BMW Engine Parts for BMW X Series E84 (2013-2015)

BMW N55 NGK Performance Iridium Spark Plug Set

We Price Match - Give Us A Call or Chat!

T#:568296

Part#: 97506KT

In Stock

$ 113.99 USD

Add to Wish List

Qty

$ 113.99 USD

Add to Wish List

NOTE: For the N54, these plugs are 2 Steps Colder, while for the N55 they are only 1 Step Colder. When it comes time to change your spark plugs, you may wonder about colder stepped spark plugs as many others have. Colder spark plugs work by pulling more heat out of the engine's cylinders (making them "colder") and dissipating it into the engine's head, which is then cooled by the cooling system. Depending on how you have your engine built, these could be a great addition! Colder plugs can help prevent engine knock and prevent the tip of the spark plug from melting or misfiring. There are two rules that most people tend to go by when deciding on which spark plugs to buy: The first rule of thumb is that with every 100 horsepower added, you should run spark plugs that are a step colder than your stock plugs. This is generally accepted across the motorsports community but unfortunately isn't always the most accurate measurement of when you will need colder plugs. The second rule is to go a step colder any time you massively alter cylinder temperatures by adding forced induction to an NA engine, by increasing compression ratio, after altering timing in a major way, or by changing fuel types to something with a higher octane rating such as racing fuel. Adding spark plugs that are a step colder outside of these conditions, with no real change to the engine, can actually hurt more than help by leading to spark plugs fouling quicker than normal and by making the car harder to start in cold weather conditions. We suggest talking to your engine builder or tuner before making the change, or you can call our Turner Motorsport sales staff to discuss what modifications have been made to your vehicle and see if these plugs are right for you!

Show More Show Less

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

2X Entries Into Our F80 M3 Sweepstakes

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Precision Raceworks Bucketed Low-Pressure Fuel Pump Kit - Stage 2 - B...

T#:1331979

Part#: 601-0176

In Stock

$ 419.99 USD

Add to Wish List

Qty

$ 419.99 USD

Add to Wish List

When upgrading your turbos or increasing your BMW's power potential, it's important not to overlook your fuel pump. Both low and high-pressure fuel pumps can only flow so much fuel, limiting power potential regardless of turbo size or other power adders, especially when running an ethanol blend. Upgrade your BMW fuel pump with Precision Raceworks' Low-Pressure Bucketed Fuel Pump Kits. Precision's low-pressure fuel pumps are designed to flow significantly more fuel than your BMW's stock system, ideal for customers who are upgrading their vehicles or plan to run blended fuel or E85 alone! This is a true plug-and-play solution that anyone can install in their home garage and start taking advantage of the benefits right away. Precision Raceworks' Stage 2 bucketed fuel pump kit includes a genuine Walbro 450 (F90000274) fuel pump, capable of supporting up to 575whp on 93 octane pump gas or 500whp on 100% E85! In order to prevent having to send in your fuel pump, each of Precision Raceworks' kits includes thorough instructions and all of the items required to assemble your kit at home. This prevents delays in shipping, potential damage to your stock fuel pump housing, and reduces assembly costs to keep prices low. It also improves installation as there is no guesswork on engagement and sealing of o-ring or complications and risks of tightening clamps that can poke holes in critical plastic components nearby. While all bucketless fuel pumps flow .2gpm more than a bucket design that retains the venturi, it comes at a cost. Bucketless pumps should not be driven on tanks lower than 1/4 full and should not be used for road course racing. This is not a disadvantage of only bucketless designs, but also a disadvantage for any bucket design which deletes the venturi. If you do not plan on road course or drag racing (not street racing) and are responsible at maintaining 1/4 tank of fuel during spirited driving, bucketless pumps can be a cheaper alternative for you.

Show More Show Less

Motiv ReFlex+ for BMW

T#:17970629

Part#: RFXF02UI6

In Stock

$ 859.00 USD

Add to Wish List

Qty

$ 859.00 USD

Add to Wish List

The MOTIV ReFlex+ is an Advanced I/O Integration module allowing a level of precise control of auxiliary components. In addition, the ReFlex can incorporate external data into the factory DME/ECU in parallel through optional CANbus integration. Utilizing the CANbus option, multiple digital and analog signals can be used by the DME/ECU for safety, data logging, or adaptive tuning features. It is unique in its ability to function as a separate standalone, as well as a parallel module in conjunction with the DME/ECU. The ReFlex provides the most accurate and precise supplementary sequential fuel injection with the ability to control other advanced features all in one place. It brings a new level of control, function, and versatility to tuning any modern-day vehicle. Preset crank and cam trigger for most modern-day BMW engines, as well as fully configurable triggers to be synched on any vehicle application. Configurable to operate on 4, 5, 6, and 8-cylinder engines. 3 Point MAP sensor calibration table makes it configurable for almost any MAP or TMAP sensor. Sequential Port Injection with the ability to sense individual injector failures on 4 to 8-cylinder engines. Built-in Ethanol Content Analyzer. The Re|Flex firmware and XDFs include ethanol compensation tables to scale properly for varying ethanol % based on real-time input from the sensor. 2x Additional Outputs. These outputs have 12x12 resolution tables for control in TunerPro R/T. These can be configured to run as on/off, digital, frequency (25hz), or PID. Boost Control WGDC Methanol Solenoid Control PWM (for use with valves such as the Aquamist FAV and the ProMeth Pulse Valve) Nitrous Solenoid Control PWM Auxiliary fuel pump relay trigger 2x Inputs Ethanol Content Sensor Fuel Pressure Sensor (0-10bar) Oil Pressure (0-10bar) Coolant Pressure (0-10bar) EGBP/EMAP (0-10bar) CANbus (not required) enabled communication for the transmission and receiving of digital signals for fully DME/ECU integrated control of external modifications. The CANbus communications also allow for data and errors to be transmitted to and from the vehicle's engine control computer in order to add safeguards and implement engine trips and fail safes. Logging via OBDII is still fully functional and is not affected at all by the communication with the Re|Flex. Some of the developments underway include: Error reporting to and from factory ECU for unparalleled safety Output WGDC by converting an EWG signal to a more conventional DC output for controlling standard 3port and 4port boost solenoids for use with external WG’s The ability to datalog non-factory parameters such as ethanol content, additional pressure sensor, PI IDC, and more! These features make the Re|Flex the most powerful and safest supplementary and auxiliary controller on the market. However, this is only the beginning. As flash platforms find the need for more accessories to control, the Re|Flex was designed to be updated easily by the end user in order to add functionality as it is developed.

