BMW Suspension Parts for BMW 2 Series F22 (2014+)

The Bilstein B14 PSS Suspension allows adjustable vehicle ride height without the expense of a fully adjustable damping system. This system features both coilover and standard mono-tube gas pressure shock or struts with performance level valving for application specific, progressive rate coil springs.
The product benefits at a glance:

• Threaded body adjustable range of 20 mm
• Lowering of approx. 30-50 mm at front and rear
• Road-tested and fine-tuned by BILSTEIN ride engineers, under extreme motorsports conditions
• Aluminum Spring plates and lock nuts
• Surface coating using Triple-C-Technology for long-lasting corrosion resistance
• Round threads for easy adjustment
• Quality sport springs made from highly durable material
• Gas pressure technology

BILSTEIN monotube technology, made in Germany

adj. -1.0"-1.75" / adj. -1.0"-1.75"

Not for cars with EDC

This coilover kit fits the following BMWs:
2013+ F30/34 BMW 320i 328i/d 335i 330i 340i - xDrive models
2014+ F32/36 BMW 428i 435i 430i 440i - xDrive Coupes/Grand Coupes

​

The ECS Coilover Line was designed with the "daily drivers" in mind! Focused on improving the performance and aesthetics of your vehicle without forgetting comfort. With 32 levels of available damping and height adjustments tailored to each car, ECS coilovers are right in that sweet spot of firm and compliant while giving you an aggressive look and vastly improved handling.

The ECS Tuning Performance Coilover System provides a sport-tuned, height, damping, and body adjustable suspension with substantial performance benefits using high-quality materials and coatings to replace your worn suspension, all while giving your vehicle that perfect ride height!

PERFORMANCE FEATURES:

32 levels of rebound damping adjustment
Includes adjustable front sway bar end links
Integrated camber plates for +/-1.5 degrees of adjustment to dial in your fitment and alignment
Lowering Adjustment of: 1.5" - 4"
Heat treated, progressive rate coil springs. 8k Front 10K Rear
Adjustable damping, monotube shocks/struts paired with optimized progressive rate coil springs gives your vehicle road-sticking grip with reduced body roll for exceptional confidence in your vehicle's handling. With your vehicle's new, lower ride height the center of gravity is now moved lower, further improving handling performance
Adjustable front bodies allow you to set the ride height while maintaining correct spring pre-load
Adjustable front and rear bodies allow the shock to operate in the correct valving range, regardless of ride height

PRODUCT DESIGN:

Strut and shock bodies finished with a durable gloss black powder coat for good looks and great longevity
Threaded portions are are zinc-coated for optimum corrosion protection against rain and salt (finish will vary between clear or black zinc coatings depending on availability)
Coil springs are powder-coated Reflex Silver Metallic finish for durability
Red anodized, billet aluminum spring seats with locking collars allow for quick, on the car, adjustability with the included spanner wrenches
Self-locking, zinc-coated flanged nuts used for shock & strut shaft pins
Anodized adjustable sway bar end links with heavy duty bushings
Zinc coated strut mount securing nuts included
Rear shock adjuster housings are black E-coated for durability
Zinc-coated lower spring perches
Integrated bump stops and dust boots

PRODUCT DEVELOPMENT

ECS Tuning Adjustable Damping Coilover Systems are developed in-house, tested and inspected by the Research & Development team in our Wadsworth, Ohio facility. The highest level of precision and quality through leading-edge product development technology and methods, ensuring the necessary long term product testing was performed on multiple test vehicles in the harshest conditions available.
Fitment:
For vehicles with 5 bolt upper strut mounts

F22, F23, F30, F32, F33, F34, F36

The ECS BMW Coilover line was designed with daily drivers in mind! The ECS engineer's focus was to improve the performance and look of the suspension, without forgoing ride comfort. Like many top-tier coilovers, these coilovers feel as smooth and comfortable as a stock setup, while also providing an aggressive look and vastly improved handling.

The ECS Performance Coilover System provides a sport-tuned, height, damping, and body adjustable suspension with substantial performance benefits using high-quality materials and coatings to replace your worn suspension, all while giving your vehicle that perfect ride height!

