Select Vehicle
BMW
Mini
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
BMW E8X E9X Turbo Inlet Flange Adapter Kit 1.75" To 2" by Turner Motorsport is designed to facilitate a seamless upgrade for your turbo system. This precision adapter kit allows BMW E9X and E8X owners to run 2" relocated inlets on stock turbos with confidence, ensuring a secure fit without the risk of the inlets slipping off.
All of the tuning in the world is only as good as the weakest link. More boost in your 135/335 is great! But you will soon learn that some of the factory hardware is not up to the task of handling that extra pressure. One of the first things to fail and cause a boost leak are the factory boost diverter valves. This allows boost to "leak" out of the intake stream and a loss of power from the engine. This ECS Tuning chargepipe upgrade includes a blow-off valve in place of the factory diverter valves. The BOV is higher quality than the diverter valves and will exit intake air to the outside instead of putting it back through the turbo system (which will reduce strain on the turbos). This aluminum chargepipe is also much more robust than the stock plastic factory pipe and the connection to the throttle body is stronger, eliminating another failure point of the stock pipe.
Built-in 1/8" NPT ports allow you to run an additional methanol injection kit (bungs included if you don't want use the ports).
This is a complete kit that includes everything you need to replace the factory chargepipe and diverter valves -
powedercoat chargepipe ECS Tuning blow-off valve Includes three interchangeable BOV springs, allowing you to tailor venting function to your existing modifications. 1.9 (For use with factory software) 2.0 (Pre-installed in the SQV BOV - suitable for stock or "Stage One" software) 2.2 (Suitable for "Stage Two" software) vacuum plugs for the stock diverter valve hoses silicone hose connection to intercooler piping all hardware and hose clamps with instructions
This alloy hard pipe fits to the throttle body and incorporates our high flow Blow off valve. This new valve fresh from our R&D department is the largest displacement valve that Forge have ever made ! Featuring a 50mm (2”) aluminium piston so that there are no issues with split diaphragms, we have not found the power handling limits of this valve yet ! The piston uses heat stabilised viton o-rings and high temperature Mobil 1 grease to ensure a long life with minimal wear and very long service intervals.
All parts are included in the kit, for your installation, along with comprehensive instructions.
This product fits the following BMWs:
2008 - 2013 E82 135i
2007 - 2013 E9x 335i
This aftermarket charge pipe from COBB Tuning is perfect for someone who is looking for a charge pipe that offers increased air flow and improved reliability.
Made from 3" mandrel bent aluminum piping, this Charge Pipe replaces the weaker stock plastic charge pipe (BMW Part # 13717615026) that is brittle and prone to cracking and/or failing under high boost pressures.
**You may need to source a new O-Ring (P/N 13717568031) and possibly a new C-Clip if yours are missing or damaged as they are not included with this kit.
If you are looking to replace your stock chargepipe for better reliability and higher performance, the Burger Motorsports designed and Phoenix Racing built Performance Aluminum Chargepipe is an excellent choice! This aluminum chargepipe is significantly stronger than the stock plastic pipe and the powder coated aluminum looks great and will resist any corrosion. Plus, this chargepipe features a 3 inch design for optimal flow at all RPMs, prevent restriction that would normally be seen with the stock pipe. This is perfect for someone looking to upgrade a stock or tuned N54!
Specs and Features:
O-rings and retaining clip must be reused from the original pipe or purchased new for proper installation.
If you are looking to replace your stock chargepipe for better reliability and higher performance, the Burger Motorsports designed and Phoenix Racing built Performance Aluminum Chargepipe is an excellent choice! This aluminum chargepipe is significantly stronger than the stock plastic pipe and the powder coated aluminum looks great and will resist any corrosion. Plus, this chargepipe features a 3 inch design for optimal flow at all RPMs, prevent restriction that would normally be seen with the stock pipe.
In addition, this pipe also includes a Tial BOV flange for easy installation of a Tial BOV without any modifications needed to the chargepipe. This is perfect for someone looking to upgrade a tuned or heavily modified N54!
