BMW Control Arm Replacements & Upgrades for BMW 1 Series E82 (2008-2013)

BMW’s are known to have failure prone front thrust arm bushings.  The flexible rubber bushings, even those found in M performance models, allow significant movement of the front wheels to maximize daily driving comfort, but also allow considerable alignment change.  This results in a disconnected and numb road feel, standing between you and a confidence inspiring driving experience.  Eventually the fluid filled rubber bushings fatigue and crack due to continual deflection and ozone degradation, and eventually the damping fluid leaks out resulting in complete failure. 

For the enthusiast looking for superior performance and longevity with a crisp, confidence-inspiring driving experience, our sealed ball joint monoballs are the best solution available!  Our experience with spherical front control arm ball joints go back to those we designed and used in our IMSA E90 328i and E92 M3 racecars (GS class Champions in 2011).  We wanted to offer E31, E32, E34, E38, E39, E53, E60, E63, E64, and E83 owners similar levels of handling precision and control for the track and street. 

The bearing housing is precision CNC machined from 6061-T6 anodized aluminum and features a knurled OD to ensure a perfect press fit, and utilize a sealed OEM BMW ball joint for exceptional quality and durability, making them completely at home on both the street and track with no compromise.  We have done extensive street, autocross, and track testing to ensure the ball joint used in this bushing design excels in each setting.  The advantage of a sealed ball joint is that it eliminates all unwanted deflection while still allowing complete bind-free movement throughout suspension travel, resulting in exceptional control of wheel alignment.  What you get is superior steering precision, turn-in response, direct braking feedback, and better handling.

In short, if you're seeking the ultimate in precise, predictable handling and control, with crisp braking response and a long service life that’s equally at home on the street or track - look no further. We have you covered.

We offer these thrust arms with the monoball bushings pre-installed for your convenience. Since BMW recommends the control arms be replaced for every other bushing change, we prefer to sell these as a pre-assembled set. The bushings are also available separately if you wish to source your own control arms.

Features:

Bearing housing

• Precision CNC machined from 6061-T6 blue anodized aluminum
• Knurled OD to provide the perfect fit for the wide range of thrust arm bore diameters among brands.
• CNC machined 304ss ball joint sleeve inserts, providing a precision fit between the ball joint and the subframe. 

Bearing

• OEM BMW sealed and greased ball joint for exceptional durability and service life.

Performance

• Nearly instantaneous, crisp steering and braking response.
• Maintenance free, long lasting performance. 
• Improved road feel without undesirable NVH.

Sold as a pair for RWD models only.

Click here for installation instructions.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

BMW’s are known to have failure prone front thrust arm bushings.  The flexible rubber bushings, even those found in M performance models, allow significant movement of the front wheels to maximize daily driving comfort, but also allow considerable alignment change.  This results in a disconnected and numb road feel, standing between you and a confidence inspiring driving experience.  Eventually the fluid filled rubber bushings fatigue and crack due to continual deflection and ozone degradation, and eventually the damping fluid leaks out resulting in complete failure. 

For the enthusiast looking for superior performance and longevity with a crisp, confidence-inspiring driving experience, our sealed ball joint monoballs are the best solution available!  Our experience with spherical front control arm ball joints go back to those we designed and used in our IMSA E90 328i and E92 M3 racecars (GS class Champions in 2011).  We wanted to offer E31, E32, E34, E38, E39, E53, E60, E63, E64, and E83 owners similar levels of handling precision and control for the track and street. 

The bearing housing is precision CNC machined from 6061-T6 anodized aluminum and features a knurled OD to ensure a perfect press fit, and utilize a sealed OEM BMW ball joint for exceptional quality and durability, making them completely at home on both the street and track with no compromise.  We have done extensive street, autocross, and track testing to ensure the ball joint used in this bushing design excels in each setting.  The advantage of a sealed ball joint is that it eliminates all unwanted deflection while still allowing complete bind-free movement throughout suspension travel, resulting in exceptional control of wheel alignment.  What you get is superior steering precision, turn-in response, direct braking feedback, and better handling.

In short, if you're seeking the ultimate in precise, predictable handling and control, with crisp braking response and a long service life that’s equally at home on the street or track - look no further. We have you covered.

We offer these thrust arms with the monoball bushings pre-installed for your convenience. Since BMW recommends the control arms be replaced for every other bushing change, we prefer to sell these as a pre-assembled set. The bushings are also available separately if you wish to source your own control arms.

Features:

Bearing housing

• Precision CNC machined from 6061-T6 blue anodized aluminum
• Knurled OD to provide the perfect fit for the wide range of thrust arm bore diameters among brands.
• CNC machined 304ss ball joint sleeve inserts, providing a precision fit between the ball joint and the subframe. 

Bearing

• OEM BMW sealed and greased ball joint for exceptional durability and service life.

Performance

• Nearly instantaneous, crisp steering and braking response.
• Maintenance free, long lasting performance. 
• Improved road feel without undesirable NVH.

