BMW Brakes & Brake Parts for BMW 1 Series E82 (2008-2013)

These are completely stock brake hoses made to fit your vehicle exactly. Ends have the same thread pitch as the stock unit and length is perfect. Designed to perform just like stock, this line will get your brakes working perfectly again. A high-quality replacement for any damaged or swelled hose.

If you are replacing your brake lines, you will need to get some fluid. While bleeding the replacement lines, make sure to put in quality, system compatible fluid to give your vehicle the best in braking.

Genuine BMW Brake Hose Rear
This item fits the following BMW Chassis:
E82 1M Coupe,E82,E90,E92,E93

The latest in the Yellow line takes all of the RSL29 characteristics and adds a bit more aggressive behavior. Friction levels go up for more initial bite and better fade resistance. Modulation and release stays close to RSL29 levels. Pad and rotor wear is a little more than on the previous Yellows but still within reasonable levels and the RSL1 is still considered an extended endurance pad. Its development stemming from GT classes at Le Mans and Nürburgring.

Since Pagid pads tend to "out-gas" we recommend using these pads with a new gas-slotted or cross-drilled rotor for the best performance. Pagid brake pads are not compatible with previously used rotors, especially if used with a carbon or Kevlar based race pad.

This item fits the following BMWs:
2008-2013 E82/88 BMW 135i, 128 with BMW Performance caliper conversion
2006-2009 E9X BMW Submodels with BMW Performance caliper conversion

Elevate your lifting experience with the Schwaben Long Low Profile - High Lift Floor Jack. Certified for excellence and designed with a keen understanding of European car enthusiasts' needs, this jack is a testament to precision, durability, and performance. Don't compromise on quality—choose the Schwaben advantage for all your lifting endeavors.

Designed with precision, crafted for performance, and backed by our lifetime replacement program, the Schwaben Long Low Profile - High Lift Floor Jack is a must-have tool for every European car aficionado. This jack is engineered to cater to the unique needs of low ground clearance vehicles, ensuring that your prized possessions are lifted with care and precision.

Key Features:

• One Pump Reach: With its innovative one-pump feature, this floor jack effortlessly reaches contact on most cars, streamlining your lifting process.
• Low Profile Advantage: Boasting a mere 2-3/4" low height and a deep-reach lift arm, this jack is tailored for those sports cars and luxury vehicles that ride close to the ground.
• Hydraulic System Protection: The dual pump pistons are expertly shielded to thwart contaminants from compromising the hydraulic system's integrity.
• Built for Durability: Crafted with heavy gauge construction and fortified with rolled edges, this floor jack guarantees unwavering strength and longevity.
• Precise Control: The U-Joint release mechanism offers meticulous control over load descent at any handle position, ensuring the safety of both you and your vehicle.
• Maneuverability Redefined: Upgraded casters allow seamless maneuverability and effortless positioning of the jack, empowering you to find that perfect lifting spot.
• Safety First: The internal by-pass valve prevents over-pumping, shielding the hydraulic system from stress-induced issues.
• Vehicle Protection: A full cover rubber saddle pad and a protective foam cover on the handle are in place to prevent any unintended damage during the lifting process.
• Impressive Capacity: With a remarkable 4000 lb. capacity, this jack is ready to tackle a range of European vehicles.
• LIFETIME REPLACEMENT: Like almost all Schwaben products, this jack is backed by our lifetime replacement program in case anything goes wrong!

Specifications:

• Min Height: 2-3/4"
• Max Height: 24"
• Handle Length: 49-1/4"
• Jack Body Length: 35"
• Length from Pivot Point to Center of Jack Pad: 22"
• Front Casters: 2-1/2" diameter x 2" width
• Saddle Diameter: 4" with full saddle pad
• Weight Capacity: 4000 lbs.
• ANSI / ASME PALD 2009 Certified

Also included are the Schwaben Aluminum 3-Ton Jack Stands. These ultra-light Schwaben jack stands only weigh 4.7 lbs each. Fit and finish on these stands show how much pride in workmanship goes into our stands. These stands feature all-aluminum construction with heavy-duty flanged bases to safely stabilize loads. Features 6 locking positions for a secure load in multiple heights. The load pin is extra heavy duty at .584 in. diameter and features a posi lock ball to ensure the pin stays in place.  

• Min. Height is 10.6".
• Max Height is 15.4".
• Large 7" diameter base.
• Outer support tube is 2-1/8" in diameter.

For replacement parts, please call us and ask for:

• ES#4430428 - Replacement Screw Set
• ES#4430429 - Replacement Front Wheel
• ES#4430430 - Replacement Caster Wheel

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Having a low profile floor jack can be a great asset for your garage, perfect for those with a lowered car as well as those that aren't. Most car owners with a lowered vehicle have been in the position of their floor jack not making the clearance needed, the low profile jack is the answer. 

• Dual pump pistons raises the saddle to maximum height in only 5 pump strokes, with minimum effort.
• Special low profile thick frame side plates and reinforced lift arm for added strength and use.
• Wide track front wheels help provide chassis torsion control and durability.
• Angular positioned pump pistons provide maximum effective pump stroke even when jack is completely under the vehicle.
• Ball bearing mounted rear swivel caster wheels for easy maneuverability.
• Side mounted handles for carrying and easy positioning.
• Overload and bypass safety valve prevents jack overload and over extension.
• Two piece quick release padded handle for storage or transport.

Details:

• Jack Capacity 2 Ton
• Max Lift Height 20"
• Low Height 3.25"
• Chassis Length 26.5"
• Overall Width 13"
• Saddle Diameter 4.5"
• Handle Lenght 50"
• Shipping Weight 50 lbs

The ultra light Schwaben jack stands only weigh 4.7 lbs each. Fit and finish on these stands just shows how much pride in workmanship goes into our stands.These stands are all aluminum construction with heavy-duty  flanged bases to safely stabilize loads. Features 6 locking positions for a secure load in multiple heights. The load pin is extra heavy duty at .584 in. diameter and features a posi lock ball to insure pin stays in place.  

Min. Height is 10.6".

Max Height is 15.4".

Large 7" diameter base.

Outer support tube is 2-1/8" in diameter.