BMW Intake Parts for BMW 2 Series F22 (2014+)

A performance intercooler is a must when looking to get the most performance possible from your vehicle. Stock intercoolers are great for daily drivers but don't quite meet the demands for airflow and cooling when used on the track. CSF is here to remedy this situation with their all new High Performance Intercooler.

CSF has built up a reputation for themselves as one of the top contenders in the aftermarket community for performance cooling. With the success of their side mounted intercoolers for the S55 engine in the F8X M3 and M4, they have shifted their focus to the N55 and N20 platform. Their designs are a tried and true method using a bar and plate, stepped core intercooler. This, combined with the naturally high build quality of CSF products, will enable this motors to freely pull a much greater amount of air into the intake all while keeping things cooler than stock. This allows the engine to build power all throughout the RPM-band without the restriction that would normally start to be seen above 4500 RPM.

Features:

• Stepped core design for maximum surface area contact and internal intake air-flow volume. Largest “drop-in fit” intercooler available in the industry.
• Designed with 3D scanning / rapid prototype technology to ensure precise fitment and maximum surface area utilization. Lab tested on CSF’s in-house wind tunnel.
• Rounded front face bar/plate design for optimized airflow through the core. *A CSF World Exclusive*
• Drop-in fit” design for an easy & quick plug-and-play installation. Complete with OEM style “Quick-Connect” inlet/outlet connections.
• Fully reversible back to OEM spec with no modifications needed.
• ~40 *F drop in temperatures when compared to the OEM intercooler after multiple repeated runs.
• Power increase of 15-20 hp on stock cars, 25+ hp on modified vehicles.
• Available in silver (#8115) and matte black (#8115B)
• Lifetime warranty.

This Blow Off, or Dump valve, is for the BMW N20 2.0 Turbo engines that have the electronically controlled bypass valve. It is recommended for any vehicle where the boost pressure has been increased by an ECU software upgrade and for unmodified vehicles operating in warmer climates, as a solution to the many failures that have occurred, where the original rubber diaphragm splits, which causes a loss of boost pressure. Unfortunately the failure doesn’t always result in a check engine light as the valve can still be blown open by the boost pressure, so you may not be aware that you are losing power due to this.

Our alternative is a fully engineered solution offering significantly improved reliability. Our valve is piston based with no diaphragm to fail, and of all aluminium construction. It replaces the original unit with a pressure/vacuum operated piston valve that still also retains the desirable OEM ECU control over valve actuation.

7" Tall Air Filter:
This intake system utilizes an oil-free, 7" tall conical 360-degree radial flow performance air filter with 5-layers of progressive finer mesh cotton media providing maximum airflow and performance.

High-Quality Tube:
This system uses a high quality, dyno-tuned intake tube to achieve maximum power gains while maintaining a perfect fit.

Lightweight Vacuum Form Plastic Cover w/ Auxiliary Air Inlet:
Creates a stealthy under-hood look while reducing air intake noise without sacrificing power. A urethane plug is also included if you wish to block off the auxiliary air inlet.

Hassle-Free Installation:
All clamps, coupling, and hardware are included for hassle-free installation. This is a direct bolt-on kit that requires no cutting or drilling on factory parts.

Note 1:
Does NOT fit Convertible models.

Note 2:
This product is not currently CARB exempt and is not available for sale in California or for use on any vehicle registered with the California Department of Motor Vehicle.

This part fits the following BMWs:
F3X B58 
 

Forge's larger intercooler installs with no cutting or even removal of bumpers.

After a quick and simple install, you can expect temperature drops of 25 degrees Celsius. Lower temperatures leave room for more power and less heat soak thanks to a larger cooler charge. This intercooler features a bar and plate design core, featuring overall larger dimensions that improves cooling ability in comparison to the stock intercooler.

This product fits the following BMWs:
2014+ F22 M235i M235iX
2012+ F30 335i 335iX