Genuine BMW for BMW 3 Series E91 (2006-2012)

Turner recommends replacing these bolts when replacing your starter as these bolts are aluminum and torque to yield - making them one time use bolts.

We recommend the Bosch replacement starter to get your vehicle back on the road.

This is the sensor / sending unit that notifies the computer if your coolant level is low. When this fails, it can give a false indication of low coolant -- or worse, not inform you of a low coolant situation which could potential cause overheating. (Note: This sensor is also found in the windshield washer container, to alert the computer when you are low on washer fluid)

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

This sensor also serves as the washer fluid level sensor on many models.

This fluid level sensor is found on the following BMWs:
1999-2005 E46 3 Series - 323i, 323Ci, 328i, 328Ci, 325i, 325ix, 325Ci, 330i, 330ix, 330Ci
2001-2006 E46 M3
2000-2003 E39 M5 Coolant Level Sensor only
2006-newer E90/E92 3 Series - 325i, 325xi, 328i, 328xi, 330i, 330xi, 335i, 335xi M3
2004-2009 E60 5 Series - 525i, 525xi, 528i, 528xi, 530i, 530xi, 545i, 550i, M5
2004-2009 E63/E64 6 Series - 645Ci, 650i, M6
2002-2009 E65/E66 7 Series - 745i, 745Li, 750i, 750Li, 760i, Alpina B7
2004-2009 X3 SAV - X3 2.5i, X3 3.0i, X3 3.0si
2000-2006 E53 X5 X5 3.0i X5 4.4i X5 4.6is X5 4.8is
2007+ E70 X5 X5 3.0si X5 4.8i X5 xDrive30i X5 xDrive48i X5M
2007+ E71 X6 X6 xDrive35i X6 xDrive50i X6M
2003-2009 Z4 Roadster/Coupe - Z4 2.5i, Z4 3.0i, Z4 3.0xi, MZ4 Roadster & Coupe
2000-2003 E52 Z8 Z8 Roadster - Coolant Level Sensor only
 

Not only will this kit stop most E90 oil leaks, it's the perfect addition for ignition coil or spark plug replacement! Oil leaks - and the damage they can cause - seem to be the worst annoyances on these cars. The biggest source of an oil leak is from the valve cover, followed by the oil filter housing, Valvetronic seal, camshaft seals, and the eccentric shaft sensor seal. Once the oil leaks, and if ignored for an extended time, the oil will contaminate vital electrical sensors. This is especially the case with ignition coils and also the eccentric shaft sensor on the Valvetronic shaft at the top of the cylinder head. During any ignition coil and spark plug replacement take a close look inside for any oil pooling at the bottom. We have been seeing valve cover oil leaks as soon as 40,000 miles. We look for oil leaks on every E90 that comes into our shop.

We have put together this package of valve cover gaskets and other related gaskets and seals for you to fully overhaul the N52 valve cover and put a stop to those pesky oil leaks. This package has the replacement parts for N52 engines built up to 10/2006 and includes:
 

• 11127581215 - N52 valve cover gasket set
• 11120409288 - N52 aluminum valve cover bolts (1-time use only, not re-usable)
• 11377516302 - N52 Valvetronic gasket
• 11127528242 - N52 eccentric shaft sensor seal

These are all Genuien BMW parts. Replacement of these gaskets and seals is straight-forward but a long process. BMW dealers typically charge for over eight hours of labor. If you have replaced spark plugs before you should be capable of this repair. In addition, there are several other parts to replace while you're in the vicinity: camshaft sensor o-rings, oil filter housing profile gasket, VAN0S solenoids, and the eccentric shaft sensor. These other parts, except the eccentric shaft sensor (see below), are replaceable without removing the valve cover but are more easily accessed during the valve cover work.

Eccentric Shaft Sensor: This is the position sensor that relays the eccentric shaft's position back to the DME. It's located at the front of the engine and is only accessible with the valve cover off. Over time the seal around the sensor comes loose and oil is allowed to blow out of the cam cover and it eventually finds its way into the sensor (which will eventually fail). Without a functioning sensor your E90 can experience poor running, hesitation, poor performance, jerky shifts, and sluggish response. It's easy to check and see if oil has accumulated inside the sensor: unbolt the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside or even around the sensor itself, plan on replacing this sensor during your next ignition coil, spark plug, and/or valve cover gasket work.

This valve cover kit fits the following BMWs:
2006 E90 BMW 325i 325xi 330i 330xi - Sedan
2006 E91 BMW 325xi - Wagon
2006 E60 BMW 525i 525xi 530i 530xi
2006-10/2006 E85 BMW Z4 3.0i Z4 3.0si

Resolve BMW Cupholder Issues with Replacement Dashboard Cupholder Set

Resolve the common issue of failing BMW cupholders with this replacement dashboard cupholder set. Despite improvements in newer models, BMW cupholders can still encounter problems such as broken mounts or difficulties popping in and out.

This replacement set offers several benefits:

• Addresses issues with broken mounts or malfunctioning cupholder mechanisms.
• Restores proper functionality to your BMW's dashboard cupholders.
• Designed as a direct replacement for seamless installation.
• Ensures reliable performance for an essential interior component of your BMW.

Upgrade and restore the functionality of your BMW's cupholders with this reliable replacement dashboard cupholder set.

Looking to change your oil and only want the best? Genuine BMW oil service kits feature the exact oil and components BMW intended for use in your in your premium vehicle when being serviced at the dealership. This ensures your vehicle continues to perform flawlessly, running longer and cleaner!

This kit includes:

• OEM oil filter kit
• Oil drain plug with gasket
• 7 quarts of BMW synthetic engine oil