Spring Rates: 8kg/mm (front), 10kg/mm (rear)

PERFORMANCE FEATURES

32 levels of rebound damping adjustment Adjustable damping, monotube shocks/struts paired with optimized progressive rate coil springs give your vehicle road-sticking grip with reduced body roll for exceptional confidence in your vehicle's handling. With your vehicle's new, lower ride height the center of gravity is now moved lower, further improving handling performance Adjustable front bodies allow you to set the ride height while maintaining correct spring pre-load Adjustable front and rear bodies allow the shock to operate in the correct valving range, regardless of ride height PRODUCT DESIGN

Strut and shock bodies finished with a durable gloss black powder coat for good looks and great longevity Threaded portions are clear zinc-coated for optimum corrosion protection against rain and salt Coil springs are powder-coated Reflex Silver Metallic finish for durability Red anodized, billet aluminum lower spring seats with locking collars allow for quick, on-the-car, adjustability with the included spanner wrenches Integrated bump stops KIT CONTENTS

ECS Performance Adjustable Coilover System - F2X/F3X (3-Bolt) Front Suspension Installation Hardware Strut Mount Gasket - 31306869890 (2) Spindle Pinch Bolt - 31306798530 (2) Spindle Pinch Nut - 07119905032 (2) Tension Strut Bolt - 31106885777 (2) Control Arm Bolt - 31106797237 (2) Control Arm Nut - 33326760668 (2) Ball Joint Locking Nut - 33306787062 (4) CV Axle Bolt - 31206795249 (2) Rear Suspension Installation Hardware Shock to Control Arm Bolt - 07119907372 (2) Shock to Control Arm Nut - 33326760668 (2) Shock Mount Bolt - 07119907137 (6) Shock Mount Gasket - 33506866038 (2) Control Arm to Wheel Carrier Bolt - 33326762875 (2) Control Arm to Wheel Carrier Nut - 33306760349 (2)

The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

This coilover kit fits the following BMWs:
2014+ F22 BMW 228i M235i - Not for cars with EDC
2012+ F30 BMW 320i 328i 335i - Sedan - Not for cars with EDC
2013+ F32 BMW 428i 435i - Coupe - Not for cars with EDC

The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

Fits the Following Vehicles:
2012+ BMW F30 328i 328d 320i 335i 330e 330i 340i
2014+ BMW F32/F36 428i 435i 430i 440i
2014-2016 BMW F22 228i

Bilstein has teamed up with Eibach to offer matched shock and spring packages. These Eibach springs are mated to a special set of Bilstein shocks to deliver a sporty and taut ride with as little impact on ride comfort as possible.

The Pro Kit uses an Eibach Pro Kit spring with Bilstein's Sport shocks and struts. Instead of taking parts from different manufacturers, Bilstein has tested the performance of the Eibach spring and tailored their shocks to be a true match for the new spring rate and ride height. This is known as a matched shock and spring and very few tuning companies take these extra steps. Eibach springs tend to be softer overall than most other aftermarket springs, which ensures the ride stays close to a stock comfort while still giving you a lowered stance and improved handling. 

Bilstein B12 Features: 

• Precise response and excellent driving performance
• Springs and shocks road tested and fine-tuned to complement one another
• Bilstein Monotube/Inverted gas pressure technology
• TUV certified
• Made In Germany
• Average Lowering of 25 to 40mm

Most cars don't need coil overs to improve their handling and bodyroll. For most drivers, simply replacing the shocks and springs with performance versions will meet their goals. If your shocks need replacing, and you felt the handling could be improved a little bit, this is an excellent performance suspension for you.

This item fits the following BMWs: 
2014+ F22 BMW 228i 230i - Coupe

Our renowned TMS adjustable front sway bar / swaybar links for BMWs are now available in custom lengths, making them easy to order for any aftermarket or custom suspension setups. Simply measure for your ideal link length, and order the links with the best length range (below). Each sway bar link has a 10mm diameter mounting pin/stud, which is the typical factory/stock size for a universal fitment. These are sold by the pair, and each set includes two matching sway bar end links.

These end links offer the quiet operation and long life of "stock" BMW end links, but with the strength and adjustability of rod-end style sway bar links. These sway bar links can be used on a wide variety of BMWs and aftermarket BMW suspensions. When measuring, please consider that the length ranges of our Custom Adjustable end links are measured from the center to center on the end link mounting stud / pin, as shown in our diagram.

Note for E9X M3: the unique mounting on the M3 strut requires a set of our adapter seats (#TSU9912AF9). You can add them with your links from the menu below.
 

TMS Part#Center to Center (mm)Center to Center (inch)

TSU9912A35155.00mm - 170.00mm6.10" - 6.69"

TSU9912A40170.00mm - 185.00mm6.69" - 7.28"

TSU9912A45180.00mm - 195.00mm7.08" - 7.67"

TSU9912A50190.00mm - 205.00mm7.48" - 8.07"

TSU9912A55207.00mm - 222.00mm8.15" - 8.74"

TSU9912AF1220.00mm - 235.00mm8.66" - 9.25"

TSU9912A70240.00mm - 255.00mm9.45" - 10.04"

TSU4612AF3250.00mm - 265.00mm9.84" - 10.43"

TSU9912A80261.00mm - 276.00mm10.28" - 10.87"

TSU5012AF8280.00mm - 295.00mm11.02" - 11.61"

TSU9912A95290.00mm - 305.00mm11.42" - 12.00"

TSU9912110320.00mm - 335.00mm12.59" - 13.19"

TSU9912115330.00mm - 345.00mm12.99" - 13.58"

TSU9912130362.00mm - 377.00mm14.25" - 14.84"

TSU9912135370.00mm - 385.00mm14.57" - 15.16"

TSU9912140381.00mm - 396.00mm15.00" - 15.60"

TSU9912145389.00mm - 404.00mm15.31" - 15.91"

Please select your length below. 

