BMW Suspension Parts for BMW 3 Series E90 (2006-2011)

Bilstein has teamed up with Eibach to offer matched shock and spring packages. These Eibach springs are mated to a special set of Bilstein shocks to deliver a sporty and taut ride with as little impact on ride comfort as possible.

The Pro Kit uses an Eibach Pro Kit spring with Bilstein's Sport shocks and struts. Instead of taking parts from different manufacturers, Bilstein has tested the performance of the Eibach spring and tailored their shocks to be a true match for the new spring rate and ride height. This is known as a matched shock and spring and very few tuning companies take these extra steps. Eibach springs tend to be softer overall than most other aftermarket springs, which ensures the ride stays close to a stock comfort while still giving you a lowered stance and improved handling. 

Bilstein B12 Features: 

• Precise response and excellent driving performance
• Springs and shocks road tested and fine-tuned to complement one another
• Bilstein Monotube/Inverted gas pressure technology
• TUV certified
• Made In Germany
• Average Lowering of 25 to 40mm

Most cars don't need coil overs to improve their handling and bodyroll. For most drivers, simply replacing the shocks and springs with performance versions will meet their goals. If your shocks need replacing, and you felt the handling could be improved a little bit, this is an excellent performance suspension for you.

This item fits the following BMWs:
2006-2011 E90 BMW 325i 328i 330i - Sedan

These bushings replace the stock rubber bushings and offer a better driving feel, increased lifespan, and better wheel alignment.

Rubber bushing allow for a lot more movement and are more susceptible to wear and tear from spirited driving and harsh weather conditions. Polyurethane is much more resistant to wear and is stiffer, reducing the total amount of movement that would normally affect the alignment negatively.

After shocks and springs, sway bars make the biggest change in handling. Larger swaybars will reduce bodyroll and understeer. The car will corner flatter with the tire in better contact with the pavement. New urethane bushings are included.

This is a rear 15mm sway bar that is larger than the factory sway bar.

Tasked with keeping the vehicles rear end firmly mounted while absorbing noise, vibration, and harshness (NVH) factory rubber subframe bushings were engineered to provide a balance of control while keeping the ride quality soft and supple. As a factory bushings age, they become brittle and begin to harden. When this happens the bushing will actually shrink and allow excess play, or movement in the subframe. This is typically felt by a sudden jerk or "thunking" noise under acceleration and is a leading cause of "sloppy" or "loose" suspension feel. These poly inserts provide the inherent benefit of stiffness, which translates body forces much more directly. This means steering and acceleration inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver. 

Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Engineered to perform, Powerflex performance polyurethane bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

Looking to improve the handling characteristics of your BMW? The 034Motorsport Dynamic+ sway bar kit aims to do exactly that. These sway bars feature 3-way (front) and 2-way (rear) adjustability for infinite tailoring to suit your preferred stiffness. Constructed of high-grade spring steel, these bars are built with rigidity and durability in mind. Together, these front and rear sway bars provide reduced body roll, increased turn-in, reduced understeer, and enhanced steering feel.

Rear Sway Bar:

2-Way Adjustable Soft: 21% Increased Sway Bar Rate Over M3 Stiff: 35% Increased Sway Bar Rate Over M3 22mm Diameter One-Piece Design with Solid Spring Steel Construction Black Powder Coating for Durability and Stealthy Appearance Reduces Rear Body Roll Reduces Understeer Improves Turn-In Rotation when Cornering

Tasked with keeping the vehicles rear end firmly mounted while absorbing noise, vibration, and harshness (NVH) factory rubber subframe bushings were engineered to provide a balance of control while keeping the ride quality soft and supple. As a factory bushings age, they become brittle and begin to harden. When this happens the bushing will actually shrink and allow excess play, or movement in the subframe. This is typically felt by a sudden jerk or "thunking" noise under acceleration and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushings with full polyurethane this play is eliminated since the subframe is being held in place by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering and acceleration inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver. 

Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

This part fits the following BMWs:
2008 - 2013 E82 1 Series Coupe 128i 135i 135is 1M Coupe
2007- 2013 E88 1 Series Convertible 128i 135i
2006 - 2009 E91 325xi 328i 328xi
2009 - 2011 E91 328i 328xi 

 

Sway bars are an essential upgrade when trying to get the best handling capabilities out of your BMW. Stock sway bars allow for too much play and excessive body roll, not keeping the wheels as firmly planted as they should be. Whiteline offers their performance sway bar kits that are designed to improve your BMW's handling characteristics and come with upgraded polyurethane bushings as well.