Show More Show Less

BMW Oil Cap Crankcase Breather - All BMW w/2 prong oil fill cap ...

2X Entries Into Our F80 M3 Sweepstakes

T#:558084

Part#: VTT-CRANK-BREATH

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Show More Show Less

BMW B46 B48 B58 Motiv ReFlex 0-10 Bar Pressure Sensor

T#:28537533

Part#: 101-0216

Ships in 2 Business Days

$ 105.00 USD

Add to Wish List

Qty

$ 105.00 USD

Add to Wish List

BMW B46 B48 B58 Motiv ReFlex 0-10 Bar Pressure Sensor is designed for accurate measurement of fluid and air pressure in high-performance applications. Ideal for monitoring a variety of pressures including fuel, boost, coolant, and oil, this sensor provides crucial data for optimizing vehicle performance.

Featuring a 2-Pin DTM connector, this sensor offers a direct plug-and-play connection to the ReFlex+ harness, ensuring a seamless integration with flash platforms via CANbus. Each ReFlex+ unit can support up to two of these sensors, allowing for comprehensive monitoring.

Versatile Measurement: Capable of measuring fuel pressure, boost, coolant, oil, and other fluids.
Easy Integration: 2-Pin DTM connector provides a direct plug-and-play connection.
Comprehensive Monitoring: Supports integration of up to two sensors per ReFlex+ unit.
High-Performance Design: Designed to handle high pressures and deliver accurate readings.

For optimal installation, consider using the 3/8 Female to 3/8 Male SAE Quick Disconnect Adapter with a 1/8" NPT port on an ethanol sensor or the 5/16 Female to 5/16 Male SAE Quick Disconnect Adapter with a 1/8" NPT port on a factory fuel line. Please note that the ethanol sensor is not included.

Show More Show Less

BMW B46 B48 Motiv ReFlex Plug-n-Play Ethanol Sensor Harness

For Vehicles With Motiv ReFlex Unit Currently Installed Only

T#:22723690

Part#: 101-0212

In Stock

$ 49.00 USD

Add to Wish List

Qty

$ 49.00 USD

Add to Wish List

BMW B46 B48 Motiv ReFlex Plug-n-Play Ethanol Sensor Harness simplifies the integration of an ethanol content sensor into your BMW's Re|Flex system. This harness is designed to enhance your vehicle's performance by scaling the sequential port injection based on real-time ethanol content, eliminating the need for manual adjustments. Key benefits include:

Effortless Installation: Plug-n-play design makes it easy to connect an ethanol content sensor without extensive modifications.
Real-Time Adjustments: Allows for automatic scaling of port injection based on real-time ethanol content, optimizing engine performance.
Seamless Integration: For CANbus integrated vehicles, it facilitates integration with the factory DME/ECU (pending feature release by tuning platforms).
No Manual Flashes Required: Removes the need for ground disconnection or map switching on your port injection controller.

Please note that the ethanol sensor is not included with this harness.

Show More Show Less

BMW N20 NGK Performance Iridium Two-Step Colder Spark Plug Set ...

We Price Match - Give Us A Call or Chat!

T#:594498

Part#: 97506KT1

In Stock

$ 75.99 USD

Add to Wish List

Qty

$ 75.99 USD

Add to Wish List

When it comes time to change your spark plugs, you may wonder about colder stepped spark plugs as many others have. Colder spark plugs work by pulling more heat out of the engine's cylinders (making them "colder") and dissipating it into the engine's head, which is then cooled by the cooling system. Depending on how you have your engine built, these could be a great addition! Colder plugs can help prevent engine knock and prevent the tip of the spark plug from melting or misfiring.

Show More Show Less

Precision Raceworks Ethanol 360 Fittings - 5/16" (7.89mm)

Universal Product - Please confirm your fuel line size prior to ordering

T#:37757295

Part#: 601-0240

Ships in 8 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

The Precision Raceworks Ethanol 360 fuel line fittings are designed to work in almost any application where you have 5/16" or 7.89mm quick-connect fittings and need to add a flex fuel sensor. These fittings work with almost all ethanol sensors without the need to cut and splice or replace entire line sets. This is a perfect way to add an ethanol sensor to your vehicle while maintaining existing fuel lines.

Show More Show Less

Precision Raceworks Replacement Ignition Coil - Blue

T#:4333508

Part#: 201-0091

In Stock

$ 39.99 USD

Add to Wish List

Qty

$ 39.99 USD

Add to Wish List

Replaces individual coils found in the Precision Raceworks Ignition Kit.

