BMW Intake Parts for BMW 2 Series F22 (2014+)

We are proud to present you with our long-awaited Turner Motorsport Carbon Fiber N55 Intakes. Like all of our Turner Motorsport products, our N55 intake was CAD Designed in-house to give you the best performing, most beautiful intake we could possibly imagine for your N55 powered BMW. The best part? Our design seamlessly integrates with OEM ducting and stock mounting locations to give you a simple install and an OEM+ fit and finish. We believe this is the way the N55 engine bays should have come from the factory. It’s time to ditch all that plastic.

Our higher flow filter and intake design gave our F30 335i an additional 7 WHP and 14 ft-lbs of torque over stock when we tested on our dyno. Our less restrictive intake design reduced post filter pressure by 0.2 psi over stock, allowing for gains across the entire RPM range - this reduced pressure drop also results in less stress on your N55’s turbo. Our enclosed intake also lowers your intake temperatures by 13 degrees over running an open intake.

We offer our N55 carbon intake in either gloss or matte finish, so you can choose what best suits your engine bay. Select either gloss or matte finish below, and then please select whether or not you are purchasing an intake for a manual transmission vehicle. If your vehicle has a manual transmission, it will require BMW Part # 13907515387.

If you are looking for our Turner Motorsport Open Carbon Intake, see T#568168

Download PDF Installation Instructions

Key Features & Benefits:

2x2 twill weave carbon fiber, clear coated for UV protection

Wrinkle Black Powder Coated heat shield

Ovaled Intake tube for OEM quality fitment

High flow cleanable Turner Motorsport air filter

+7 WHP / +14 lb-ft of torque!

Lowers intake temperatures by 13 degrees over running an open intake.

Special care instructions:

If clear coat gets scratched, reseal affected area with clear coat touch up

To retain UV resistance and protect finish, wax with high quality carnuba wax

Our N55 Carbon Intake fits the following BMWs:
2014 - 2016 F22 M235i, M235i xDrive
2012 - 2015 F30 335i, 335i xDrive
2012 - 2015 F32 435i, 435i xDrive

Want more in-depth details? We’ve got you covered below:

Carbon Fiber Intake Lid:

2x2 twill weave carbon fiber, protected by a clear coat for UV protection

Reduces intake temperatures by 13 degrees compared to running an open intake

Carbon Fiber Intake Tube:

2x2 twill weave carbon fiber, protected by a clear coat for UV protection

Ovaled intake tube design allowing

MAF scaling matches factory intake

MAF sensor flange machined from 6061-T6, black anodized and bonded to the intake tube directly in the center of the tube for accurate temp/airflow reading

Vacuum line port machined from 6061-T6, black andozed and bonded to intake tube

Integrated carbon flange allows secure mounting of intake tube to our heat shield

Heat shield:

One piece design manufactured from 12 gauge 5052 aluminum

Wrinkle black powder coated

Supplied gold heat shield tape

High Flow Air Filter:

Conical high flow cleanable air filer

8 ply oiled cotton gauze

Bellmouth filter flange inlet reduces turbulence and maximizes flow

Engines make more power when you're able to move as much air and fuel as possible through them. However, air density is just as important as air volume. Cooler air is denser air, so in addition to keeping your engine cool, it's important to make sure that your intake charge is as cool as possible. Turner Motorsport's upgraded intercooler works to reduce air temperatures with a bare minimum of pressure drop. Less pressure drop means less restriction, and a turbocharger that doesn't have to work as hard. This results not only in a longer service life for your turbocharger, but a substantial increase in performance as well.

The stepped design increases volume and surface are in a limited space by adding an additional smaller core at the top of the intercooler. Both cross sectional area and frontal surface area are increased by a whopping 56%, with a design that still weighs under 20 pounds. On the stock intercooler, the temperature differential between the inlet and outlet sides of the intercooler represented a 95 degree drop. With the Turner Motorsport intercooler, that drop was increased to a chilling 140 degrees. The dyno results don't lie: as a bolt-in upgrade, expect gains of 18 wheel horsepower and 10 lb/ft of torque. With a tune and supporting modifications, further gains are possible, up to 36 horsepower and 28 lb/ft of torque.

This cast aluminum intercooler features an attractive, easy to clean matte black finish, with etched Turner logos on the front and bottom. If you're looking for the ultimate cooling system upgrade for your turbo BMW, look no further.

• Cast aluminum construction
• Bar and plate design
• 56% increase in frontal surface area & cross sectional area
• Decrease in temperature of 45 degrees from inlet side to outlet side (95 degree drop stock on outlet side vs. 140 degree drop on Turner outlet side)
• Significantly less restriction (pressure drop of consistently 0.75 psi vs. 1.5-2.5 psi stock)
• +18HP/10TQ (+36HP/28TQ with tune and supporting mods)
• Weighs under 20 lbs.
• Overall size: 520mm wide, 210mm tall
• Mounting hardware inlcuded

Upgrade to the following OE Intercoolers: 17517600531, 17517600530, 17517618809

Fits the Following BMWs:

F22 F23 228i 228i M235i M235ix

F30 F31 F32 F33 F34 F36 328i 328ix 335i 335ix 428i 428ix 435i 435ix

This is a short ram intake and filter kit that will go in place of the restrictive and unattractive factory airbox. Feel a dramatic boost to throttle response and build boost faster by eliminating restrictions and widening the intake track. The Injen SP Series Intake Systems Feature the Patent Pending MR Technology Process for Optimal Gains and a Safe A/F Ratio. The Injen SP Series Intake System does not limit itself to just a Cold Air System or Short Ram System. The MR Technology process has its effects on both types. The Injen SP Series Intake is The World's First Tuned Intake System.

In 1999 Injen designed the first urethane filter with a built-in velocity stack for added performance. The Injen Technology Research and Development Team calculates each filters mesh and pleat count for each specific application during the development stages. Today the state-of-the-art Ea nano-fiber Injen/AMSOIL performance dry filter provides reliable performance and requires NO OIL. Both Injen Air Filters allow cleaning and durability for 1000's of miles to come.

Features:
Powdercoated heat shield
Polished short ram tubing
+13hp/11ftlbs.

Kit Includes:
Short ram intake piping
Heat shield 
SuperNano Dry Web Dry Filters
Mounting hardware
Instuctions

This part fits the following BMWs:
2016 BMW M2 (F87) 
2014-2016 BMW M235I (F22) 
2012-2015 BMW 335I/IX (F30/31/34) 
2014-2016 BMW 435I/IX (F32/33/36) 

The stock air box in many BMWs is the first point of restriction to air flow and power. The Evolution Intake from Injen is a great option for increased airflow and power, up to +15hp and +16ft/lbs of torque, while still retaining a clean look without being overly flashy like many other intakes on the market. Featuring CAD and 3D designed Roto-Molded Polyethylene (Heavy Duty Plastic) construction and a larger SuperNano-Web Dry Filter, this drop-in intake system offers a significantly higher air flow rate and easy installation with no modifications needed.

Product Features:

• Complete intake design, including the intake chargepipe,
• Designed To Work w/Stock Calibration
• Aggressive Intake Tone Under Acceleration
• Roto-Molded Polyethylene Tube And Housing
• Reinforced Automotive Grade Silicone Couplers
• Stainless Steel Band Clamp w/Inner Protective Liner
• Larger Inlet Air Scoop And Induction Tube
• Midnight Edition Injen Badge
• Made in the USA

Notice of Emissions Non-Compliance. This product is not legal for sale or use in California on any pollution-controlled motor vehicle.