Engineered in-house, we designed this lightweight, single-mass flywheel to provide more than 10 pounds of weight savings over the factory flywheel. While some ultra-lightweight performance flywheels are manufactured from aluminum, our designers opted for a more driveable experience with steel. The mass provided by steel helps dampen vibrations and noise, delivering near-factory refinement with most of the benefits of a lightweight flywheel: quicker throttle response, improved durability (and longevity), and more effective transfer of power to the wheels.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

When it comes to selecting a clutch to pair with a lightweight flywheel, consider the driving you’ll be doing. As a single mass flywheel eliminates the dual-mass dampening of the factory flywheel, to retain the lowest noise, lowest harshness driving experience possible, select a clutch with a dampened disc such as the ACT Heavy Duty. For dedicated track cars, a solid clutch hub is appropriate.

Our recommendations:

Street: ACT Heavy Duty
Track: ACT Xtreme for high torque cars or OE 335is LuK (with 440lbs-ft or less)
Features:

Precision machined from 4140 HT heat treated chromoly steel for exceptional toughness, even wear properties, and durability.
Material quality promotes even wear across the entire friction surface
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability and elevated temperatures
Hardness improves wear characteristics
Black oxide coated for corrosion resistance on non-friction surfaces.
8620 steel pilot bearing pin, case hardened and Precision ground for maximum wear resistance.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
SFI 1.1 tested and certified to ensure safe operation under extreme operating conditions
SFI 1.1 specifies minimum material properties and requires a 3rd party lab certification test, spinning the flywheel to 1.5x redline for 1 hour to ensure the flywheel will not burst.
Specifically designed to work with N54 architecture clutches
Step height designed to optimize clamp load and maximize the usable range of clutch wear for a long service life
Performance:

Turner Flywheel 18.6 lbs
10 lbs lighter than the factory BMW flywheel (Stock Flywheel 28.9 lbs)
Faster revs
Improved throttle response
Improved acceleration
Sportier driving experience
Stock flywheel weight - 28.9lbs
Turner single mass flywheel weight = 18.55lbs

Single Mass Flywheel Conversion:

Audible chatter from the transmission after installation is considered normal. As with most single mass flywheels, there is less dampening in the flywheel to reduce "gear noise." This chatter noise may be more present when the transmission fluid temperatures are hotter and may be intensified by other modifications. Most gearboxes will experience some chatter noise at hotter temperatures. Please be advised that this noise will disappear once the clutch pedal is depressed. This symptom may be lessened by adjusting transmission fluid weight, turning off electrical/driveline consumers (A/C, High Beams, ETC.), and by raising the RPM slightly.

Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

This item fits the following BMWs with 8 bolt flywheel and build date up to 01/2009 or earlier:
2008-01/2009 E82 BMW 135i 135is 1M
2007-01/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-01/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-01/2009 E93 BMW 335i - Convertible
2008-01/2009 E60 BMW 535i 535xi 535i xDrive

Achieve increased throttle response and acceleration with the MFactory range of single-piece Lightweight Flywheels!

Diamond Cut to exacting tolerances from Forged Chromium-Molybdenum Steel
Perfect fitment & finish ensures hassle-free installation

Designed using leading-edge Solidworks 3D CAD & Cosmos FEA software
Advanced Geometry minimizes parasitic drivetrain losses. Race transmissions built with MFactory components transfer, on average, 1-2% more power to the ground over our competitors!

Precision Balanced to over 12000rpm
Ensures the utmost reliability from our Lightweight Flywheels, which are specifically designed to reduce weight and inertia for improved engine response and acceleration

Specifications

Made from imported Japanese SAE 4140 Steel
Forged, Double Tempered and Super Sub-Zero treated for unsurpassed toughness
Proprietary Nitride surface treatment for increased surface hardness

BMW Lightweight Flywheels

• Crafted with precision from Forged Chromium-Molybdenum Steel
• Perfect fitment and finish for hassle-free installation
• Utilizes leading-edge Solidworks 3D CAD and Cosmos FEA software for design
• Advanced geometry minimizes drivetrain losses, offering 1-2% more power to the ground
• Precision balanced to exceed 12,000rpm for utmost reliability
• Made from imported Japanese SAE 4140 Steel
• Forged, double-tempered, and super sub-zero treated for unsurpassed toughness
• Proprietary Nitride surface treatment enhances surface hardness

Enhance Your Car's Performance with the Perfect Clutch-Flywheel Combination

When it's time to replace your car's clutch, you face a crucial decision: upgrade or stick with stock? In many cases, upgrading is the preferred choice, especially when you pair the right clutch with a single mass flywheel. The secret to achieving the perfect blend of performance and driving experience lies in selecting a sprung hub clutch. This option allows you to enjoy the advantages of a single mass flywheel while eliminating issues like noise, vibration, and harshness (NVH), ensuring an outstanding driving performance.

This is an OEM LuK stock dual mass flywheel. When your clutch starts to experience engagement chatter because of hot spots and wear, replacing it with this OEM dual mass flywheel will restore your vehicles driveability and have you clutch shifting smoothly again. OEM replacement for BMW part # 21207640733 and 21207598460.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Upgrade the holding power of your clutch with the Clutch Masters FX250 clutch kit.

FX250 (Stage II)

• Extra long life street system
• Holding capacity 70% over stock
• Heavy-Duty reinforced pressure plate
• Rigid organic/fiber tough disc

All Clutch Masters clutch kits come complete with:

• Pressure Plate
• Clutch Disc
• Throw-out Bearing
• Pilot Bearing or Bushing
• Alignment Tool
• Pressure Plate Bolts

This clutch kit does not include a flywheel. 

This is the stock twin mass flywheel for early N54 engines in the E82 135i, E9X 335i/xi, and E60 535i/xi (flywheel uses 8 mounting bolts). It's manufactured by OEM Shaeffler (LuK). Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008-1/2009 E82 BMW 135i
2007-1/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-1/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-1/2009 E93 BMW 335i - Convertible
2007-1/2009 E60 BMW 535i 535xi 535i xDrive

This is an OEM LuK stock twin mass flywheel for the N52 non-turbo engine in the 128i, 325i/328i/330i, 525i/528i/530i, and Z4 30i. It's manufactured by OEM supplier LuK. Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.

This clutch package is designed for high HP vehicles desiring a start performance similar to O.E. The pressure plate is Race Engineered (SS) and SFI approved with significant load increase over stage 1,2 pressure plates (+600-800 lbs.). Expect a pedal effort increase of 20%-25%. Discs are assembled with heat-treated wear resistant hubs; drive plates and springs for high load transfer and dependable operation. The sprung centers on the disc in conjunction with the marcel fin between the linings create a dual dampening effect that simulates O.E. start performance. A Performance Organic friction material with a high metal content increases torque and RPM capability and maintains low operating temperatures which reduces wear and glazing.

Stage 3 Daily Clutch Kits:

Recommended usages are daily, spirited street and occasional track
Conservatively rated to hold 500lbs/ft of torque
Featuring a solid-hub center section for use with an OE dual-mass flywheel