Vargas N54/55 Billet Crank Seal Guard - BMW N54 N55 3.0L

2X Entries Into Our F80 M3 Sweepstakes

T#:638889

Part#: VTT-CRANKGUARD

In Stock

Starting at $ 89.99 USD

Add to Wish List

Starting at $ 89.99 USD

Add to Wish List

It is a well-known issue on the BMW N54/55 platforms that your serpentine belt can fail for various reasons. When this happens, there is a high chance of the belt getting sucked behind the front damper pulley and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure. Even if you do not lose the engine, it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT, even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Vargas' seal is different from those already on market in two major ways. Firstly, it is not offensively priced. Secondly, it is 100% billet with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long-term corrosion resistance. Crank Seal Guard includes: One VTT Billet N54/55 Crank Seal Guard Two extended 12.9 Grade bolts, and two stainless washers We highly recommend you install WITH a crank bolt capture at the same time, as you have to remove the damper anyway. Then you will get the benefit of helping eliminate the dreaded spun crank hub and the crank seal issue

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

2X Entries Into Our F80 M3 Sweepstakes

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

BMW B58 3.0L ReFlex+ Main Injector Harness - Inline-6

T#:29201081

Part#: 900.1008

In Stock

$ 200.00 USD

Add to Wish List

Qty

$ 200.00 USD

Add to Wish List

BMW B58 3.0L ReFlex+ Main Injector Harness - Inline-6 offers a seamless integration solution for your turbocharged BMW inline-6 engine. Designed to work with the Motive ReFlex Control Unit, this plug-n-play harness ensures a hassle-free installation process for your 6 EV6/USCAR injectors.

Direct Plug-N-Play Installation: Connects directly to the ReFlex+ Control Unit and your EV6/USCAR injectors.
Versatile Connector Options: Includes DTM 3-Pin and 2-Pin connectors for integration with ethanol content sensors and external sensors.
Multiple Sensor Connectors: Features connections for a 0-10 Bar Pressure Sensor and a 0-5v sensor.
Auxiliary Output Wires: Provides 3x unterminated wires for additional low-side triggers from the ReFlex+ Control Unit.
Easy Connection: DTM 8-Pin connector allows for straightforward setup with ReFlex+ Install Harnesses.

Turner Motorsport's harness ensures efficient and reliable performance, streamlining the process of integrating your ReFlex+ Control Unit with your BMW B58 engine.

Show More Show Less

Braille Performance Lightweight AGM Battery - B14115 - 11.5lbs ...

T#:558037

Part#: B14115

Ships in 6 Business Days

$ 204.99 USD

Add to Wish List

Qty

$ 204.99 USD

Add to Wish List

When building a car for the track, one of the most important factors to consider is weight. Stock batteries can weigh up to almost 50 pounds and are unnecessarily large, designed to power a host of systems not normally used in a track car (radios, lighting, etc.). What can you do to cut weight the weight without affecting your cars operation? This is where Braille Battery comes in with their long line of performance lightweight battery options! Designed to provide the highest cranking power possible while being up to 75% lighter, Braille Battery is one of the foremost leaders in automotive racing batteries with nothing but high quality, high output batteries in mind!

Show More Show Less

Replacement Fuel Filter Element - 6 Micron | Precision Raceworks ...

T#:38161701

Part#: 101-0257

In Stock

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Replacement Fuel Filter Element - 6 Micron | Precision Raceworks is designed for BMW and high-performance fuel systems, ensuring optimal fuel flow and superior filtration. This high-efficiency 6-micron filter element effectively captures contaminants, preventing debris from reaching fuel injectors and maintaining peak engine performance.

Regular maintenance of your fuel filter is essential for maximizing fuel system efficiency. Whether for racing or daily driving, this replacement element keeps your fuel system running at its best.

6-micron filtration – Removes fine particles and contaminants to protect engine components
High-performance compatibility – Designed for use with Precision Raceworks inline fuel filters
Optimized fuel flow – Maintains consistent fuel delivery for peak performance
Durable construction – Engineered for long-lasting reliability in high-demand applications
Easy replacement – Simple installation for routine maintenance
Ideal for both street and track use – Ensures clean fuel supply for all driving conditions

Fuel Filter Replacement Guidelines:

Racing applications: Inspect at least twice per season and replace as needed
Daily driving: Inspect at least once a year or every 6,000 miles, replacing as necessary

Ensure your BMW fuel system stays clean and efficient with the Replacement Fuel Filter Element - 6 Micron | Precision Raceworks, the ultimate choice for maintaining performance and reliability.

Show More Show Less

NGK Spark Plugs - Set Of 4 N20 2.0L

We Price Match - Give Us A Call or Chat!

T#:568655

Part#: 121200396642KT

In Stock

$ 75.99 USD

Add to Wish List

Qty

$ 75.99 USD

Add to Wish List

NGK Spark Plug - Set Of 4 (121200396642)

Upgrade your engine's performance with the NGK Spark Plug Set (Part Number: 121200396642). This set contains four top-quality spark plugs meticulously designed to optimize ignition and fuel combustion within your vehicle's engine.

NGK, a renowned brand in automotive components, guarantees reliability and efficiency in these spark plugs. Crafted with precision and durability, these plugs meet or surpass OEM standards, ensuring consistent and smooth ignition.

Keep your engine operating at its peak performance with the NGK Spark Plug set, providing reliable ignition for enhanced engine efficiency.

Show More Show Less

Port Injection Fuel Line For Top Mount Fuel Rail - N54 N55

T#:38094311

Part#: 201-0188

In Stock

$ 54.99 USD

Add to Wish List

Qty

$ 54.99 USD

Add to Wish List

Port Injection Fuel Line For Top Mount Fuel Rail - N54 N55 is designed for seamless compatibility with most aftermarket intake manifolds featuring top mount port injection. It works with leading brands such as Black Market Parts, BKC, BMS, Sharp Custom, Doc Race, and more, ensuring a high-performance fuel delivery solution for BMW N54 and N55 engines.

Constructed with premium 6061 aluminum and anodized for 100% E85 compliance, this fuel line is engineered for durability and optimal fuel flow. The female quick connectors feature an air hose-style quick connect with dual seals (primary and secondary) to eliminate any risk of fuel leaks. Precision Raceworks utilizes Smooth Bore PTFE hose, a trusted component in high-end E85 applications worldwide.

This plug-and-play solution is fully compatible with both factory and aftermarket fuel lines, providing an easy, reliable way to supply fuel to the port injection system of your upgraded intake manifold.

Seamless fit – Compatible with most aftermarket top mount port injection manifolds
Durable construction – Machined from 6061 aluminum and anodized for E85 compatibility
Leak-proof design – Dual-seal quick connectors for maximum fuel safety
High-performance fuel delivery – Utilizes Smooth Bore PTFE hose for optimal flow
Easy installation – Direct plug-and-play with factory and aftermarket fuel lines

Show More Show Less

Motiv ReFlex+ Control Unit

T#:29101684

Part#: 900.1001

In Stock

$ 729.00 USD

Add to Wish List

Qty

$ 729.00 USD

Add to Wish List

The motive ReFlex+ Control Unit is an advanced I/O integration module that allows precise control of aftermarket components and sends data to the factory DME (ECU) via CANbus communication, expanding performance tuning capabilities. This control unit allows for precise control of fuel pumps, methanol injection kits, nitrous kits, boost controllers, relay triggers, port injection systems, flex fuel systems, and more. Supporting sequential port injection for up to eight injectors and real-time monitoring of injectors, this unit is a great choice for precise control of fuel delivery to your engine.

Show More Show Less

Precision Raceworks Upgraded Fuel Lines W/ Ethanol Sensor Connection ...

T#:10714270

Part#: 201-0247

In Stock

$ 164.99 USD

Add to Wish List

Qty

$ 164.99 USD

Add to Wish List

NOTE: Requires a Continental Flex Fuel Sensor be utilized, will not directly replace the OE fuel line. The Precision Raceworks AN6 Fuel line upgrade is a direct replacement from the fuel filter on the driver’s side of the car to the high-pressure fuel pump. All connections are designed in-house and machined from 6061 aluminum then anodized for 100% E85 compliance. All female connectors have 2 seals (a primary and secondary seal) to guarantee no possible fuel leaks. The fuel line used by Precision Raceworks is smooth bore PTFE hose that is wrapped in a Stainless Steel braiding for protection and then a nylon braiding to protect surfaces. This type of hose is used in high-end E85 applications built all over the world. This is a better than OEM quality solution to help you achieve the needs of your high horsepower build on E85. Specifications: Fuel hose type: PTFE Smooth Bore Line Size: -6AN (1/2") Connection Style: OEM Quick Connect Connector Material: 6061 Aircraft Grade Aluminum Connects to flex fuel sensor: Yes

Show More Show Less

Precision Raceworks Ethanol 360 Fittings - 3/8" (9.49mm)

Universal Product - Please confirm your fuel line size prior to ordering

T#:37892104

Part#: 601-0288

In Stock

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

The Precision Raceworks Ethanol 360 fuel line fittings are designed to work in almost any application where you have 3/8" (9.49mm) quick-connect fittings and need to add a flex fuel sensor. These fittings work with almost all ethanol sensors without the need to cut and splice or replace entire line sets. This is a perfect way to add an ethanol sensor to your vehicle while maintaining existing fuel lines.

Show More Show Less

Braille Performance Lightweight Advanced AGM Battery - B2015 - 15lbs ...

T#:558038

Part#: B2015

Ships in 6 Business Days

$ 237.99 USD

Add to Wish List

Qty

$ 237.99 USD

Add to Wish List

When building a car for the track, one of the most important factors to consider is weight. Stock batteries can weigh up to almost 50 pounds and are unnecessarily large, designed to power a host of systems not normally used in a track car (radios, lighting, etc.). What can you do to cut weight the weight without affecting your cars operation? This is where Braille Battery comes in with their long line of performance lightweight battery options! Designed to provide the highest cranking power possible while being up to 75% lighter, Braille Battery is one of the foremost leaders in automotive racing batteries with nothing but high quality, high output batteries in mind! The B2015 is Braille's most popular non-carbon racing battery and is able to start larger engines easily for racing and offers daily driving capability for most 4 and 6 cylinders engine vehicles. Physical Specifications: BCI Group: All sizes Weight: 15lbs / 6.8kg Length: 6.8" / 173mm Width: 3.4" / 86mm Height: 6.1" / 155mm Polarity: Right Side Positive Performance Specifications: Voltage: 12 Full Charge Voltage: 13.2 Pulse Cranking Amps (PCA): 1067 Amp Hour (AH): 21 Life Cycle @ 10% DOD: 3100 *THIS BATTERY REQUIRES A CUSTOM MOUNTING SOLUTION. The size and weight are significantly smaller than a stock battery and will not be held in place by the stock battery mount*

Show More Show Less

Precision Raceworks Universal Fuel Line NPT Tap - Quick Disconnect Ad...

T#:38161736

Part#: 201-0405

In Stock

$ 24.99 USD

Add to Wish List

Qty

$ 24.99 USD

Add to Wish List

This fitting allows you to install a 1/8" npt port anywhere you have an existing quick connect Compatible with the Motiv 0-10 Bar pressure sensor

Precision Raceworks Replacement Spark Plug Wires - For 601-0021 & 601...

T#:3786918

Part#: 201-0002

In Stock

$ 69.99 USD

Add to Wish List

Qty

$ 69.99 USD

Add to Wish List

Precision Raceworks' BMW N54 / N55 replacement spark plug wires are the same plug wires that are included in their High-Performance Ignition Kits 601-0021 & 601-0021-1

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 2 Business Days

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Motiv ReFlex Lite: Advanced Sequential Injector Controller - Inline-6...

T#:29234298

Part#: 910.1011

In Stock

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

The ReFlex LITE is a simple yet elegant fueling solution for direct injected vehicles that need to add more fuel by installing a port injection system to keep up with their modifications to the vehicle. Using the same precise form of sequential fuel injection as the ReFlex+, the ReFlex LITE brings a more affordable fuel controller without the additional features of the ReFlex+. Sequential port fuel injection for inline-6 engines Firmware and maps are available for multiple vehicles FREE on our website High resolution calibration tables 24x24 cell RPM vs MAP 0-48psi MAP pressure range 250RPM increments up to 8500RPM High resolution datalogging Fault detection status available to monitor in TunerPRO RT Compact in size Universal fitment Simple installation Please Note: The ReFlex LITE does NOT have the ability to analyze and transmit ethanol content to an ECU.

Show More Show Less

Braille Lightweight Advanced AGM Battery - B3121 - 21lbs

T#:558042

Part#: B3121

Ships in 7 Business Days

$ 270.99 USD

Add to Wish List

Qty

$ 270.99 USD

Add to Wish List

When building a car for the track, one of the most important factors to consider is weight. Stock batteries can weigh up to almost 50 pounds and are unnecessarily large, designed to power a host of systems not normally used in a track car (radios, lighting, etc.). What can you do to cut weight the weight without affecting your car's operation? This is where Braille Battery comes in with their long line of performance lightweight battery options! Designed to provide the highest cranking power possible while being up to 75% lighter, Braille Battery is one of the foremost leaders in automotive racing batteries with nothing but high quality, high output batteries in mind! The B3121 battery from Braille is their lightest do-everything battery available, offering 1380 pulse cranking amps that can crank over V8 engines with ease while still coming in at under 22 pounds, half of the weight of a standard Group 34 battery! This is thanks to their Advanced AGM racing technology that allows them to put a ton of power into a very small package. Physical Specifications: BCI Group: All sizes Weight: 21lbs / 9.5kg Length: 6.6" / 168mm Width: 5.2" / 132mm Height: 6.8" / 173mm Polarity: Right Side Positive Terminal Type: Steel terminal block with M6 bolt Performance Specifications: Voltage: 12v Recharge Voltage: 14.4V – 14.6V Maintenance charge voltage: 13.8V 5s Pulse Cranking Amps (PCA): 1380 10s PDC: 124 Amp Hour (Ah): 31 Watt Hour (Wh): 372 Life Cycle @ 10% DOD: 3100 Charging Temperature 0C to 50C Discharge Temperature range -40C to +60C Storage temperature -40C to +60C *THIS BATTERY REQUIRES A CUSTOM MOUNTING SOLUTION. The size and weight are significantly smaller than a stock battery and will not be held in place by the stock battery mount*

Show More Show Less

Precision Raceworks Replacement Ignition Coil - Black

T#:24843089

Part#: 201-0121

Ships on Sep 16, 2026

$ 39.99 USD

Add to Wish List

Qty

$ 39.99 USD

Add to Wish List

Vargas Ignition Coil Kit (Blue) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309605

Part#: VTT-COIL-N5X-BLU

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

3/8" Quick Disconnect Adapter With 1/8" NPT Port

T#:29500156

Part#: 200.1105

In Stock

$ 24.00 USD

Add to Wish List

Qty

$ 24.00 USD

Add to Wish List

Quick disconnect adapters (QDA) are commonly used to adapt different components into vehicle fuel systems without requiring permanent modification. These adaptersÂ are machined from high-grade aluminum and anodized for corrosion resistance. QDAs incorporate VitonÂ© o-rings which are compatible with most types of fuel, solvents and oils. QDAs maintain a reliable leak-proof seal under normal fuel injection system operating pressures. This particular QDA is sized perfectly to adapt right between the fuel line you were going to connect to your ethanol sensor. 3/8" (9.5mm) female quick disconnect 3/8" (9.5mm) male quick disconnect 1/8" Female pipe thread port * Viton© o-rings Crecent-lock system E-85 compatible Black anodized aluminum

Show More Show Less

Innovate LC-2 Wideband O2 Controller Kit

T#:28836410

Part#: 38770

In Stock at Vendor

$ 212.99 USD

Add to Wish List

Qty

$ 212.99 USD

Add to Wish List

Features & Benefits:

Two configurable linear 0-5V analog outputs Ability to calibrate O2 sensors for maximum accuracy Includes LC-2 controller and Bosch wideband O2 sensor Comes with a program cable, manual, and a 10 ft. sensor cable Includes a 1-inch mild steel exhaust bung Innovate MTS serial in/out capability Integrated dual-color status LED (green/red) Patented DirectDigital™ wideband sensor control Positive lock connectors for all connections Real-time display data on screen or with the powerful LogWorks software Range:

AFR (Air-Fuel Ratio) range from 7.4:1 to 22.4:1 (0.5 to 1.5 lambda)

Show More Show Less

Vargas Ignition Coil Kit (Red) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309610

Part#: VTT-COIL-N5X-RED

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

Precision Raceworks High Performance Fuel Pump Kit - Stage 3 - BMW E-...

