BMW Drivetrain Parts for BMW 3 Series E93 (2007-2013)

When installing a new clutch, it is important to replace old hardware and common wear items. This ensures both a smooth and reliable installation. This also allows you to perform maintenance while everything is apart as opposed to a needing to make future repairs when everything is back together.

Included in this kit:

• Flywheel bolts
• Bolts bell housing, one time use!
• All hardware to re-mount the driveshaft
• Pilot Bearing
• Clutch fork pivot pin
• Clutch alignment tool
• Metal Guibo
• Center support bearing 

Fits the following BMWs:
E9X BMW 335i/is N54 N55

A sloppy shifter can make your driving experience miserable. Luckily these Genuine BMW shifter rebuild kits are available to restore the crisp feel of a brand new shifter. This kit includes all of the Genuine BMW components that normally wear down and cause issues such as the bushings, clips, and dowel pin.

See all of the included components below!

GKN is a global company specializing in meeting the needs of the growing automotive industry. Every time you travel by road or air almost anywhere in the world it is likely that GKN is helping you on your way. Designing, manufacturing and service systems and components for original equipment manufacturers, GKN is also competitive in the automotive aftermarket.

Continuously evolving, pioneering new technologies and reinventing existing ones, GKN is always striving to better themselves in everything they do.

Drive line slop is often caused by faulty engine and transmission mounts. This can result in knocking noises under heavy acceleration, excessive vibration, and a less responsive feel in power. These OEM Lemforder and Corteco mounts are perfect to eliminate these problems and provide long lasting reliability.

Included in this kit:

• OEM Corteco Engine Mount (x2)
• OEM Lemforder Transmission Mount (x2)
• New Installation Hardware

GKN is a global company specializing in meeting the needs of the growing automotive industry. Every time you travel by road or air almost anywhere in the world it is likely that GKN is helping you on your way. Designing, manufacturing and service systems and components for original equipment manufacturers, GKN is also competitive in the automotive aftermarket.

Continuously evolving, pioneering new technologies and reinventing existing ones, GKN is always striving to better themselves in everything they do.

Looking to upgrade your clutch disc? This Sachs Performance clutch disc is a great option. Allowing for higher torque and horsepower, this disc is perfect for aggressive track applications such as endurance racing, clubsport, autocross, hill climbing and 1/4 mile racing.

Sachs Performance is the racing and performance oriented selection of high quality parts from Sachs and ZF Engineering. Supplying countless brands with OE parts and offering one of the widest selection of OEM replacement parts, they are known for their exceptionally high quality products. You can purchase these performance parts with confidence, knowing they will resist heavy wear and tear for much longer than most other aftermarket options.

A sloppy shifter can make your driving experience miserable. Luckily these Genuine BMW shifter rebuild kits are available to restore the crisp feel of a brand new shifter. This kit includes all of the Genuine BMW components that normally wear down and cause issues such as the bushings, clips, and dowel pin.

See all of the included components below!

OEM LuK Clutch Kit includes Clutch Disc, Pressure Plate, and T/O Bearing. Call for applications not listed above. SACHS is the OEM supplier for BMW.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This is the stock twin mass flywheel for early N54 engines in the E82 135i, E9X 335i/xi, and E60 535i/xi (flywheel uses 8 mounting bolts). It's manufactured by OEM Shaeffler (LuK). Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008-1/2009 E82 BMW 135i
2007-1/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-1/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-1/2009 E93 BMW 335i - Convertible
2007-1/2009 E60 BMW 535i 535xi 535i xDrive

This is the stock twin mass flywheel for the N54 engine in later E82 135i, E9X 335i, E60 535i, and Z4 35i (cars with 6-bolt mounting hub). It's manufactured by OEM supplier LuK. Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

Tip: DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed on the flywheel hub.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

This item fits the following BMWs:
1/2009-2010 E82 BMW 135i
1/2009-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
1/2009-2010 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
1/2009-2010 E93 BMW 335i - Convertible
1/2009-2010 E60 BMW 535i 535xi 535i xDrive