This Whiteline 27mm sway bar gives you more grip, better handling, and better outright performance. Sway bar upgrades are one of the best dollar-for-dollar investments you can make, improving your BMW's handling dynamics without affecting the comfort or ride quality.

This part fits the following BMWs:
2008 - 2013 E82 1 Series Coupe 128i 135i 135is 1M Coupe
2007- 2013 E88 1 Series Convertible 128i 135i
2006 - 2008 E90 323i 325i 325xi 328i 328xi 330i 330xi 335i 335xi
2009-2012 E90 323i 323i 328i 328xi 335d 335i 335i xDrive 335xi
2006 - 2009 E91 325xi 328i 328xi
2009 - 2011 E91 328i 328xi 
2007 - 2013 E92 328i 328xi 335i 335xi
2007 - 2013 E93 328i 335i

Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.

Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

These SPL Parts adjustable rear toe arms replace OEM part number 33322283549

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

When lowering your vehicle, toe alignment is thrown off. These SPL adjustable toe arms offer a wide range of toe adjustment and are a significant improvement over stock, eliminating suspension deflection and increasing handling response thanks to the FK Bushings rod ends that are Teflon lined.

Technical Specifications:

• Gundrilled 2024 Aluminum Links to reduce unsprung weight
• 6061 Aluminum Clamps and Heim Joint Spacers
• Titanium Socket Head Cap Screws
• Rotating clamp design allows for easy access to lock down your alignment settings
• Low friction 3 piece Teflon lined FK Heim joints/rod ends made in Connecticut
• Made in the USA!

Fits the following BMWs:
2006-2013 E9X BMW M3
2008-2013 E8X BMW 1 M

Koni suspension has taken their long running FSD (Frequency Selective Dampening) Technology and improved upon it to create their new Special Active suspension package. Improving handling while also improving the comfort of your BMW's ride, Special Active shocks and struts prove they are a top contender in the replacement suspension market.

Koni's Special Active dampers adapt to the continuous imperfect road conditions in order to provide you with a more responsive and smoother ride. Thanks to multiple generations of suspension expertise, these shocks and struts rival expensive ride control systems of newer vehicles but at a cost that is significantly lower and a capability to be retrofitted into existing vehicles.

Designed by Koni for the vehicle's original stock ride height, these are not intended to be used with lowering springs and will perform best when paired with stock springs.

Koni Special Active Features:

• KONI’s latest generation of Frequency Selective Damping Technology
•  Improves safety and road holding
•  Technology proven on over 1.5 million factory equipped vehicles
•  Secure and stable feeling for spirited driving
•  Unrivaled aftermarket solution can be fitted to most new and older cars
•  Driving refinement for cars, trucks, SUVs, etc.
•  Technology that rivals expensive Original Equipment electronic systems
•  Performance for driver and comfort for passengers in one

Activate your Koni Rebate!

Fits the following BMWs:
2006-2011 E9X BMW RWD Non-M

BMW E9X M3 Supplementary Ride Quality & Handling Kit enhances the performance of your BMW by working in conjunction with Dinan performance springs. This kit is designed to improve handling while maintaining superior ride quality. It includes:

• Progressive-Rate Bump Stops: Optimizes suspension travel, preventing bottoming out and binding.
• Enhanced Mechanical Grip: Improves spring rate for better handling.
• Maximized Suspension Travel: Allows for more effective use of suspension capabilities.
• Prevents Bottoming Out and Binding: Ensures a smooth and controlled driving experience.
• All Hardware Included: Simplifies installation with included uprated strut mounts.
• Dinan Badge Points: Earns 1 point toward the Dinan badge.

For over 35 years, Dinan has been a leading name in BMW tuning, known for balancing enhanced performance with the original driving character of BMW vehicles. The Dinan kit comes with a four-year, 50,000-mile warranty, reflecting their commitment to quality and durability.

Megan Racing Adjustable Control Arms for Enhanced Handling

Upgrade your vehicle's handling with Megan Racing's adjustable control arms, addressing the limitations of factory camber adjustments. Factory settings often fall short in optimizing handling and tire wear, especially for lowered vehicles, requiring more adjustment than the standard eccentric bolt can provide. Megan Racing's reinforced suspension arms offer a solution, delivering enhanced strength and adjustability for competition vehicles.

Key Features:

• Megan Racing's adjustable control arms optimize handling for lowered cars
• Constructed from high-strength steel alloys for durability and lightweight design
• Track-tested for quality and performance in road race, autocross, and drift events

Specifications:

• Durable construction suitable for daily driving and track use
• Maximum Arm Length: 17 7/16"
• Minimum Arm Length: 15 13/16"