BMW’s are known to have failure prone front thrust arm bushings.  The flexible rubber bushings, even those found in M performance models, allow significant movement of the front wheels to maximize daily driving comfort, but also allow considerable alignment change.  This results in a disconnected and numb road feel, standing between you and a confidence inspiring driving experience.  Eventually the fluid filled rubber bushings fatigue and crack due to continual deflection and ozone degradation, and eventually the damping fluid leaks out resulting in complete failure. 

For the enthusiast looking for superior performance and longevity with a crisp, confidence-inspiring driving experience, our sealed ball joint monoballs are the best solution available!  Our experience with spherical front control arm ball joints go back to those we designed and used in our IMSA E90 328i and E92 M3 racecars (GS class Champions in 2011).  We wanted to offer E31, E32, E34, E38, E39, E53, E60, E63, E64, and E83 owners similar levels of handling precision and control for the track and street. 

The bearing housing is precision CNC machined from 6061-T6 anodized aluminum and features a knurled OD to ensure a perfect press fit, and utilize a sealed OEM BMW ball joint for exceptional quality and durability, making them completely at home on both the street and track with no compromise.  We have done extensive street, autocross, and track testing to ensure the ball joint used in this bushing design excels in each setting.  The advantage of a sealed ball joint is that it eliminates all unwanted deflection while still allowing complete bind-free movement throughout suspension travel, resulting in exceptional control of wheel alignment.  What you get is superior steering precision, turn-in response, direct braking feedback, and better handling.

In short, if you're seeking the ultimate in precise, predictable handling and control, with crisp braking response and a long service life that’s equally at home on the street or track - look no further. We have you covered.

Features:

Bearing housing

• Precision CNC machined from 6061-T6 blue anodized aluminum
• Knurled OD to provide the perfect fit for the wide range of thrust arm bore diameters among brands.
• CNC machined 304ss ball joint sleeve inserts, providing a precision fit between the ball joint and the subframe. 

Bearing

• OEM BMW sealed and greased ball joint for exceptional durability and service life.

Performance

• Nearly instantaneous, crisp steering and braking response.
• Maintenance free, long lasting performance. 
• Improved road feel without undesirable NVH.

Since BMW recommends the control arms be replaced for every other bushing change, we prefer to sell these as a pre-assembled set, and are available separately here if you would prefer that option.

This item is an upgrade to the following rear wheel drive BMWs: 
2014+ F22 BMW 228i 230i M235i M240i - Coupe
2014+ F23 BMW 228i 230i M235i M240i - Convertible
2012+ F30 BMW 320i 328i 328d 335i 340i - Sedan 
2014+ F32 BMW 428i 435i 440i - Coupe 
2014+ F33 BMW 428i 435i 440i - Convertible 
2014+ F36 BMW 428i 435i 440i - Gran Coupe

Modern BMW's are beginning to leave the performance derived handling and power delivery in the past as the demand for more comfort and features rises. The stiff suspension components designed around having the best driving experience from a luxury car has been left for the M models and replaced with soft rubber bushings and mounts. Unfortunately, this is a good move by BMW to support the masses.

The obvious approach was to offer products so the modern BMW can be upgraded into the car the enthusiast desires, superb handling, control, and a direct delivery of power to the rear wheels. When you upgrade to our Delrin subframe mounts you reconnect that power with almost zero negative feedback.

The added appeal to someone looking to take one of these machines on the race track is Delrin can be used when solid mounts are needed and aluminum is not an option with strict regulations found in Grand-Am, BMW CCA, and other racing series.

Product features:

• Precision machined Delrin(TM) 150 bushings.
• Precision machined 6061-T6 aluminum inserts. 
• Class legal for any racing class that does not allow a solid subframe bushing. 

Performance Benefits:

• Eliminates subframe movement for more direct throttle and suspension  response. 
• Minimizes wheel hop due to subframe deflection and movement. 

***Installation Instructions***

These GAC differential bushings/mounts fit the following BMWs: 
2014+ F22 BMW 228i 228iX M235i M235iX 
2012+ F30 BMW 320i 320iX 328i 328iX 335i 335iX - Sedan 
2014+ F34 BMW 328i 328iX 335iX - Gran Turismo 
2014+ F32 BMW 428i 428iX 435i 435iX - Coupe 
2014+ F33 BMW 428i 428iX 435i 435iX - Convertible
2014+ F36 BMW 428iX -Gran Coupe