T#:5216002

Part#: 601-0110

In Stock

$ 868.99 USD

Add to Wish List

Qty

$ 868.99 USD

Add to Wish List

If you are looking to get more power out of your BMW, it's important not to forget your fueling system! Your low and high-pressure fuel pumps can only flow so much fuel, limiting power potential regardless of turbo size or other power adders, especially true when running ethanol blends. Bring your fuel system up to par with Precision Raceworks' E-Chassis High-Performance Fuel Pump Kits! Precision's low-pressure fuel pumps are designed to flow significantly more fuel than your BMW's stock system, ideal for customers who are upgrading their vehicles or plan to run blended fuel or E85 alone. Best of all, these pumps ship completely assembled and ready to install! New pump, new fuel filter, and new sending unit included! This is a true plug-and-play solution that anyone can install in their home garage and start taking advantage of the benefits right away. By design, a fuel pump such as this is ideal for daily driving and racing applications of all kinds. This system keeps the primary pump fully submerged in fuel regardless of tank level or the g-force the car is subjected to. Precision Raceworks' Stage 3 bucketed fuel pump kit includes a Walbro 450 (F90000274) fuel pump, capable of supporting up to 1000whp on 93 octane pump gas or 875whp on 100% E85! Even better yet? No wires to cut or splice, nothing to assemble, 100% OEM quality, and drop-in ready. Included in the box New genuine OEM fuel pump bucket assembly (Pre-assembled with genuine Walbro 450 pump) Includes new fuel sending unit (fuel level sensor) New primary and secondary fuel filters Stage 3 Specifications: Horsepower Supported Pump Gas: ~1000whp Horsepower Supported 100% E85: ~875whp Aftermarket EKP Required: No **Some European Spec vehicles may require the re-use of the top hat due to differences in emissions requirements.

Show More Show Less

ReFlex+ Install Harness - Flying Lead

T#:29201083

Part#: 900.1016

Ships in 2 Business Days

$ 95.00 USD

Add to Wish List

Qty

$ 95.00 USD

Add to Wish List

A flying lead harness is a wiring harness that is unterminated at one end and has an excess length of wire so that installation can be customized by the end user. That makes this section of the ReFlex+ Install Harness truly universal. On one end, this harness has an 8-pin connector to plug into any one of our ReFlex+ Main Injector Harnesses. The other end of each wire is unterminated and will be connected to the appropriate sensor, ground, or power supply based on installation instructions. Each harness has a wire for: Switched +12v Input w/ inline fuse +5v Input Ground Can HI Can Lo Cam Sensor Signal Crank Sensor Signal Map Sensor Signal

Show More Show Less

Precision Raceworks Universal Adjustable Fuel Pressure Regulator W/ 1...

T#:38195449

Part#: 501-0043

In Stock

$ 159.99 USD

Add to Wish List

Qty

$ 159.99 USD

Add to Wish List

Adjust your fuel pressure as needed. Thanks to the 1:1 boost reference, fuel pressure will increase as boost pressure increases, ensuring fuel delivery remains optimal under all conditions.

Braille Performance Intensity Carbon Lithium-ION Battery - i48CX - 10...

This item is classified as Hazardous Materials and requires special shipping and handling. We cannot ship this item out of the US or with priority shi

T#:558047

Part#: I48CX

Ships in 5 Business Days

$ 1,164.99 USD

Add to Wish List

Qty

$ 1,164.99 USD

Add to Wish List

The ultra-lightweight, standard height I48CX lithium-ION battery from Braille Battery is a popular choice among BMW enthusiasts looking for a drop-in replacement battery that shaves off a ton of weight, 35 pounds in total! Thanks to the Group 48 design of this battery, no modifications are needed for installation. This is perfect for anyone looking to drive their car both on and off of the track, without any negative side effects, and wants a battery with a 10-15 year life span!

Show More Show Less

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733531

Part#: VTT-CRANKHUB-5

Ships on Sep 16, 2026

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Precision Raceworks Bucketed High Performance Fuel Pump Kit - Stage 2...

T#:8169508

Part#: 601-0116

In Stock

$ 594.99 USD

Add to Wish List

Qty

$ 594.99 USD

Add to Wish List

The Precision Raceworks E9x / E8x LOW PRESSURE BUCKETED FUEL PUMPS are designed for customers looking to run all blends of E85 and flow up to 3.9 liters per minute. The included Genuine Walbro 535 (F90000295) fuel pump is capable of flowing up to 350% more fuel than the factory fuel pump and is 100% E85 compliant. Precision Raceworks' Stage 2.5 V2 bucketed fuel pump comes with a single Walbro 535 (F90000295) fuel pump. This pump can support up to 650whp (Rated for 550whp on 100% E85) and is ready to grow with you as your needs demand. Unlike other manufacturers, Precision Raceworks is the only company featuring a bucketed kit with a modular design. This means you can purchase their stage 3 pump module or Stage 3.5 module and upgrade the pump as your needs change. If you are looking for a 100% assembled drop-in-ready solution, this is the choice for you! **Some European Spec vehicles may require the re-use of the top hat due to differences in emissions requirements. This is a true plug-and-play solution that anyone can install in their home garage and start taking advantage of the benefits right away. Features & Specifications: Lock Ring Tool Included Pump flow 72psi (5bar): 1.0 GPM / 3.9 LPM Pump Weight: 3.98 lbs Horsepower Supported Pump Gas: 650 Horsepower Supported 100% E85: 550 Aftermarket EKP Required: No

Show More Show Less

Precision Raceworks High Performance Ignition Kit - Blue Coils - BMW ...