Sold as a pair for RWD models only.

Click here for installation instructions.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

M3 upper and lower control arms are a known upgrade for non-M E82 and E9X chassis. But our Monoball Thurst Arms are even more of an upgrade over the stock M3 arms. This package bundles the Turner Monoball upper thrust arms with the stock M3 lower control arms. If there's one big fail point in the E82/E9X front suspension it's the thrust arms. The front inner thrust arm bushing is filled with dampening fluid that leaks over time. Once it's gone the bushing has the strength of a rubber band. Even though we sell two types of upgraded rubber bushings there was still room for improvement. For someone looking for superior performance and longevity these sealed monoball bushings are the best out there. 

The advantage of a monoball bearing is that it will not deflect under load. All of the rubber bushings, including the M3, move in all sorts of directions and that changes your alignment, especially when used with big brake kits or when driven hard. And when worn out, performance suffers. Our monoball sits in a CNC machined aluminum housing which has zero deflection. The monoball allows complete freedom of movement but only at the desired angles. What you get is superior steering precision, better handling from more consistent alignment, and almost infinite bushing life. And thanks to the inner liner and sealed rubber boots there's none of the extra noise or reduced service life of fully solid race bushings.

The lower M3 control arm bushings use a similar sealed monoball bushing instead of rubber. This package gives you monoball precision and performance with OE-quality components.

This item fits the following BMWs: 
2008-2012 E82 BMW 128i 135i 1M Coupe 
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan 
2006-2012 E91 BMW 328i - Wagon 
2007-2013 E92 BMW 328i 335i 335is M3 - Coupe 
2007-2013 E93 BMW 328i 335i M3 - Convertible 
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is 

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

Factory BMW eccentric bolts only allow for small toe adjustments and often slip under hard cornering, effectively changing your alignment. SPL eccentric lockout kits eliminate stock eccentric bolts - you must have adjustable rear toe arms to utilize this kit in your setup; 

Technical Specifications:

• CNC machined from 6061 aluminum
• CAD plated grade 10.9 hardware
• Include washers and bolts for both sides of your vehicle.
• Made in the USA!

Fits the following BMWs:
2006-2013 E9X BMW RWD Sub-Models
2008-2013 E82 BMW All Submodels

Run into a curb a little too hard? BMW designs these toe arms to bend in the event of an accident, to save more expensive components from damage. 

If you are looking for an aftermarket adjustable option, Turner Motorsport recommends SPL Parts e9x Adjustable rear toe arms

Genuine BMW Repair Kit For Track Control - 33322406290

SPL Parts E8x E9x non-m adjustable toe arms replace OEM Part number 33322406290 

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

When lowering your vehicle, toe alignment is thrown off. These SPL adjustable toe arms offer a wide range of toe adjustment and are a significant improvement over stock, eliminating suspension deflection and increasing handling response thanks to the FK Bushings rod ends that are Teflon lined.

Technical Specifications:

• Gundrilled 2024 Aluminum Links to reduce unsprung weight
• 6061 Aluminum Clamps and Heim Joint Spacers
• Titanium Socket Head Cap Screws
• Rotating clamp design allows for easy access to lock down your alignment settings
• Low friction 3 piece Teflon lined FK Heim joints/rod ends made in Connecticut
• Made in the USA!

Fits the following BMWs:
2006-2013 E9X BMW RWD Non-M
2008-2013 E8X BMW 128i 135i

These SPL Parts adjustable rear toe arms replace OEM part number 33322283549

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

When lowering your vehicle, toe alignment is thrown off. These SPL adjustable toe arms offer a wide range of toe adjustment and are a significant improvement over stock, eliminating suspension deflection and increasing handling response thanks to the FK Bushings rod ends that are Teflon lined.

Technical Specifications:

• Gundrilled 2024 Aluminum Links to reduce unsprung weight
• 6061 Aluminum Clamps and Heim Joint Spacers
• Titanium Socket Head Cap Screws
• Rotating clamp design allows for easy access to lock down your alignment settings
• Low friction 3 piece Teflon lined FK Heim joints/rod ends made in Connecticut
• Made in the USA!

Fits the following BMWs:
2006-2013 E9X BMW M3
2008-2013 E8X BMW 1 M

This is a replacement Genuine BMW front Right lower control arm. If you are looking for a beefier, adjustable replacement set of arms, SPL offers Titanium Series Adjustable Front Lower Street Control Arms for E8X E9X RWD

Genuine BMW Repair Kit, Wishbone, Right - 31122405860

This is a replacement Genuine BMW front left lower control arm. If you are looking for a beefier, adjustable replacement set of arms, SPL offers Titanium Series Adjustable Front Lower Street Control Arms for E8X E9X RWD

Genuine BMW Repair Kit, Wishbone, Left - 31122405859

NOW LOCATED UNDER T#338095

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible