BMW Suspension Bushings & Mounts for BMW 2 Series F22 (2014+)

Strut mounts can begin to wear and fail over time, causing a knock in the suspension to occur. Replace yours with a Genuine BMW replacement to ensure a tight, noise-free ride.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Genuine BMW Guide Support -
This item fits the following BMW Chassis:
F22,F30,F31,F32,F33,F36

For someone looking for superior performance and longevity these sealed monoball bushings are the best upper thrust bearing you can buy for an F22 2-series or F3X 3/4-series. The advantage of a monoball bearing is that it will not deflect under load. All of the rubber bushings move in all sorts of directions and that changes your alignment, especially when used with big brake kits or when driven hard. The condition worsens as the bushing wears out. The Dinan monoball sits in a CNC machined aluminum housing which has zero deflection. The monoball allows complete freedom of movement but only at the desired angles. What you get is superior steering precision, better handling from more consistent alignment, and almost infinite bushing life. And thanks to the inner liner and sealed rubber boots there's none of the extra noise or reduced service life of fully solid race bushings. 

We strongly advise using these with new control arms. BMW recommends that the bushings be replaced only once per set of control arms. So if your thrust arm bushings have been replaced already then we do not recommend re-using the arms. The other reason is that the aluminum arms stretch over time which will make the bushings loose inside the arm. Other manufacturers recommend filling the stretched arms with paste but replacing the control arm is the better solution.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere.

This item fits the following BMWs:
2014+ F22 F23 BMW 228i M235i
2012+ F30 BMW 320i 328i 335i - Sedan
2012+ F32 BMW 428i 435i - Coupe
2013+ F33 BMW 428i 435i - Convertible
2012+ F34 BMW 328i 335i - Gran Turismo
2012+ F36 BMW 428i 435i - GranCoupe

Modern BMW's are beginning to leave the performance derived handling and power delivery in the past as the demand for more comfort and features rises. The stiff suspension components designed around having the best driving experience from a luxury car has been left for the M models and replaced with soft rubber bushings and mounts. Unfortunately, this is a good move by BMW to support the masses.

The obvious approach was to offer products so the modern BMW can be upgraded into the car the enthusiast desires, superb handling, control, and a direct delivery of power to the rear wheels. When you upgrade to our Delrin subframe mounts you reconnect that power with almost zero negative feedback.

The added appeal to someone looking to take one of these machines on the race track is Delrin can be used when solid mounts are needed and aluminum is not an option with strict regulations found in??Grand-Am, BMW CCA, and other racing series.

Product features:

• Precision machined Delrin(TM) 150 bushings.
• Precision machined 6061-T6 aluminum inserts.?
• Class legal for any racing class that does not allow a solid subframe bushing.?

Performance Benefits:

• Eliminates subframe movement for more direct throttle and suspension? response.?
• Minimizes wheel hop due to subframe deflection and movement.?

?

***Installation Instructions***

These GAC differential bushings/mounts fit the following BMWs:?
2014+?F22 BMW?228i 228iX M235i M235iX?
2012+?F30 BMW?320i 320iX 328i 328iX 335i 335iX - Sedan?
2014+?F34 BMW?328i 328iX 335iX - Gran Turismo?
2014+?F32 BMW?428i 428iX 435i 435iX - Coupe?
2014+?F33 BMW?428i 428iX 435i 435iX - Convertible

2014+?F36?BMW?428iX -Gran Coupe?

Tasked with keeping the vehicles rear end firmly mounted while absorbing noise, vibration, and harshness (NVH) factory rubber subframe bushings were engineered to provide a balance of control while keeping the ride quality soft and supple. As a factory bushings age, they become brittle and begin to harden. When this happens the bushing will actually shrink and allow excess play, or movement in the subframe. This is typically felt by a sudden jerk or "thunking" noise under acceleration and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushings with full polyurethane this play is eliminated since the subframe is being held in place by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering and acceleration inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver. 

Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.