T#:26205125

Part#: 601-0149-1

Ships on Sep 16, 2026

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

Rid your BMW's N55 of misfires, sluggish throttle response, rough idle, and power loss with Precision Raceworks' High-Performance Ignition Kit! Precision Raceworks' ignition kit is designed to fit any vehicle with an N55 engine and offers the highest output of any kit on the market! Featuring 100% Plug-&-Play connections, low resistance 50ohm/ft proprietary plug wires, and design technology from Marine and Aerospace applications, these coils are guaranteed to output consistent high voltage and current for optimal ignition system performance and reliability. Every component in this kit meets or exceeds OEM quality and features premium seals for dust and water resistance. While coils do not directly increase horsepower, stock BMW coils can wear out quickly, resulting in underperforming voltage and current output. This often leads to weaker spark intensity and reduced power output. Due to the increased voltage and current output, many customers have seen as much as 20+ whp/wtq gained by switching to Precision Raceworks coils over all other coils on the market! By upgrading to Precision's Performance Ignition Kit, spark quality can be restored, and lost power regained often with the additional power beyond what other coils provide. No software tune is required for installation or operation, but if desired, coil output can be increased to 118mJ from most software tuning companies!

Show More Show Less

BMW N54 Replacement Coil Power Harness - Set Of 6 - Manifold Location...

T#:24112786

Part#: 201-0008-1

In Stock

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Black Market Parts Low-Pressure Bucketless Fuel Pump Kit - Stage 3 - ...

T#:5215998

Part#: 601-0018

In Stock

$ 549.99 USD

Add to Wish List

Qty

$ 549.99 USD

Add to Wish List

When upgrading your turbos or increasing your BMW's power potential, it's important not to overlook your fuel pump. Both low and high-pressure fuel pumps can only flow so much fuel, limiting power potential regardless of turbo size or other power adders, especially when running ethanol blends. If you are looking to get more power out of your BMW, it's important not to forget your fueling system! Your low and high-pressure fuel pumps can only flow so much fuel, limiting power potential regardless of turbo size or other power adders, especially true when running an ethanol blend. Bring your fuel system up to par with the Black Market Parts (By Precision Raceworks) Low-Pressure Bucketless Fuel Pump! Precision's low-pressure fuel pumps are designed to flow significantly more fuel than your BMW's stock system, ideal for customers who are upgrading their vehicles or plan to run blended fuel or E85 alone. This is a true plug-and-play solution that anyone can install in their home garage and start taking advantage of the benefits right away. The Black Market Parts Stage 3 bucketless fuel pump kit includes a genuine Walbro 450 (F90000274) fuel pump, of supporting up to 1050whp on 93 octane pump gas or 875whp on 100% E85, and is the perfect modular pump to get you started! Since Precision Raceworks is always looking ahead, they have designed their modular bucketless fuel pump to allow you to upgrade your fuel pump as needed! With an open expansion slot ready to use, just a simple Stage 3.5 or Stage 4 module is all you need to purchase to increase your fueling capabilities. While all bucketless fuel pumps flow .2gpm more than a bucket design that retains the venturi, it comes at a cost. Bucketless pumps should not be driven on tanks lower than 1/4 full and should not be used for road course or drag racing. This is not a disadvantage of only bucketless designs, but also a disadvantage for any bucket design which deletes the venturi. If you do not plan on road course racing (not street racing) and are responsible at maintaining 1/4 tank of fuel during spirited driving, bucketless pumps can be a cheaper alternative for you. Stage 2 Specifications: Horsepower Supported Pump Gas: ~1050whp Horsepower Supported 100% E85: ~875whp Aftermarket EKP Required: No *To reach the advertised ability of these fuel pumps use of the Precision Raceworks in-tank filter regulator assembly is required.

Show More Show Less

Braille Performance GreenLite Lithium-ION Battery - G30 - 5.5lbs ...

T#:558046

Part#: G30

Ships in 7 Business Days

$ 522.99 USD

Add to Wish List

Qty

$ 522.99 USD

Add to Wish List

The G30 lithium battery from Braille is designed for the Import Tuner market (4 and 6 cylinder) for track use and has enough power for small black V8 race cars and hot rods with light electrical demands/accessories and standard compression. The G30 comes in the popular ETX 30 Group size, just like the B3121 AGM, so it is small and light enough to mount in a variety of locations. Incorporated in this battery is the same technology used in their race winning batteries used by nearly every OEM developer in classes ranging from SCCA to Formula 1.

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Clear - BMW N52 N...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122266

Part#: VTTFILTERCAPCLR

Ships in 2 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

Endurance Series AGM Battery - B48-H6-L3

T#:36947237

Part#: B48-H6-L3

Ships in 5 Business Days

$ 398.99 USD

Add to Wish List

Qty

$ 398.99 USD

Add to Wish List

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Blue - BMW N52 N5...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122267

Part#: VTTFILTERCAPBLUE

Ships in 6 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

Vargas Burnt Titanium Magnetic Oil Drain Plug - M12 X 1.5

2X Entries Into Our F80 M3 Sweepstakes

T#:51813315

Part#: VTT-TI-DRAIN

Ships in 7 Business Days

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

The VTT Burnt Titanium Magnetic Oil Drain Plug is a critical upgrade for any performance enthusiast looking to maximize engine longevity.

Precision Raceworks In-Line Micro Regulator - 5 Bar

T#:38094305

Part#: 601-0260

Back Ordered

$ 64.99 USD

Add to Wish List

Qty

$ 64.99 USD

Add to Wish List

For enthusiasts seeking to regulate fuel pressure at the engine without the complexities of manual adjustments or the need for a 1:1 boost reference, a preset fuel pressure regulator offers an ideal solution. These compact regulators are designed for straightforward installation and consistent performance.

Show More Show Less

Replacement Fuel Filter Element - Single Open 10 Micron | Precision R...

