BMW Engine Parts for BMW 7 Series F02 (2009+)

If your car won't turn over, there is a good chance your starter is shot. Bosch's OEM starter is a high quality replacement that will give you peace of mind thanks to its long life-span. OEM replacement for the original BMW part # 12411312104 and 12411312130. This is a NEW, not used, component with no included core charge!

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

We recommend replacing hardware when doing your starter, since the bolts are aluminum and threads become stretched: Genuine BMW aluminum starter hardware set 12410392577 

Used on a wide variety of models with the BMW N52, N54, and N55 engines, including: E9X, F01/02, F07/10, E8X, E70, E60/61, F25, F30, and Z4.

The VANOS system on your N51, N52, and N54 engine controls the valve timing inside the engine. The system is hydraulically operated based on instructions from the engine computer. It's very complex and BMW has not yet perfected the system. The VAN0S solenoid is the actuator that takes instruction from the ECU and activates the VANOS unit on the front of the engine. When the solenoid is failing (or failed) you can end up with a rough running engine, misfires, bad fuel economy, lack of power, and more. It should trigger multiple fault codes and a check engine light for misfires, camshaft control, VAN0S solenoid, boost pressure control, and maybe others. It's important to thoroughly troubleshoot fault codes but VAN0S solenoids are a known issue with these engines.

The VANOS solenoids are located on the front of the engine and may be replaced without removing many other components. In some cases, you may be able to remove the suspect one, clean it, reinstall, and reset your fault codes. If your fault codes come back it's a strong indication that a replacement is required. Or you can buy the new solenoid and replace instead of doing the work twice.

VANOS solenoid for the intake and exhaust are the same part number. Order 2 if you want to replace them both.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

We recommend replacing the solenoid sealing gaskets as well when replacing the solenoid. You can find these under T#363393

This item fits the following BMWs:
2008-2012 E82 BMW 128i 1M Coupe
2008-2010 E82 BMW 135i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335is - Sedan
2006-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335is - Coupe
2007-2010 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2007-2010 E93 BMW 335i - Convertible
2006-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive
2011 F10 BMW 528i
2006-2010 E83 BMW X3 3.0i X3 3.0si
2007-2013 E70 BMW X5 3.0si
2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009-2011 Z4 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

BMW Gray Filter Housing Cap - Blackline Performance Edition Oil is a premium upgrade designed to replace the standard OEM plastic oil filter housing cap. This high-quality billet aluminum cap enhances both the aesthetics and functionality of your BMW's engine.

• Durable Construction: Made from 6061 T6 aluminum with a hard anodized finish for superior strength and longevity.
• Improved Performance: Features better heat dissipation compared to the factory plastic cap, enhancing engine performance and reliability.
• Enhanced Aesthetics: Adds a sleek, high-performance look to your engine bay with 3D precision post-milled detailing and the G Insignia Oil Filter Cage Stabilizer.
• Easy Installation: CNC-formed hand grips and a 10mm Allen key maintenance port with a built-in scratch plate simplify the installation and maintenance process.
• Direct Replacement: Retains the factory oil filter stalk and is compatible with BMW S55 and most N series engines using BMW part 11427525334.
• Increased Longevity: Designed to increase the life span of your oil filter cap and provide a more reliable seal.