When replacing your worn out brakes, the market is flooded with performance options. If your BMW doesn't see track time, it's not very practical. Performance pads and rotors tend to result in a lack of bite at low braking temperatures and cause excessive noise in daily driven vehicles that becomes irritating. BMW brakes from the factory are perfectly suited for trips around town, across the country, and even the occasional spirited driving session, delivering smooth, quiet, and long lasting performance. 

Included in this E9X BMW brake package are all of the OEM equivalent components needed to replace your Rear brakes with comfort, reliability, and optimal lifespan in mind.

Brake components in this kit:

• Akebono Euro Rear Brake Pads
• Zimmerman Rear Rotors
• New Rear Wear Sensors
• Brand New Stainless Steel Set Screws
• Syl-Glide Silicone Brake Lubricant 

Fits the following BMWs:
2006+ E9X BMW 325i 328i

As an E9X M3 owner, do you feel short-changed in the braking department? The next gen M3/M4 got serious Brembo calipers. With a special bracket the front 6-piston calipers can fit the E9X M3 for a bolt-on caliper and rotor upgrade. The rotors in this kit are 382x36mm - 22mm larger and 6mm thicker than the stock E9X rotor (and slightly bigger than the stock M3/M4 disc). The larger front rotors will help manage and dissipate heat better than the smaller stock rotors. And a larger rotor and caliper mean stronger brakes. Testing has shown the brake bias is very close to a stock E9X M3. Upgraded rear rotors are also included to work with the stock rear calipers. These are the blue M3/M4 calipers with the ///M logo.

Front brake specs:

• 382x36mm 2-piece floating rotors - 50% larger surface area and more cooling vanes
• 6-piston Brembo caliper (blue)
• Custom brake caliper bracket to fit the E9X M3 hub
• Multiple pad options
• Stainless brake lines

Rear brake specs:

• 350x24 2-piece floating rotors (same size as stock)
• re-use stock calipers
• Multiple pad options
• Stainless brake lines

Wheel fitment notes:

• 19" wheels required 
• Wheel spacers may also be required depending on wheel design
• Slight bending of front dust shields is requried

*Will not ZCP Wheels* 

This brake package for the BMW E90/E92/E93 335i comes with everything you need to perform a major brake overhaul --

Rotor Options:

• OEM rotors
• Turner cross-drilled sport rotors
• Turner slotted performance rotors
• Turner drilled+slotted sport rotors
• ECS 2-piece floating rotors

Pad Options:

• OEM street pads
• Street performance sport pads
• Street dust-less pads
• race pads

Additional items included:

• Rotor retaining screws
• Front and rear pad wear sensors
• Brake fluid

Braided stainless steel brake lines are optional and recommended for track or aggressive street use.

Our brake package uses the same replacement parts from the same manufacturers as BMW dealers use to service your car. The big difference is that we're able to offer these parts for a substantial savings from the dealer markup price. As an independent company we're able to buy our parts from multiple OEM suppliers whereas BMW dealers must buy their parts from BMW. We're able to shop from different vendors which gets you a better price while still maintaining original quality. You don't have to pay high prices at the dealer to get the same quality and performance.

In some cases, we offer performance alternatives to the OEM items. For an enthusiastic BMW owner, the standard BMW part may be inadequate and we offer an upgraded part, based on our 20+ years of BMW tuning experience. We seek out high quality suppliers and designs that we would want on our own vehicles. Many times performance parts will fix a design flaw with the original BMW part, improving your performance at the same time.

Brake Package FAQ
Brake Pad Buying Guide
Brake Rotor Buying Guide

Applications:
2007-2011 E90 335i sedan
2007-2013 E92 335i coupe
2007-2013 E93 335i convertible

F30 M Performance brakes for your E9X 325/328/330/335! This kit uses the factory M Performance front and rear Brembo multi-piston calipers and rotors for a bolt on braking upgrade. Everything comes complete -

The ECS M Performance Big Brake Kit includes:

• Orange 4 Piston Brembo front calipers from the F3X M Performance brake kit 
• Orange 2 Piston Brembo rear calipers from the F3X M Performance brake kit (custom machined, with brackets)
• Front 370x30mm ECS 2-piece rotors
• Rear 350x24mm ECS 2-piece rotors
• ECS Exact-Fit Stainless Steel Brake Lines
• Genuine BMW front & rear brake pad set (use any M Performance - fitment brake pad)
• Class 12.9 mounting hardware, brake fluid, pad wear sensors

Performance:

• Bias - 63.3% front, 36.7% rear – optimally balanced for the e9x chassis
• Brake torque – 4% increase results in more responsive braking system
• Pedal feel – firmer pedal feel for improved modulation
• Improved cooling & heat management - brake deeper, harder, with less fade

More on ECS Exact-Fit Stainless Steel Brake Lines (the same tried-and-true style you've probably been running for years):

• Independently tested for DOT compliance to the FMVSS 571.106 standard for brake lines
• Volumetric expansion verified at 17% of the maximum allowable for low expansion hose at 1500 psi, with a burst strength of nearly 2.5x the required minimum.
• Tensile pull strength of nearly double the minimum requirement. Whip resistance of over double the required test limit. Passes 24hr salt spray test with flying colors 24hr salt spray test - no white or red rust.
• Exceptional resistance to expansion under extreme line pressure results in improved pedal feel and braking response. Each line quality inspected and pressure tested to 3000psi.