T#:38161702

Part#: 101-0256

Ships in 10 Business Days

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Replacement Fuel Filter Element - 10 Micron | Precision Raceworks offers excellent filtration for BMW and high-performance fuel systems, ensuring that larger particles and contaminants are filtered out to maintain optimal engine function. This 10-micron replacement filter element is designed to work seamlessly with Precision Raceworks inline fuel filters, delivering superior protection to your fuel system components, including injectors and fuel pumps.

Whether you're racing on the track or using your vehicle for daily driving, this replacement fuel filter element keeps your fuel system performing at its best by providing reliable filtration and smooth fuel delivery.

10-micron filtration – Effectively captures larger particles and contaminants to protect fuel system components
Maintains fuel flow – Supports smooth fuel delivery for consistent engine performance
Durable construction – Crafted with high-quality materials for long-lasting use under various conditions
Seamless integration – Direct replacement for Precision Raceworks inline fuel filters
Versatile use – Perfect for daily driving, street, and high-performance applications
Easy to replace – Simple maintenance to keep your fuel system clean and efficient

Fuel Filter Replacement Guidelines:

Racing applications: Inspect at least twice per season and replace as necessary
Daily driving: Inspect annually or every 6,000 miles, and replace as needed

Ensure your BMW’s fuel system stays in top shape with the Replacement Fuel Filter Element - 10 Micron | Precision Raceworks, designed to deliver consistent fuel flow and protect your high-performance engine.

Show More Show Less

AN6 Male Flare/ORB To 5/16" (7.89mm) Female Quick Connect

T#:38094309

Part#: 201-0274

Ships in 6 Business Days

$ 24.99 USD

Add to Wish List

Qty

$ 24.99 USD

Add to Wish List

The Precision Raceworks AN6 Male Flare/ORB to 5/16" (7.89mm) Female Quick Connect is a premium component designed for fluid or fuel systems. The AN6 male flare/ORB fitting ensures a secure connection, while the 5/16" (7.89mm) female quick-connect fitting allows for fast, tool-free disconnection and reconnection. This setup guarantees a reliable, leak-proof seal, ideal for high-performance systems. Would you like assistance sourcing this fitting or other Precision Raceworks components?

Show More Show Less

Precision Raceworks High Performance Fuel Pump Kit - Stage 2 - BMW E-...

T#:5215999

Part#: 601-0096

Ships in 9 Business Days

$ 519.99 USD

Add to Wish List

Qty

$ 519.99 USD

Add to Wish List

If you are looking to get more power out of your BMW, it's important not to forget your fueling system! Your low and high-pressure fuel pumps can only flow so much fuel, limiting power potential regardless of turbo size or other power adders, especially true when running ethanol blends. Bring your fuel system up to par with Precision Raceworks' E-Chassis High-Performance Fuel Pump Kits! Precision's low-pressure fuel pumps are designed to flow significantly more fuel than your BMW's stock system, ideal for customers who are upgrading their vehicles or plan to run blended fuel or E85 alone. Best of all, these pumps ship completely assembled and ready to install! New pump, new fuel filter, and new sending unit included! This is a true plug-and-play solution that anyone can install in their home garage and start taking advantage of the benefits right away. By design, a fuel pump such as this is ideal for daily driving and racing applications of all kinds. This system keeps the primary pump fully submerged in fuel regardless of tank level or the g-force the car is subjected to. Precision Raceworks' Stage 2 bucketed fuel pump kit includes a Walbro 450 (F90000274) fuel pump, capable of supporting up to 575whp on 93 octane pump gas or 500whp on 100% E85! Even better yet? No wires to cut or splice, nothing to assemble, 100% OEM quality, and drop-in ready. Included in the box New genuine OEM fuel pump bucket assembly (Pre-assembled with genuine Walbro 450 pump) Includes new fuel sending unit (fuel level sensor) New primary and secondary fuel filters Stage 2 Specifications: Horsepower Supported Pump Gas: ~575whp Horsepower Supported 100% E85: ~500whp Aftermarket EKP Required: No **Some European Spec vehicles may require the re-use of the top hat due to differences in emissions requirements.

Show More Show Less

Precision Raceworks High Performance Ignition Kit - Black Coils - BMW...

T#:38229094

Part#: 601-0108-1

Ships in 7 Business Days

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

Rid your BMW's N55 of misfires, sluggish throttle response, rough idle, and power loss with Precision Raceworks' High-Performance Ignition Kit! Precision Raceworks' ignition kit is designed to fit any vehicle with an N55 engine and offers the highest output of any kit on the market! Featuring 100% Plug-&-Play connections, low resistance 50ohm/ft proprietary plug wires, and design technology from Marine and Aerospace applications, these coils are guaranteed to output consistent high voltage and current for optimal ignition system performance and reliability. Every component in this kit meets or exceeds OEM quality and features premium seals for dust and water resistance. While coils do not directly increase horsepower, stock BMW coils can wear out quickly, resulting in underperforming voltage and current output. This often leads to weaker spark intensity and reduced power output. Due to the increased voltage and current output, many customers have seen as much as 20+ whp/wtq gained by switching to Precision Raceworks coils over all other coils on the market! By upgrading to Precision's Performance Ignition Kit, spark quality can be restored, and lost power regained often with the additional power beyond what other coils provide. No software tune is required for installation or operation, but if desired, coil output can be increased to 118mJ from most software tuning companies!

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW X Series E84 (2013-2015)

Sub-Categories

Fuel Filter Replacement Guidelines:

NGK Spark Plug - Set Of 4 (121200396642)

Fuel Filter Replacement Guidelines:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results