is designed to provide the highest amount of engine protection as well as fuel savings and reduced oil consumption - most BMWs like to drink oil, Leichtlauf should make yours less thirsty. Using proprietary blends of base oils and the latest additive technology, this oil will ensure smooth running gasoline and diesel engines in both high and low temperatures. Other amazing benefits include: optimum oil pressure at all speeds, rapid oil delivery at low oil temperatures, high shear and aging stability, turbo, multi-valve, and supercharger compatibility, and long service life.

Synthoil Premium engine oil is designed to provide great engine wear protection as well as fuel savings and reduced oil consumption. Using proprietary blends of base oils and the latest additive technology, this full synthetic oil will ensure smooth running gasoline and diesel engines in both high and low temperatures.

New generation Molygen engine oil allows you to easily identify oil leaks with the included UV flashlight - BMWs are notorious for oil leaks, and this allows you to work towards solving this problem. Additionally, Molygen is a fully synthetic oil designed to provide the highest amount of engine protection as well as fuel savings and reduced oil consumption possible. 

Choose the level of Liqui Moly Oil Service your BMW deserves: 

• Liqui Moly Bronze service involves switching to Liqui Moly oil without the introduction of additives.
• Liqui Moly Silver service includes a Pro-Line Engine Flush to remove sludge and carbon buildup from the oil circulation system.
• Liqui Moly Gold service includes Silver service and Jectron Fuel Injection System Cleaner. This cleans your injectors and maintains your fuel system to improves engine performance and efficiency.
• Liqui Moly Platinum service includes Gold service and Cera Tec Oil Additive. This prevents wear and reduces friction to improve engine performance and efficiency.

Below you can add new drain plug and crush washer, along with your choice of oil filter.

This kit also features many Popular Service Tools that make your life easier when working on your BMW:

• Turner Motorsport Magnetic Fender Cover
• Schwaben 6.5L Fluid Extractor
• Schwaben 14mm/17mm Service Wrench
• Schwaben Professional BMW/MINI Scan Tool

Have you ever been bent over your engine bay for a few hours and noticed that your belt scratched your fender? We've got you covered with the Turner Motorsport Magnetic Fender Cover. We also offer a myriad of Schwaben tools. Schwaben's Professional Scan Tool vastly simplifies diagnosing your BMW. This scan tool offers OE-level diagnostics for over 25 years of models, also allowing you to access common service features like resetting your oil service light, installing a new battery, throttle body adjustment, DPF regeneration, and more. The Schwaben Fluid extractor allows you displace 6.5L of fluid without making a mess of your workspace. Lastly, we've found that the 14mm/17mm service wrench allows you to service most of your vehicle with just one tool - one of the biggest hangups with working on a vehicle is losing your tools. Save yourself time looking for multiple different tools across your garage by owning one that does it all.

These products fit the following BMWs:

2006-2012 E90 323i 325i 325xi 328i 328xi 330i 330xi 335i 335xi
2005-2009 E60/E61 525i 525xi 528i 528xi 530i 530xi 535i
2005-2008 E85/E86 Z4 2.5i Z4 3.0si
2010-2016 F10 520i 520Li 523i 525Li 528i
2009–2017 F10/F11/F07 535i
2009-2016 E89 Z4 sDrive18i Z4 sDrive20i Z4 sDrive23i 2008-2011 Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2005-2010 E83 X3 2.5si xDrive25i X3 3.0si 
2007-2013 E82/E88 125i 128i 135i 135is
2011 E82 1 Series M Coupe
2009-2011 E84 X1 X1 xDrive/sDrive20i xDrive25i X1 xDrive28i X1 xDrive/sDrive28i xDrive35i
2004-2010 E63/E64 630i
2006-2012 E87 130i
2010+ F25 X3 sDrive18i X3 xDrive20i X3 28i X3 xDrive28i X3 xDrive35i
2006-2013 E70 X5 3.0si xDrive30i X5 xDrive 35i
2008–2014 E71 X6 xDrive35i
2008–2015 F01 740i 740i/Li
2011–2015 F30/F31 335i
2011–2016 F30 320i 328i
2013–2016 F32/F33/F36 435i
2014+ F15 X5 xdrive 35i
2014+ F16 X6 xDrive35i
2014+ F26 X4 xDrive 35i X4 M40i
2011+ F06/F12/F13 640i
2012–2016 F20/F21 M135i
2012–2017 F20 125i
2013–2016 F22/F23 M235i
2014+ F22 220i 225i 228i
2016+ F87 M2
2013–2016 F34 320i GT
2013–2016 F34 328i GT
2014–2017 F26 X4 xDrive20i