BMW 1 Series E82 (2008-2013)

Every 60-80,000 miles, we recommend replacing your spark plugs to ensure your ignition system is running optimally. Over time carbon can build up around the head of the spark plug and decrease spark strength and effectiveness, leading to weaker fuel mixture detonation, misfires, and potential check engine lights. To prevent this, have put together our High-Performance Ignition Service Kits. These kits include new Bav Auto High-Performance Ignition Coils, new spark plugs, dielectric grease, and a BMW spark plug service label to keep track of when your spark plugs were replaced.

Bav Auto's Ignition coils feature core windings that have been modified to increase firepower and promote a faster, more efficient burn. This gives your BMW/MINI increased torque in the lower range of RPM and more horsepower in the upper range. Exact improvements depend on the current condition of your engine, but you'll definitely feel the difference. They'll also improve your fuel economy.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Ensure your driving machine's peak performance with regular maintenance. Turner Motorsport offers a comprehensive service kit to keep your BMW in top shape. With varying oil change intervals based on driving habits, this kit includes:

• Seven Liters of BMW Synthetic Engine Oil
• Engine Oil Filter
• Oil Drain Plug Gasket (Included with filter kit)

For optimal results, we recommend an oil change every 10,000 miles, or every 5,000 miles for aggressive or city driving. Trust Turner Motorsport to provide the quality and precision your BMW deserves.

Featuring ECS V5 Drilled & Zinc-Coated Brake Rotors and ECS EP24 "Enthusiast Performance" Brake Pads. Everything you need to service your front and rear brakes in an afternoon in one simple kit from Turner Motorsport.

By providing it all for you in a single click, Turner has made it easier than ever to get the quality replacement matching components you need when beginning a brake service. Our brake service kit includes rotors, pads, sensors, assembly grease, and even a full compliment of set screws to make your brake replacement easy. A complete matched kit assembled by our team of experts will keep all of your brake components working in perfect harmony.

Includes the following parts:

Front & Rear ECS V5 Drilled & Zinc-Coated Brake Rotors Front & Rear ECS EP24 "Enthusiast Performance" Brake Pads Front & Rear OE Brake Pad Wear Sensors Stainless Steel Rotor Set Screws (8) AGS Brake Lubricant Packet (2) Turner Motorsport stocks a large inventory of premium brake components, including hoses, hard lines, fluids, hardware, and hi-temp lubricants. Everything you need to perform a professional quality brake service, you can find at Turner Motorsport.

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

Enhance your BMW's performance with our premium control arm upgrade kit from Turner Motorsport! This kit provides a significant handling upgrade without sacrificing ride quality. Perfect for enthusiasts looking to replace their factory control arms with sturdier, high-performance alternatives, this kit features stiffer bushings and ball joints for improved precision.

Key Benefits:

Improved Handling: Experience more precise and responsive steering, giving your BMW a sportier feel. Increased Durability: Our control arms are much sturdier than factory units, ensuring long-lasting performance. Negative Camber Adjustment: Adds approximately 0.75 degrees of negative camber to the front, enhancing cornering grip and stability. Complete Kit: Includes all four M3-specific lower control arms with mounting hardware. M3 Headlight Leveling Rod: Necessary for proper installation, ensuring your headlights are correctly aligned. Important Note for Z4 Models: For Z4 owners, please be aware that the M3 headlight level sensor rod is positioned differently. A custom solution will be required to attach the sensor rod to the control arm. Currently, we do not offer a direct solution for this issue.

Upgrade your BMW's suspension with confidence! Enjoy a smoother, more controlled ride with our premium control arm upgrade kit!