Specs and Features:
O-rings and retaining clip must be reused from the original pipe or purchased new for proper installation.
VTT is proud to offer the very best Cold Side charge pipe solution for the BMW E Series N54 platform. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipe rated at over 200 psi. They are molded for the perfect fit in your engine bay, while not sacrificing anything in the way of flow or size. They also completely isolate your charge air from any additional heat soak coming in from the engine or ambient heat. Another huge benefit is only TWO connections which are barbed and has many small ridges which dig into the silicone so it’s impossible for the pipe to blow off.
This N54 pipe has a flange installed to support a Turbosmart BOV.
This is the EASIEST N54 charge pipe on the market to install hands down. Install takes about half an hour even if you are inexperienced with working on your own car, can take as little as 15-20 minutes if you have had it apart a few times.
The kit includes:
VTT Cold Side Silicone Charge pipe
2 VTT Branded CNC adapters to mount the map sensor, and a methanol bung
1 VTT Branded CNC adapters for the TB inlet
2 VTT branded T-Bolt Clamps
1 1/8 NPT port is included in the charge pipe for methanol
Refresh and upgrade your front intercooler to ensure you are supplying your engine with the maximum amount of airflow. With the added charge pipe and BOV kit you can drive confidently knowing the plastic charge pipe is replaced with a much stronger metal alternative with added blow off valve for a full performance and sound upgrade!
OEM+ Upgraded Front Mount Intercooler:
Upgrade your N54/N55 performance effortlessly with this "OEM+" Intercooler from ECS Tuning! This premium intercooler is engineered to deliver superior cooling efficiency and increased horsepower without the hassle of extensive bumper/core support modifications.
Key Features:
Enhanced Core Depth: Featuring a robust aluminum bar and plate core, this intercooler ensures optimal heat dissipation for peak performance.
Durable Construction: TIG-welded cast aluminum end tanks provide unmatched durability, replacing the factory's plastic components.
Perfect Fitment: Designed to fit just like the OEM unit, it requires no additional brackets or modifications to the bumper or core support.
Compatibility: Works seamlessly with OE charge pipes and pipe connectors for easy installation.
Benefits:
Improved Cooling Efficiency: Significantly lowers intercooler outlet temperatures, ensuring your engine runs cooler and more efficiently.
Increased Durability: Aluminum end tanks offer enhanced durability and longevity compared to factory plastic construction.
Hassle-Free Installation: No need for trimming the front bumper or modifying the radiator support, making installation straightforward.
Whether you're after increased performance or an OEM purist, the ECS Tuning OEM+ Intercooler is the perfect upgrade for your BMW. Enjoy the benefits of increased horsepower and lower temperatures with an easy, hassle-free installation.
N54 Chargepipe and BOV Kit:
All of the tuning in the world is only as good as the weakest link. More boost in your 135/335 is great! But you will soon learn that some of the factory hardware is not up to the task of handling that extra pressure. One of the first things to fail and cause a boost leak are the factory boost diverter valves. This allows boost to "leak" out of the intake stream and a loss of power from the engine. This ECS Tuning chargepipe upgrade includes a blow-off valve in place of the factory diverter valves. The BOV is higher quality than the diverter valves and will exit intake air to the outside instead of putting it back through the turbo system (which will reduce strain on the turbos). This aluminum chargepipe is also much more robust than the stock plastic factory pipe and the connection to the throttle body is stronger, eliminating another failure point of the stock pipe.
Built-in 1/8" NPT ports allow you to run an additional methanol injection kit (bungs included if you don't want use the ports).
This is a complete kit that includes everything you need to replace the factory chargepipe and diverter valves -
powedercoat chargepipe
ECS Tuning blow-off valve
multiple BOV springs to suit your vacuum/boost needs
vacuum plugs for the stock diverter valve hoses
silicone hose connection to intercooler piping
all hardware and hose clamps with instructions