More on ECS 2 piece Cross-Drilled/Slotted Rotors: 

• Weight savings: save 2 lbs per axle versus the genuine BMW rotor.
• Increased thermal capacity and Improved cooling:  
  • Heat convection (due to air flow) is considered the most important mode of heat dissipation in rotor design. The key to this is adequate air flow through the rotor.
  • ECS 2-Piece rotors feature side-specific directionally curved vanes which pump air through the rotor at a higher velocity, leading to consistent, rapid cooling on both sides equally.   
  • The air velocity in curved vane rotors is higher than pillar-post rotors and straight vane rotors, and as such curved vane rotors have been shown to cool more effectively.
• Manufacturing quality: Manufactured exclusively for ECS Tuning in an ISO 9001 certified facility
• Testing:  ECS 2-piece rotors have been subjected to thousands of miles of hard street use and to the elements (including snow and salt) for years. They have also been subjected to scientific brutal stress testing on the track and brake dyno, performing countless high-speed stops in quick succession.  We have measured stopping distances and elevated rotor temperatures of over 1000*F for long sustained periods (to the point of rotor bluing and catching brake pads on fire), as well as subjecting rotors to careful post-test inspection for signs of irregular wear, warping, stress cracking, or any other signs of failure.

• ECS rotors have proven themselves to be robust, demonstrating excellent wear characteristics, no warping, no thermal stress cracking, no signs of hot spots and minimal pad glazing.​

This is a direct fit to all non-M E9X and comes with a lot more braking power than standard (especially on non-335 models). You can use any F30 brake pad with these (OE BMW come standard) so there are a lot of street and track pad options. The rear calipers have been especially modified to work with the ECS caliper bracket.

Requires 18" wheels and wheel spacers may be required depending on wheel spoke design.

These 2-piece floating rotors help dissipate heat better than a standard cast iron rotor and are also lighter for less unsprung weight. Managing heat in the brake system is vital to braking performance, especially on the track or when driven hard. It's why your brake rotors have internal vanes that vent heat as the rotor spins. These 2-piece ECS rotors feature an outer cast iron friction surface ring that is separate from the aluminum center hat. This allows better airflow through the vanes and for the friction ring can expand as it gets hot. The rotors are also cross-drilled for better ventilation and slotted to improve brake pad performance.

ECS 2-Piece Rotors feature:

• Aluminum hats for light weight
• Heat-treated cast iron friction rings
• 2-piece assembly improves brake cooling
• Anti-corrosion coating on non-friction surfaces and hard anodizing on rotor hat

These are the same size as the stock rotors so your stock caliper and mounting bracket will fit and there will be no clearance issues with your wheels or to other components. Stainless steel rotor retaining screws are included. You can use these with any brake pad.

Price is for the pair of brake rotors.

This item fits the following BMWs:
2011 E82 E88 BMW 1M Coupe
2008-2013 E90 E92 E93 BMW M3 Sedan, Coupe, Convertible

These 2-piece floating rotors help dissipate heat better than a standard cast iron rotor and are also lighter for less unsprung weight. Managing heat in the brake system is vital to braking performance, especially on the track or when driven hard. It's why your brake rotors have internal vanes that vent heat as the rotor spins. These 2-piece ECS rotors feature an outer cast iron friction surface ring that is separate from the aluminum center hat. This allows better airflow through the vanes and for the friction ring can expand as it gets hot. The rotors are also cross-drilled for better ventilation and slotted to improve brake pad performance.

ECS 2-Piece Rotors feature:

• Aluminum hats for light weight
• Heat-treated cast iron friction rings
• 2-piece assembly improves brake cooling
• Anti-corrosion coating on non-friction surfaces and hard anodizing on rotor hat

These are the same size as the stock rotors so your stock caliper and mounting bracket will fit and there will be no clearance issues with your wheels or to other components. Stainless steel rotor retaining screws are included. You can use these with any brake pad.

Price is for the pair of brake rotors.

This item fits the following BMWs:
2006-2011 E90 BMW 335d 335i 335xi - Sedan
2007-2013 E92 BMW 335i 335is 335xi - Coupe
2007-2013 E93 BMW 335i 335is - Convertible
2012-2015 E84 BMW X1 xDrive35i